Bro, you need a bandsaw asap!! It would make your life so much more easy/efficient in the shop
@antonmursid3505
2 жыл бұрын
Antonmursid🙏🙏🙏🙏🙏🇲🇨
@amanofmanyparts9120
2 жыл бұрын
Failing that due to _poverty,_ a decent angle grinder and a few 1mm cutting discs would do the job much faster. For greater accuracy an angle grinder based 'chop saw' attachment is advised.
@TheDistur
2 жыл бұрын
Hacksaws build character.
@TalRohan
2 жыл бұрын
its his daily work out and good for his biceps leave him alone :0)
@ev_dyno743
Жыл бұрын
buy him one then
@gary851
3 жыл бұрын
Please make a patron account so i can donate for a portable handsaw - my bone marrow hurts when i see someone cut stock by hand!
@Barronohbeefdipp
3 жыл бұрын
I was just typing this haha. Make a bandsaw you have a lathe and mill. I love the videos but I cant take the hack saw cutting it sets me off haha.
@jakubkopec9313
3 жыл бұрын
For heating small parts you can put them in a small ceramic flower pot. They will heat much faster, as placing them on metal sucks heat out of them.
@trashes_to_treasures
2 жыл бұрын
Great tip!
@KaneDesign
3 жыл бұрын
It’s nice to see that, at least in the comments I’ve read, that everyone seems quite positive. Too often on hobbyist machinist channels the comments are overly negative and provide next to zero constructive criticism. Love your videos as of late man, keep it up👍
@artisanmakes
3 жыл бұрын
Cheers, always open to feedback, I find it very useful.
@artisanmakes
3 жыл бұрын
G'day, I hope that you enjoyed this video. It has been in the pipeline for a very long time, and I jumped at the opportunity to make it as soon as I got the new mill. A few things that I wasn't able to cover in the video: 1- Addressing the use of mild steel: Mild steel was not my first choice of material, and in have concerns about galling (though i won't have to worry about this for a while) but given the small amount of material I required, I just couldn't find a local supplier that stocked what I needed. With my state now in lockdown, this supply was issue was compounded. However the mild steel seems to be performing well. Good lubrication should help reduce galling. And the added benefit of using mild is an increase in tensile strength, compared to the cast. 2. The fly cutter, whilst doing a great job is flawed. I mistakenly machined it with the bolts on the wrong side, so the bolts are pushed against whilst it is machining. Long Term, i will have to fix this.
@Joe_Bandit
3 жыл бұрын
I have been looking around for cast iron stock too and the best I've found is weight plates from Kmart. Looks like you'd be able to get a decent 20mm piece from the 10kg. Not sure the quality of the castings though.
@HM-Projects
3 жыл бұрын
@@Joe_Bandit Primehyd in WA stock cast iron flat bars. Not cheap though.
@artisanmakes
3 жыл бұрын
@@Joe_Bandit Funnily enough I have actually torn apart a scrap 1kg weight from Kmart to machine the cast iron it is made of. Not the greatest castings but they worked fine as small flywheels for the project I did. The only thing that I might have to look into about these is what type of cast iron they are made from. typically you would want to use a grey cast iron for machines.
@Joe_Bandit
3 жыл бұрын
@@artisanmakes good to know, thanks!
@timplett1
3 жыл бұрын
Regarding the fly cutter as it is, you should be able to flip your cutting tool and run the spindle in reverse, at least to verify whether taking the time to fix/remake it will make a difference.
@barryfitch6920
3 жыл бұрын
Great addition. Please put more gibb strip screws in place for smoother action eg. 5 or 6 gibb strip screws, with perhaps just one screw as a lock G screw only. This will definately improve your lathe. Keep the chips flowing!!!
@BedsitBob
2 жыл бұрын
When cutting T-Slots, it's a good idea to cut the initial centre slot 5 thou deeper, than the depth the T-Slot cutter will be set to. Doing it that way, reduces the tool pressure.
@DuRöhre4711
2 жыл бұрын
aaand the T-Slot Nuts will ride much better even if you ruined the bottom once with a too long of a bolt :)
@ourtube4266
10 ай бұрын
That’s great advice thank you.
