Did the job. Observed the five turns. Once fitted and used the screwed in side was forced off and became detached from the module. Brake failure! Watched this video afterwards to see if I had done anything wrong. I have not. Grrr. Must be another problem. Land Rover we love you. We love you to death Lol.
@maxautouk
Жыл бұрын
The most common cause of failure in your exact issue is incorrectly fitted or corroded or broken handbrake return springs, it's the spring that goes on the brake cable inside the drum and wraps around the arm of the brake shoe
@matthapaq9618
2 ай бұрын
Mate great video thanks . After I did what u did exactly all back on put silicone install it all back, try still handbrake light on flashing and no sound from motor as I test it before it’s working like clock , do I need do anything else?.. Cheers Matt
@maxautouk
Ай бұрын
Is the motor power cables clipped on correctly?
@rustytwinkles7762
Ай бұрын
I need to replace the board in mine. Do you think it could be swapped over with the module in place on the truck?. Thanks
@maxautouk
Ай бұрын
It may very well need recoding to the vehicle with a diagnostic tool if the circuit board is swapped
@rustytwinkles7762
Ай бұрын
@@maxautouk okay, thanks 👍🏻
@sveinistube
7 ай бұрын
Great video! Any idea what the part (hand brake mechanism) with the blue plug is called, or what part number it has? Managed to break the the thin, orange wire on mine...
@maxautouk
7 ай бұрын
I’m not sure what you mean, do you mean the plug that stays in the car broke?
@sveinistube
7 ай бұрын
@@maxautoukI mean the white plastic piece in the bottom left, that latches with the screw coming in from the right. It has an orange “ribbon wire” that goes up to the blue plug. You reconnect it at 10:47 in the video. Anyway, managed to source a used one to replace the one I broke, hope it works 😅 Thanks again for a great video👍
@maxautouk
7 ай бұрын
@@sveinistube let me know how you get on 😁
@robblount1299
Жыл бұрын
Great job, very informative 👍🏼, but you would be more comfortable working at a bench🤔
@maxautouk
Жыл бұрын
Thanks for the comment I do have a bench, and workshop and lift but I like to show the DIY approach on my videos 👌
@joelharris8198
9 ай бұрын
Just watched your videos of EPB Removal and Rebuild, How long did the job take?
@maxautouk
9 ай бұрын
Probably four hours spread out over a few days waiting for parts and such
@andrewmurray4113
Жыл бұрын
What did you do about the broke circlip that holds the cables in to the backing plates
@maxautouk
Жыл бұрын
I have a box of c clips so I just popped in some new ones
@andrewmurray4113
Жыл бұрын
@@maxautouk one of mine broke one came out complete so I will have to get a couple before I can finish mine
@maxautouk
Жыл бұрын
@@andrewmurray4113 if the spring on the inside of the backing plate that hooks over the lever arm of the cable is corroded or damaged replace that too or it will let the epb cable slip out and you'll need a scan tool to set it back to the latching position
@andrewmurray4113
Жыл бұрын
@@maxautouk my new cables have come with new springs that attach to the lever arms of the shoes, any idea on what size these clips are that hold the cables into the backing plates? Cheers
@maxautouk
Жыл бұрын
@@andrewmurray4113 I'd guess 17mm but I always buy them by the tray so I don't really measure I just keep grabbing them until I get the right size
@expedition320
4 ай бұрын
Can the EPB be removed without removing all the cables to the cab and the shoes.
@maxautouk
4 ай бұрын
I must admit I haven’t tried this myself but I think you need to remove the cables
@joshualamb4060
Жыл бұрын
Hi buddy this is proberly a long shot as this was a year ago but I've done my ebp a few weeks ago managed to get another look at it today and even if I manually latch it on as soon as the handbrake is applied from inside the car it just detaches with out hardly any force and its got me completely baffled as I've reassembled all the shoes and everything again and I cant see anything wrong but I'm obviously missing something somewhere
@maxautouk
Жыл бұрын
Is the spring inside the backing plate broken? It needs to hook around the lip where the handbrake cable comes through and it needs to latch into a groove on the retaining tab on the lever otherwise the cable will repeatedly slip out
@joshualamb4060
Жыл бұрын
@@maxautouk yes both sides are as I checked that today after reading the comment someone else left onthis video but there defiantly in and onto the retaining tab of the groove inside the arm on the shoe
@maxautouk
Жыл бұрын
Might be worth checking all of the basics again like the setting of the shoes, making sure the handbrake cables are all moving inside their sleeves etc
Пікірлер: 29