Thank you Buck! I'm now learning how to do all the shit my husband won't bother with! I love it! Knowledge is power!😊😊
@waltergrady2501
14 күн бұрын
Thank you sir for the lesson
@estocadatx8172
Жыл бұрын
EXCELLENT - easy to follow. I can't wait to get outside tomorrow morning and try this out! Thank you.
@Buckwsr
Жыл бұрын
Thank you, and good luck.
@veim2406
4 ай бұрын
Feels like using an impact driver is over tightening the nuts. But I'm no expert.
@ricksculley6721
16 күн бұрын
Wheels are fine, belt is fine, cleaned out area around drive but wire is all slack at handle, how do you get that tight again? If I push manually front wheels are moving but cant do from handle. Thanks
@EstebanLozada-nj3sh
2 ай бұрын
Just what I needed to watch to troubleshoot my lawnmower. Well explained and easy to understand. Thanks
@resa33
2 ай бұрын
Great video, when I engage the lever to make it to forward, it locks up, if I release it, I can push it again, have you encountered that?
@rondab6390
Жыл бұрын
Thanks so much for this. I was trying to save some money so I went in myself and followed all of your steps to do this :) Very detailed and it helped. The engagement bar works, I check the gearbox and that also works, I grabbed my wet vac and vacuumed all the grass out that was under that flap to clear that….. I haven’t checked the wheels yet or the belts but… I’m doing one thing at time :) I grabbed the cable cord and pulled it a little….and when I did so, the wheels finally started turning properly. However, when I let the cable go the wheels stopped turning. It’s almost as if the cord has to be in a certain place. I had to tape the cable down in the right spot so that the wheels would keep spinning and work properly. Any suggestions on how to tighten the cable or how to replace it altogether?
@Michael-e1r3m
4 ай бұрын
Symptoms sounds like you need to adjust the cable up on the handle bar
@markrobertson8816
2 жыл бұрын
If drive pulley engages when motor running but slips when running with a new belt could the drive pulley be the cause, mower was made in 2009
@mnhiga
3 ай бұрын
Great video. It’s was a lot of help.
@randytorboli
Ай бұрын
does this apply to the Craftsman M270
@sjguy1099
Жыл бұрын
EXCELLENT VIDEO! VIDEO & SOUND, CLEARLY EXPLAINED EACH LOGICAL STEP, SHOW RESULTS. THIS IS HOW REPAIR MANUALS SHOULD LOOK! YOU ARE BETTER THAN THE WRITTEN REPAIR MANUALS!!! THANKS FOR ALL YOUR HARD WORK, PUTTING THIS VIDEO TOGETHER!
@paulmonk7820
4 ай бұрын
Does it matter which way you tilt the mower? 😮
@cheryladelmeyer8172
2 жыл бұрын
My new used mower goes too fast even on slow. Any advice?
@trylaterry3374
Ай бұрын
I turn the pulley by hand and my wheels do not move. At this point I don't think replacing belt will make a difference. HELP!
@Buckwsr
Ай бұрын
Does the transmission pivot and belt tighten when you squeeze the handle?
@trylaterry3374
Ай бұрын
@@Buckwsr yes
@dywildatheart
Жыл бұрын
Just wanted to thank you. I followed your advice with the same lawnmower. I did every step and all looked well. I took the plastic shroud off to get to the belt and the belt was off the pulley. So much crud had pushed it off. Put it all back together and runs great. Obviously I subscribed.
@Buckwsr
Жыл бұрын
Great job, David, fixing it yourself!
@michaelelliott3516
5 ай бұрын
Great video thanks
@randymemphis
5 ай бұрын
My Toro Recyle 22! The Front Wheels wont stop working! They stay on! I have adjusted the Tension many times but it wont turn off! what am I doing wrong
@tylerdibastiani8511
3 ай бұрын
Thanks for the video! Probably a dumb question but what drill attachment do you use to test the gearbox?
@Steve0885
4 ай бұрын
Adjust the cable
@Michael-e1r3m
4 ай бұрын
Good video I’ve got a craftsman RWD with a cable problem but to service it seems a little more difficult than these FWD models it doesn’t seem to have the service lid or door and it’s a newer mower then this one 7.0 Platinum series I believe
@TopGunMan
3 ай бұрын
The little peg that transfers torque in only one direction from the front shaft to the cogs was stuck and rusted in my case.
@713lopezf
Жыл бұрын
Great video! I replace the front cover and realized wheels stopped turning. I replaced belt but now experiencing the following- wheels do not turn when "belt keeper" is positioned correctly but wheels turn when right side of "belt keeper" is under belt or not inserted correctly. Can mower be used without "belt keeper" wire? Any help would be greatly appreciated!