@bmacpher
2 жыл бұрын
I'm with you all the way on the cross-slide T slots - I wouldn't have considered making my own cross slide for my lathe, so thanks for another project to add to my list 😁
@artisanmakes
2 жыл бұрын
Best of luck. Cheers
@andrewcullen3235
2 жыл бұрын
Have really enjoyed your channel since subscribing. Keep rocking the hacksaw the frustration about it in all the comments cracks me up. Cheers
@tonyandjackieholmes9546
3 жыл бұрын
Thanks for another great upload - if nothin else I'm in awe of any bloke who can hack saw straight :)
@artmckay6704
3 жыл бұрын
Wow! Nice work! I can definitely see that you'd have a much more rigid setup than before. You'd think it'd be a no brainer for manufacturers to supply machines with your mods already in them. Thanks for sharing this! :)
@henrydando
Жыл бұрын
There are compaines who do, and they don't get customers as the customers pick the cheapest machine 9 times out of 10
@artmckay6704
Жыл бұрын
@@henrydando I've learned the hard way that it's always the better way to just bite the bullet and pony up for the quality option. Today, I even buy top of the line paper towels because they so outperform the cheap crap. It's the same with machine tools - one should buy the most expensive tool that they can afford because it'll outperform 10 of the garbage machines. It pays to buy the best that one possibly can. Imho.......
@kyleteodecki7478
3 жыл бұрын
ive considered doing this myself, given access to a "real" mill. was curious if you considered goin with a smaller mating dovetail and thinner gibstrip to reduce the rotational deflection.
@MattOGormanSmith
3 жыл бұрын
If you made angled brass slugs to go under the gib adjusters, they'd spread the pressure on the gibs and you could use shorter grubscrews
@artisanmakes
3 жыл бұрын
I didn't think of that, ill have to look into it, thankyou.
@Festivejelly
Күн бұрын
I need to do this. I dont using a compound anymore. So the cross slide can be higher and have t nut profiles. Ideal for my CNC conversion.
@qwertyu19951
Жыл бұрын
I am amazed by the things you manage to do with that small milling machine!
@philmenzies2477
2 жыл бұрын
Very nice work. That broken tap could probably have been removed by EDM. I have seen some successful home made units.
@davidrivaz
3 жыл бұрын
I was looking for something like this on Littlemachineshop, but they only have it for the compund slide at the moment. Why not make it even larger? Maybe able to fit gang tooling.
@artisanmakes
3 жыл бұрын
If I would make it longer I'd need to modify the cross slide leadscrew and the carriage to have extra travel to make use of the longer slide
@philoso377
2 жыл бұрын
Nice production and excellent idea. I have been thinking of this upgrade but never get started. This video triggers me of my next upgrade to go.
@melgross
3 жыл бұрын
Be careful with the holder for the post. It’s thin on top. I made one similar for my smaller lathe. At some point the top, with the screws, just broke off. The next one was made with a thicker top.
@dmw_cutlery
3 ай бұрын
I love your work by the way. what dovetail cutter did you use and what kind of cutter did you use to make your T slots. I would like to make the same modifications on My lathe. thanks
@steveforbes8287
Жыл бұрын
Very nice and quite well done. I am of the opinion that if you were to use a lubricant when tapping you would not have broken your tap. I saw no evidence that you used a lubricant when tapping and that is just asking for breakage.
@NOTSOSLIMJIM
6 ай бұрын
Lol, I'm rebuilding my tailstock right now
@Simon67316
6 ай бұрын
Do you sell these parts? I’d buy the brass gib you made as I don’t have a milling machine as my carriage which looks identical to yours is not ridged to say the least.
@nifty1940
2 жыл бұрын
An amateur wants to know if a plate could have been solidly mounted on the existing slide to achieve the same features and rigidity. Please excuse my ignorance.
@alliwantedisapepsi1492
3 жыл бұрын
This looks like my garage, only cleaner. Good job. Cheers.
@lennarthoek8392
3 жыл бұрын
Great video! Being a machinist myself I do have a few questions/critiques: are you planning on getting a better vice for your mill? Drilling vices often lack rigidity and accuracy and I can't imagine it being fun to use. I also noticed you use climb milling as well as conventional milling, I think considering the rigidity of the machine it would be better to make most cuts with conventional milling, or at least the finishing cuts. This should improve the stability as well as the surface finish a lot! Climb milling is often better for the tools, but just isn't viable if there isn't enough stability. Last but not least: when making a piece of material square and parallel in the mill, the best method is to cut a side, turn this side to the non moving jaw make another cut, turn again , cut again, turn again and then you should have 4 square sides. I hope I don't intrude to much and these tips are actually of some help, and for what it's worth you're doing way more and better stuff with a mini lathe then I ever did!
