Steve working my way through the videos gradually, Great information mate! love it
@bianchetfam7960
4 жыл бұрын
Really enjoying your vids all the over here in NZ. Quick, easy to understand and technical. Thanks
@paulstephans3364
4 жыл бұрын
Great video steve👍
@CarlEves
4 жыл бұрын
Really interesting video as usual. I never really knew how to use the visualiser properly. My imola has 15x46 with an Italian Li150 box and CHT3 exhaust. I’ve tried 16x46 and 17x46 but it dies in 4th gear especially the 17x46 set up. Shame really as it flew in the first 3 gears 😄. As always after watching this I’m thinking of changing exhaust to perhaps a CHT5 to bring the top speed up. But then again who blasts around in top revs all the time. During lockdown these videos give me lots of thinking time which is dangerous for my wallet 😄😄
@TheSteelweasel
4 жыл бұрын
the imola has high port timings and needs to rev to make power . CST3 is wrong exhaust i would fit jl4 race it will be better on 15.46
@TheSteelweasel
4 жыл бұрын
the other option is to machine 1mm off base of cylinder lowering port timings and keep same exhaust it should then pull higher gearing ....... you will have to put a thicker head gasket .
@CarlEves
4 жыл бұрын
TheSteelweasel hi mate. Is there another pipe you would recommend. My mates have all had problems with the JL4 splitting. I’d rather not machine the cylinder I haven’t got the skills to do all that tuning stuff. 😄
@TheSteelweasel
4 жыл бұрын
@@CarlEves hi carl i got the jl 4 for 120 pounds direct from them ,,,,, the CTS5 is 365 pounds , ive had no problems with the jl i can only think your friends didnt fit it correctly and it was loose allowing it to crack ? up to you my friend
@CarlEves
4 жыл бұрын
TheSteelweasel to be honest mate if it’s only £120 it’s worth the punt. I have got a robbospeed pipe here which I think was comparable to a JL4 but I can’t remember now. I took it off as it fitted quite close to the panel and it rubbed the panel.
@midge225
4 жыл бұрын
Another great viseo ste , quick question tho m8 , when you buy a new chain , depending on your gears are going to set up , what length chain would you need for each individual gear set up m8
@TheSteelweasel
4 жыл бұрын
depends what chain tensioner your using with the casa x44 you can get away with more adjustment this is a 82 link with 19 / 46 sprokets . its an idea for a vid mate .....
@midge225
4 жыл бұрын
@@TheSteelweasel got ya ste , i just wondered lol
@paulstephans3364
4 жыл бұрын
Hi Steve just wondered what you think of my set up 16 front 47 large sprocket TV series 3 gear box casa chain tensioner 82 iwis chain casa 185 kit ported pwk28 mm gori 50mm exhaust casatronic 12v Cheers buddy
@TheSteelweasel
4 жыл бұрын
What is your weight and hight?
@paulstephans3364
4 жыл бұрын
@@TheSteelweasel 14.2 stone 5.8
@TheSteelweasel
4 жыл бұрын
All looks very good on paper except the gear box ? TV is to high for this motor
@paulstephans3364
4 жыл бұрын
@@TheSteelweasel what do you recommend or will it be ok just whant cruising for about 65 70mph Appreciate your feed back buddy👍
@TheSteelweasel
4 жыл бұрын
14 stone well most people are around that weight ? If you go two up you won't get out of third . LI 150 ITALIAN 17 . 47 OR PACEMAKER 17 47 or 5 speed close ratio 18 47
@TheSoldatone
2 жыл бұрын
Thank you for the video . tell me what the program is. in which you can select stars and drives for the Lama
@TheSteelweasel
2 жыл бұрын
Lambretta gearbox visualizer . Free down load
@TheSoldatone
2 жыл бұрын
@@TheSteelweasel 🙏
@TheSoldatone
2 жыл бұрын
@@TheSteelweasel I have sul 150 Gp. what do you advise ? change bearings and seals? or not to climb into the motor until it breaks down?
@TheSteelweasel
2 жыл бұрын
@@TheSoldatone if it runs well with no problems then dont touch it . If it's got lots of mileage and runs badly or noisy strip and rebuild , beware old cranks they can fail even if they dont have play , I would replace this with a good quality one on any rebuild .
@TheSoldatone
2 жыл бұрын
@@TheSteelweasel compression is not measured. well it works fine. he came from india after restoration and was on the move. then he fell on his side and got to me. the motor runs smoothly well, the kick starter grabs at the very end
@lukemehaffey91
4 жыл бұрын
What visualiser are you using. Could do with it for a restoration I'm planning.
@TheSteelweasel
4 жыл бұрын
Lambretta gearbox visualizer
@georgeyboyhowe1685
4 жыл бұрын
morning hows it going keep safe pete
@TheSteelweasel
4 жыл бұрын
yes thanks ... hope you and your family are safe all the best ........
Пікірлер: 37