@andrewbrown4952
4 ай бұрын
I have a 12 year old toro push mower that had the front wheels move but lock up and wont complete a full rotation. This happened after hitting a glass bottle in tall grass. Thank you for the video I will check all this tommorow
@Existntlangst
11 ай бұрын
Thanks! Had an issue with my Craftsman M320 RWD. Same troubleshooting steps and it needed a new belt.
@deanow4012
5 ай бұрын
great instructions .. removing that front belt guide wire can mess you up if you dont pay attention..and i could see it perfectly..and the power wheel hub tip was great.. metal and plastic doesnt mix for long. especially with the torque presented to that plastic.
@bobbhobb8393
4 ай бұрын
Oh when you pull it backwards you have to tip it? No wonder I was worn out today
@gail6904
Жыл бұрын
what happens if u accidentally move the GEAR behind sheel? does it have too be in a certain position?
@theHook-up
2 жыл бұрын
NICE ...
@lindadelagarza9858
Жыл бұрын
I have a self propelled toro lawnmower with Honda motor and I bought a new belt and it still don't go forward what can be the problem
@brentdenais7109
2 жыл бұрын
I have a brand new mower that pulls when you push that handle down but don't pull down . Right out the box . Think I'm going to send it back . I checked the video out everything good .
@tunahead7275
2 жыл бұрын
Hey Buck, another great video, and perfect timing for me. I'm trying to figure out why my Troy-Bilt mower isn't self-propelling quite right, and your video has helped me understand how the whole system is supposed to work, and where to focus my attention. Quick question... I've seen other KZitemrs suggest that you replace the blade adapter every time you replace the belt, have you ever found that necessary?
@Buckwsr
2 жыл бұрын
I've never replaced the blade adapter. If the blade adapter includes the pulley on which the belt rides, I could see some value in replacing it if it has worn down over time. Otherwise, I don't see the point in replacing it.
@tunahead7275
2 жыл бұрын
@@Buckwsr Thanks, that's good to know. My adapter does include the pulley, but it seems fine to me, just needed a little cleaning out with a wire brush. I think my problem is with the cable, because the gear box isn't rotating forward and tightening the belt like it's supposed to.
@Buckwsr
2 жыл бұрын
@@tunahead7275 okay, sounds like you're making progress. The cable may be adjustable and you could tighten (shorten) it a bit. Make sure there isn't built-up grass obstructing the forward movement of the gear box.
@tunahead7275
2 жыл бұрын
@@Buckwsr I was able to adjust the cable a small fraction of an inch today, by unthreading the cap at one end, effectively "lengthening" the cable housing and "shortening" the cable itself. It didn't help, the gear box still isn't rotating forward, and the belt still isn't tightening. The clutch lever on top of the transmission does move like I think it's supposed to when I pull the handle, but nothing else happens. I cleaned all the grass from the entire mower earlier. I'm thinking at this point I may need to just replace the cable, or there's something wrong with the transmission. The handle and the wheel assemblies seem fine, the belt is only about a year old and looks good. Any thoughts?
@asl2mckays
Жыл бұрын
Curious why you used your impact driver to remove most of the bolts (?) but on the under side you used a hand held handle.
@barrystoker9085
5 ай бұрын
Awsome video! This is the very same mower I have, so I'm ready to go outside to check these fixes. Thank you!
@jerryhixon6852
Жыл бұрын
My wheels will spin when I lift the front end off ground but when I set it down it don’t have the power to move it
@dennisbrown4966
Жыл бұрын
excellent video.thank you for the great information on lawn mower repairs. mr. brown
@sunflowermahea225
5 ай бұрын
May nit be high end, but they still want a pretty penny for them ...not cheap
@OKIEBUD
5 ай бұрын
Yes sir you taught things to look for my front drives been getting weaker so gona see if I can fix it… good video
@aaronjarvis4147
4 ай бұрын
Awesome video, helped me realize my belt popped off. I do have another question pertaining to this mower. Im a younger guy, and would like to speed things up. This mower adds another 15 minutes to my time compared to my standard push mower. Is there any way to speed this bad boy up a little bit? I dont want to win races, but id really like it to go a smidge faster. Thanks for any help!!
@Buckwsr
4 ай бұрын
Possibly increasing the engine speed might help, as long as you don't overdo it. Here's a video I did on that topic: kzitem.info/news/bejne/1HpsxWaXmmOnnKw
@liljoeii6091
Ай бұрын
I will have to check mine thank you for the video
@moneytyl.l.c.8285
Ай бұрын
Thank so much Buck!
@Buckwsr
Ай бұрын
Thank you.
@andrewmattie9713
4 ай бұрын
Beautiful vid, thanks for sharing.
@carlthornton3076
Жыл бұрын
Very Good!... #47 ✝ {8-12-2023}
@Danny-ju2ip
Жыл бұрын
Great thorough video. Much appreciated !
@caydenvlogs-mn1jo
Жыл бұрын
that engine is actually a briggs and stratton exi
@jarodcarpenter4628
Ай бұрын
Great video and explanation!