@jsublettusaf
3 жыл бұрын
That was an informative comment for me. Thanks! I've been doing it to the bottom of the vise thinking it was parallel to the table. I've also been doing climb & conventional on a mini mill only learning the difference yesterday. Good comment!
@ryebis
3 жыл бұрын
Do you mean taking rough cuts with conventional and then using climb for finishing passes ?
@lennarthoek8392
3 жыл бұрын
@@jsublettusaf that way you indees get two parallel sides, but if your vice is bad or there is a bit of dirt there's a big chance you get a parallelogram. But if you want the full explanation there are some really good video's om yt explaining it better!
@lennarthoek8392
3 жыл бұрын
@@ryebis normally yes, but if there is too much vibration or instability in either the set up, table or spindle. The mill could start "biting" into the material taking away more then it should and leaving a worse surface finish. You can actually see this a bit in the video, caused by I'm guessing a combination of all three factors, but two can maybe be fixed: trying another set up, like putting the material directly on the table, and clamping all the axis down, except the moving one ofcourse (but maybe he's already done that, in that case my apologies)
@artisanmakes
3 жыл бұрын
Thankyou Lennart, feedback is always very helpful. I am indeed planning on upgrading the vise. The vise was just a freebie that case with the mill from the supplier. Credit where it is due, it is probably one of the better drill press vises that I have used. Though I will be replacing it soon. The plan was to replace it ASAP, but my state is unfortunately experiencing a COVID lockdown, and my supplier is currently closed. My preference is to always check out the product before I buy it if I am able to. Currently looking at just grabbing an import one for the time being. As for the climb milling, to be quite frank, most times I did it just out of laziness, not wanting to move the table back so I could conventional cut it. Had to change up the when climb milling though. As for getting the part square, I have to conceded that is the proper way. There was a lot of shenanigans off camera that I had to do to check that everything was all square. Many thanks for the advice.
@lookingbehind6335
3 жыл бұрын
If only I had a mill.
@bhein67
2 жыл бұрын
You are getting far superior results to what I get on my mini-mill. What depth of cuts & feed speed are you using? I don't have a power feed so I struggle with consistency. I really enjoy your channel and the projects you do! Cheers from Canada
@artisanmakes
2 жыл бұрын
I think I was doing a 1.5/2mm depth of cut here at around 800rpm, the motor develops a lot of torque there. It is less than optimal but it works
@mauriziopagnotta8873
4 ай бұрын
Bel progetto! Una domanda lo spessore a coda di rondine che hai effettuato in ottone va bene anche alluminio o meglio ottone? Perché a casa ho tante barre in alluminio e gli spessori di serie fanno veramente schifo. Grazie
@fna-wrightengineering
3 жыл бұрын
Fantastic work! This is a great idea, and you made an awesome job of it. You should consider another M4 tapped hole between the front and middle gib adjusting screws, for a slide locking bolt. This also helps rigidity quite a bit. I made a very similar fly cutter (I also had to make it twice, due to putting the set screws on the wrong side the first time). If/when you make another, you don't have to make the tool slot at an angle. You can just make the bottom of the fly cutter flat, as well as the offset slot, because the tip of the carbide insert sticks out past the tool holder shank. That's how I did mine. Anyways, keep up the great work!
@artisanmakes
3 жыл бұрын
Didn't think of that, I'll have to do that, thankyou
@termlimit
2 жыл бұрын
Excellent video as always. If I could pick your brain, what dimensions did you use for the t-slot size and spacing? I'm doing this mod as well and I wondered if there is a standard I should opt for. Thanks again as always.
@artisanmakes
2 жыл бұрын
These are m8 size t slots. There are charts online that should give you the exact dimensions.
@termlimit
2 жыл бұрын
@@artisanmakes Brilliant thank you.
@Travehorst
Жыл бұрын
Guten Tag Artisan, deine Arbeit ( Gross Slide ) ist eine sehr gute Idee, ich habe auch eine Drehbank fast identisch ( Mini Lathe ) und möchte Das nach bauen , Bitte hättest Du eventuell die Material Maße LxBxH . Schöne Grüße aus Lübeck, Old Germany Horst ( Bitte Viel mehr so gute Arbeiten ).