@TheMAC0876
2 жыл бұрын
Good video. Why does everyone keep taking off the pulley nut when you can just pull the wire guide off that is on the pulley? That is the easiest way to change the belt on the front pulley. No need to remove the pulley nut.
@dawnhoke3198
2 ай бұрын
Exactly
@danielfain5845
Жыл бұрын
Hey Buck what grade oil is in the self propelled gearbox ? 90w?
@Buckwsr
Жыл бұрын
Honestly I do not know....Poke around online, you'll find the info, I'm sure.
@gail6904
Жыл бұрын
what if the belt keeper is missing?
@williamjones3639
8 ай бұрын
Excellent tutorial video.
@MrBobbyfresh
Жыл бұрын
Helped me, thank you buddy
@kenniitran
Жыл бұрын
Thx for sharing video.
@Hamp205
Жыл бұрын
Thank you you just saved me
@Hiltonhead_70
5 ай бұрын
Good video. Thanks 👍🏽
@fancypelusa2863
Жыл бұрын
Good advise thanks!
@EdD-ym6le
2 жыл бұрын
Thanks for window switch replacement video on (my) 1998 Pontiac minivan you posted 5 years ago . Mine failed today - AutoZone will have the switch tomorrow and I had the AC serviced a couple months ago so I'm good . I found and changed the cabin filters probably for the first time , really surprised to find all that filter stuffed into that small out of the way hole hahaha .
@Buckwsr
2 жыл бұрын
Thanks, Ed, and good luck with the van.
@EdD-ym6le
2 жыл бұрын
@@Buckwsr AutoZone called this evening a day early / same day that they received it and I popped it in a bit ago so all's good 👍 I sub'd to your channel , Good Luck and God Bless you , your family and America .
@DougSivyer
Жыл бұрын
Great video Buck. My front wheels turn about half way and the lock up. I can pull the mover backwards and the wheels turn halfway again until they reach the lock up point. This is with the mower engaged or off. Any thoughts? I clean all the grass rope weed from the axel bar that connect to to front wheels so no obstruction that I can see. Any thought would be appreciated. I have a Toro 6.50 Recycler
@Buckwsr
Жыл бұрын
Hard to know without seeing it. I wonder if the engagement cable is adjusted properly?
@y002cjw
Жыл бұрын
Maybe the cogs are worn on the inside of the wheel.
@albertocarrasco7418
Жыл бұрын
Thank you very much well explained
@Buckwsr
Жыл бұрын
Thank you.
@SoeurnAm-w2m
Жыл бұрын
Good explanation
@rameshpersaud7131
Жыл бұрын
Great job TK U
@dvdtnnr
Жыл бұрын
Great video!!!
@littlecajun2241
Жыл бұрын
Thanks Buck.
@johnhurtado440
5 ай бұрын
good job.
@claudenobles779
Жыл бұрын
excellent...but remove the plug wire before removing the blade
@Buckwsr
Жыл бұрын
Well, okay, if you wish. But let's be honest: It is absolutely impossible for this engine to start up "accidentally" while removing the blade....for three reasons. First, with the control cable in the stop position, the flywheel brake is engaged, making it difficult to spin the engine. Second, with the control cable in the stop position, the magneto is grounded out, making it impossible for the ignition system to fire. Finally, breaking loose the blade bolt with a power tool will not get the engine spinning fast enough to start the engine. I simply have never seen an engine start "accidentally."
@claudenobles779
Жыл бұрын
@@Buckwsr wiel i got that advice from another lawn mower channel 🤔maybe they were mistaken. Regardless your advice on fixing the front wheel assist worked perfectly. thank you. subbed and belled
@Buckwsr
Жыл бұрын
Thank you so much, Claude. I don't want to sound like a know-it-all. It's very possible that in the days prior to all these safety features of the modern era, that removing the lead wire to the spark plug was in fact a necessary precaution. But understanding a little bit of how these machines work, I don't think I was taking too big a risk in my approach. Anyway, I'm glad your machine is back working as it should. And thanks for supporting my channel. Buck
@randysnedeker8629
Жыл бұрын
Very very helpful thank you
@Buckwsr
Жыл бұрын
Thanks, Randy!
@mikemarcus8676
3 ай бұрын
thank you so much
@Buckwsr
3 ай бұрын
Thank you, and good luck with your mower.
@chetg2924
10 ай бұрын
its all Birggs.
@Michael-e1r3m
4 ай бұрын
Briggs are great motors they’re even better for mini bikes
@jamesmills1825
2 жыл бұрын
Very good video
@Buckwsr
2 жыл бұрын
Thanks
@k9under
2 жыл бұрын
Thanks having a problem with my all wheel drive lawnboy sometime it will back up. then sometime the back wheel lock on going back only.
Пікірлер: 94