@williamweesner1191
Жыл бұрын
You do some great work you’ve helped me make a decent machine out of nothing.
@artisanmakes
Жыл бұрын
Glad to hear it
@paulthomas3782
3 жыл бұрын
Great Idea thanks for sharing
@juhavuorinen3945
11 ай бұрын
Why you don't make taper adjustable gib when you make whole slide new?
@artisanmakes
11 ай бұрын
You could but for a mini lathe it really isnt worth the effort
@GBWM_CNC
3 жыл бұрын
I find it so satisfying to watch those fly cutters cutting 😍
@Brian18741
2 жыл бұрын
Great improvement 👍
@DittersGustav
Жыл бұрын
I know its been 2 years, but what dimensions are these t-slot cutters? 18mm x 6?
@artisanmakes
Жыл бұрын
From memory my one is a 18mm diameter by 3mm tall, the t slots are probably 5 or 6mm tall. If you search up M8 t slot standard size on google it will give you a bunch of dimensions, which I probably copied from
@ARIFINLATHE
3 жыл бұрын
You are very professional and I am very inspired by what you do on your manual lathe sir💯🤝🤝🤝🤝🤝
@DaleepEngineering
3 жыл бұрын
Great 👍
@kieranh2005
9 ай бұрын
I got a spray bottle with a nozzle that allows stream or spray and filled it with coolant solution. Spray as needed to cool/lubricate as my lathe doesn't have a coolant pump fitted. If you were using a lot, hook a catch bottle under table drain to recover fluid for re-use.
@dannymerry1786
Жыл бұрын
Get some rocol RTD cutting oil. It really improves finish when drilling reaming and tapping holes. Will make your drills last longer too
@dieselwelds8645
2 жыл бұрын
Can you please share the dimensions of your cross slide? I just got a piece of CR1018 1"x3.5"x6" bar stock and trying to plan out a new cross slide. Thanks!
@dieselwelds8645
2 жыл бұрын
wild guess - the bar stock / end product are roughly 20mm x 80mm x 160mm? Knowing the saddle is 100mm wide i paused the video, held a piece of paper against the screen and marked the ends of the saddle. Then folded the paper over, marked 50mm, then folded again to mark 25mm/75mm, then folded again... it provided a rough scale. thanks for all your video posts. i've gleaned a lot from your efforts and even though there are more experienced machinists on youtube, i really prefer your content the most simply for your editing style and voice/accent. and family friendly content as well!
@artisanmakes
2 жыл бұрын
Hey mate, from memory it was a 75x 25x 120 piece of mild steel. The overall size doesn't really matter, use what you can get, just make it big enough so you can squeeze in two M8 t slots and wide enough to mount your toolpost, and judging by the size you posted, your one will be about the same size as mine. As for the dovetails, cut them to match the existing dovetails on your cross side, same for the cross slide mounting holes. Take care.
@dev-debug
2 жыл бұрын
Cool project. I always wondered why they don't include T slots on cross slides, wouldn't cost much to do. You really need a small bandsaw, was one of the best investments I ever made for my shop :)
@artisanmakes
2 жыл бұрын
Absolutely a worthwhile addition. The t slots are a very useful addition to the lathe. Hope to have a workshop one day where I can have the space for a proper bandsaw. Cheers
@georgescarlett2320
Жыл бұрын
Amen! As per my suggestion as well!!!
@madmodder123
8 ай бұрын
@@artisanmakes gotta get a portable bandsaw and a hercules vertical/horizontal stand
@homemadetools
3 жыл бұрын
Excellent as usual. We shared this video in our homemade tools forum this week :)
@Ordog213
3 жыл бұрын
I have the same lathe and the smaller mill from Paulimot, the local dealer for the SIEG-Brand. I made the new retainer Strips for the Lathe and now thanks to you i know my nex project. In return i have maybe an idea you can use on your machine for indexing parts on the lathe. and i would like to send you a drawing for use on a 80mm 3 Jaw Chuck if you up for it. ;)
@watahyahknow
Жыл бұрын
might be able to heat the parts up faster and use less heat when blackening them if you put the parts on sumting that doesnt conduct and suck away heat been seeing some lathes with this type of t slot crosslide and was looking for one for my lathe (like to be able to adapt the lathe to increase the swing kzitem.info/news/bejne/poykqWiee32rnIY and need a bigger distance fo move the tool farther away from the center and raise it for that the T slots would allow for that while keeping the base sturdy , looks like there not that hard to make myself , just curious if you measured if its at the exact 45 degree angle seen a video where the stock slide was off by a lot and had to be reground to get it to work properly kzitem.info/news/bejne/yYWOmpmHoGmipI4
@multidomar
3 жыл бұрын
A before and after pass on material would be cool to see the improvement
@artisanmakes
3 жыл бұрын
Thankyou for the feedback
@cooperised
3 жыл бұрын
I liked "I accidentally broke the tap". As opposed to _deliberately_ breaking the tap? :-)
@CandidZulu
Жыл бұрын
Well done! I think it will be accurate enough as is w o scraping for almost anything you will do in a home work shop.
@paulwomack5866
3 жыл бұрын
I note that you mentioned how useful the 'T' slots would be for fitting a vertical slide. Of course, now you've got a mill, I guess your interest in vertical slides is gonna' be close to zero!
@artisanmakes
3 жыл бұрын
You are right, I probably won't be doing any milling with the slide, but other attachments such as a gear cutter I'm working on might require it.
@johnlocke9609
2 жыл бұрын
@@artisanmakes hello! Any news in your gear cutter attachment? Love to see your project!🙏
@pirminkogleck4056
2 жыл бұрын
hey Gday , can u tell me wich insert and holder u used here? and i want to know have u ever tried the sharp chrome inserts wich are usualy for alu ? i use them with a .4 nose radius and they work great even on steel, razor sharp
@andrew051968
2 жыл бұрын
Great job! I was just going to say - you really need a power hacksaw - then I saw all the other comments.
@nefariousyawn
3 жыл бұрын
Good job! Regarding the broken tap, have you ever tried a spring loaded tap follower mounted in the mill? I think it was Blondie Hacks that made one on her channel, looked like a great way to mitigate tap breakage. Also, what was that weird background sound at 10:09?
@gordonquigley2267
3 жыл бұрын
It was a Currawong, native bird to Australia about the same size as a Crow, very wide spread across Aus.
@artisanmakes
3 жыл бұрын
I made one a while ago but they tend to only work for Taps m6 and up, Taps that have centre holes. Plus for the most part I find it somewhat awkward to tap whilst the part is still in the mill/lathe. Personal preference. Plus when filming, it is extra awkward to try and tap whilst the part is in the mill.
@gabrielskec2646
3 жыл бұрын
Try to use concrete drill for broken taps and hard materials, just sharpen it like any other drill and watch the magic happen :) cheers
@gabrielskec2646
3 жыл бұрын
@@davidwillard7334 im sorry im not trying to be rude but im speaking from experience... Concrete drills have carbide, as i know carbide beats hss... Please try
@crpth1
Жыл бұрын
@@gabrielskec2646- Now that's a nice and simple tip... ;-)
@frankandstuff
Жыл бұрын
What are the dimensions of your piece of steel?
@artisanmakes
Жыл бұрын
Roughly 75 x 25 x 165
@TysonClancy-Jones
Жыл бұрын
Hey mate What size dovetail and is it 60°? Also, what size T slot cutter did you use?
@artisanmakes
Жыл бұрын
Just make it the same dimensions as the cross side dovetail you are intending to replace. For me this was a 60 degree dovetail
@TysonClancy-Jones
Жыл бұрын
@@artisanmakes thanks mate 👍
@i2c_jason
2 жыл бұрын
Great job!! I like the possibility of gang tooling...
@antonmursid3505
2 жыл бұрын
Antonmursid🙏🙏🙏🙏🙏🇲🇨
@AndrewSmith-qj5zv
2 жыл бұрын
What does dropping heated parts in lindseed oil do?
@artisanmakes
2 жыл бұрын
It gives the part a rust resistant coating. It's similar to seasoning a cast iron pan.
@yeagerxp
3 жыл бұрын
Excellent 👍👍👍. Thanks for sharing
@iamtheomega
3 жыл бұрын
8:32 steveohdee said he likes to hole the part in the other hand (rather than in vise) to get a better feel and avoid breakage....
@jaivigo
2 жыл бұрын
17:50 as usual on your videos, awsome job, thanks again.
@TheDistur
2 жыл бұрын
Looks real nice. I'd like to make a riser block for mine to "delete" the vise the tool post is mounted on.
@rengankrishnaiyer6912
3 жыл бұрын
Sir, could you share the drawings ?
@mealex303
3 жыл бұрын
Needed lots of oil b4 assembly but excellent content and love your vids
@woozhi9218
3 жыл бұрын
Nect up hand scraping all machine tools xd
@neffk
Жыл бұрын
As milled?
@danielernestogomez8534
3 жыл бұрын
Saludos desde argentina my nombre Is Daniel
@JesseSchoch
3 жыл бұрын
Seems like a tapered gib would have been worthwhile here. Thanks for sharing it!.
@artisanmakes
3 жыл бұрын
That is certainly something I'll be working on, but I thought it was just outside the scope of this video. Cheers
@lefrancoisjeanpierre3098
3 жыл бұрын
Perpendiculaire zero
@bemdusse7219
2 жыл бұрын
Zum anreissen nimmt man eine Reisnadel,die Schiebelehre ist dafür nicht geeignet. Man schlägt ja einen Bohrer auch nicht mit dem Hammer durchs Metall. Es gibt Gewindeschneideöl... Ansonsten saubere Arbeit.
@ajdogcurr1
2 жыл бұрын
good job. I plan to do the same thing including building a new tool post.
@lyteyearz5810
2 жыл бұрын
Fly cutting is so satisfying to me idk why lol.
@davidrivaz
3 жыл бұрын
Planning on putting them for sale?🤔
@everpastrana8354
2 жыл бұрын
Donde puedo conseguir ese tipo de brocas. Excelente video
@frogandspanner
3 жыл бұрын
gib has a soft g. Not to be confused with the brother Gibb.
@arenspringvloed9020
3 жыл бұрын
Aaaah. :) Feels so much better watching you breaking chips when tapping. Glad you managed to work around the broken tap!
@garlandtx10
Жыл бұрын
I've noticed when you've been tapping threads you hold the wrench at the end where you have the most leverage over the resistance on the tap... This is why you keep breaking them. You are at the very end of the leverage leg furthest from the fulcrum. You are pushing to far without realizing it because of this.
@artisanmakes
Жыл бұрын
Maybe, but I've since switched to good hss taps and haven't broken a single one. Snapped taps are pretty rare for me but it always happens with cheap carbon steel ones. Go figure :)
@White.Elemant
2 жыл бұрын
The endmill(s) used in this video seem to leave a rather rough surface, although I do not suspect it being too rough considering the fuction of the surfaces. Would that be because of the quality of the endmill, or maybe the bearings of the mill itself? Really love your videos by the way, very inspiring, unfortunately for me the local water company slapped me with a formidable bill, quite out of the blue, so no minilathe, mini mill or welder for yet another quarter 😔
@artisanmakes
2 жыл бұрын
Pretty much spot on there, the end mills that I used were just cheapo import bits and they work but they do give you less than stellar finishes. It is also a combination of being my first big project on the mill too to, so I was still learning the mills capabilities. Cheers, hope you can get into the hobby soon.
@WeCanDoThatBetter
3 жыл бұрын
Awesome work and a really cool improvement project! I thought about this too but too much other projects at the moment:) Thanks for sharing, the result is really amazing.
@artisanmakes
3 жыл бұрын
Thankyou. Really enjoyed watching your channel too. Especially the compound slide mods. cheers
@lefrancoisjeanpierre3098
3 жыл бұрын
Ya rien de droit
@cavemaneca
3 жыл бұрын
It's interesting how often I see people dedicated to their old mini lathes doing a similar project. The original just really is that poorly built. It's always serviceable at best, but leaves you feeling like something is lacking.
@artisanmakes
3 жыл бұрын
Cheers, truth be told, I don't have the space for a bigger lathe (well maybe big enough for a Sieg c4 but that would be the limit) and I find it really enjoyable to see how far I can push this lathe.
@cavemaneca
3 жыл бұрын
@@artisanmakes if the hobby of working on the lathe itself is as important as what you make with it, it's absolutely worth it to start with one of the cheap machines and do all of the updates and improvements yourself.
@AlIce_FPE_offcial
2 жыл бұрын
I'm curious to how it is performing after a few months? I have a project I'm planning that's including this. Just waiting and collecting material until then.
@artisanmakes
2 жыл бұрын
I can certainly say that after adding tapered roller bearings to the lathe, this is the best upgrade I have done to the mini lathe. The t-slots come in handy all the time and make the lathe very versatile. And the extra mass is noticeably more rigid. Even though its made from mild steel I have not run into any issues, just keep it well oiled and it performs perfectly. Cheers
@TABE-O
3 жыл бұрын
Thanks for sharing. Where do u get cold rolled steel from in Australia? I’m in Sydney.
@artisanmakes
3 жыл бұрын
I have been given some scap here or there in the past. I have found some luck with edcon steel recently. Great for hobbyists since they low a low minimum order and a great online portal.
@jacknissen6040
11 ай бұрын
T-slots seem very deep … ?
@artisanmakes
11 ай бұрын
they are standard sized m8 t slots
@metalmanglingmariner
3 жыл бұрын
What a great project. I must do this for my C3
@frostbitevinnie
6 ай бұрын
Looks like hot roll to me.🤔
@artisanmakes
6 ай бұрын
Probably is actually
@OtherWorldExplorers
3 жыл бұрын
When you were fly cutting the t-nuts do you recall what your DOC was? Cuz that look pretty damn good And did you make the fly cutter or was it purchased? I am new to your channel.
@artisanmakes
3 жыл бұрын
The highest depth of cut I achieved was about 0.8mm. these inserts are meant for the lathe, so I think I could get better results with some milling inserts. The fly cutter was just a home made job, just some carbon steel with a slot cut into it for a lathe tool.
@Pushyhog
2 жыл бұрын
im gonna get danny and his big mill to make this for me.
@artisanmakes
2 жыл бұрын
Certainly a worthwhile upgrade
@billofalltrades2633
2 жыл бұрын
Brilliant idea! Nice job.
@backyardmachinist
2 жыл бұрын
Have you found the steel you used for the cross slide to have caused any ware to the cast iron dovetail of your carriage?
@artisanmakes
2 жыл бұрын
Not at all, keept oy nicely oiled and I've had zero issues with it. Cheers
@billhamilton2366
3 жыл бұрын
I don’t expect your tool bits last very long when you are barely taking off the mill scale.
@artisanmakes
3 жыл бұрын
Are you referring to the DOC with the end mills or the fly cutter?
@scooby8567
3 жыл бұрын
FANTASTIC man😎👍👍👍
@nathanquinlan2719
3 жыл бұрын
A link to the carbide flycutter would be great. Seeing it perform it looks like a good purchase.
@artisanmakes
3 жыл бұрын
Cheers but the fly cutter is a joke made job that I made on the lathe and mill from some high carbon steel and a spare lathe tool.
@SgtCude59
2 жыл бұрын
I check the comment what size are your t-slot
@artisanmakes
2 жыл бұрын
These are standard m8 sized. There are drawings online that outline the dimensions for this and the t nuts
@SgtCude59
2 жыл бұрын
@@artisanmakes do have the link
@TABE-O
3 жыл бұрын
Carbide fly cutter looks good. Where that from please?
@artisanmakes
3 жыл бұрын
I made it on the mill and lathe from some 1" high carbon steel rod
@Tinman97301
Жыл бұрын
💯👍
@MrJzuz
3 жыл бұрын
Bro, you need a bandsaw.
@ChrisHarmon1
3 жыл бұрын
How much was the price of steel? I have a hard time finding stock for a good price
@artisanmakes
3 жыл бұрын
Including the cut charge I think I paid about $8 for it
@shaunkrawitz
2 жыл бұрын
Awesome work. looks like a huge improvement. Where do you buy your metal from? I just bought a mini lathe and am struggling to find a place to buy blocks of Alu and Steel. Any help would be much appreciated. Cheers
@artisanmakes
2 жыл бұрын
Might not be much help if your outside of NSW but I buy my stock from a material supplier called edcon steel. They have scrap bins of steel that they sell at discounted rates. Before I used them I bought most of my stock off eBay. Shipping is expensive though.
@shaunkrawitz
2 жыл бұрын
@@artisanmakes Thanks for the reply. Im in Sunshine Coast, so might be a bit far to get to your supplier. eBay is pretty expensive, but i might have to resort to it for now. Really enjoying your videos. Thanks!
Пікірлер: 283