Thank you so much for this video! I will say that with a straw cleaning brush bent at 90 degrees could access and clean the holes in the bleach cup from underneath without have to take anything apart. Worked like a dream!
@jsuperman7672
10 ай бұрын
Yes very helpful. My mom has the same machine, just a different name. I took the back off , but didn't think to look up. I will clean that tray for sure and go from there, great video, thanks
@jnako4361
Жыл бұрын
Yup that’s exactly what it is! Sometimes if you have hard water or just corrosion, it can also block or creative build up in that little hole from the beach cup when the water gets flushed
@murraywest186
2 жыл бұрын
This fixed my problem thanks to the maker of this video
@toddworthley8780
Жыл бұрын
Thanks for the instructions on opening the top of this machine! I have the same model and your video is the ONLY one I found that shows how to do this. I had to replace the door latch/switch which you can see @3:41 in your video on the far right side. I may do a video on this part replacement. It is the only problem I have had with this machine in all the years I have owned it. I did give a good cleaning to the parts you mentioned while I had it open. Good video - thanks for uploading.
@jnako4361
Жыл бұрын
And thank you for identifying the issue and sharing with us in KZitem land!
@inay6484
Жыл бұрын
Thanks for the video! Very helpful 🙏🏻
@blurrr555
6 ай бұрын
Good description video
@DIYManiacJohnP
6 ай бұрын
Thanks for watching
@HB-tt1kn
2 жыл бұрын
👍
@therealrollaz
2 жыл бұрын
The "gunk" was probably fabric softener being put into the wrong place.
@hazelrah321
Жыл бұрын
Why would they design an overflow port to drain right into the back of the machine?! Couldnt a hose have connected it to the drain pump at the bottom? Astoundingly poor engineering!
@sonumonu5553
3 ай бұрын
This is so tjat after 2 or 3 years people spend another 900 and buy a new one 😮
@frankgiroux
Жыл бұрын
Thanks for that video! I have the exact same problem. You help me with my car, now with my washing machine! Thanks again! 😄 Have a nice day!
@DIYManiacJohnP
Жыл бұрын
Thank you so much for the kind words
@Lozzz76
2 ай бұрын
Oh my … this video is so informative. Sometimes people like me need to be told how like ABC 123 lol. Great content, thank you !
@DIYManiacJohnP
2 ай бұрын
Thank you for watching
@WiliamShattner
Жыл бұрын
I have the exact washer and same leak! Thanks!
@AnnetteRichter-b3f
Жыл бұрын
Thank You sooooo much-driving my crazy, I couldnt find it!!!! THANX JOHN!!!
@tessaih03
Жыл бұрын
I have same brand and same problem will try this method. Hope it works🙏
@mexps8093
2 жыл бұрын
Thank you! very helpful
@marcbarnard7268
2 жыл бұрын
Thanks buddy!
@juanmanuelmarquez4945
2 жыл бұрын
Very informative my dude!! Kudos!!
@mikebadilla6970
Жыл бұрын
Thanks
@robmead3130
4 ай бұрын
Thank you! Excellent video
@DIYManiacJohnP
4 ай бұрын
Thank you for watching
@gregorio4646
Жыл бұрын
I have “new” Krib Bling with no dispenser and it leaks 5 lbs of water every time I fill it about a few inches high, even if I fill it through the top door, machine unplugged. I guess it’s by the grace of God that it has not blown up in an explosive short circuit by now.
@jude4184
2 жыл бұрын
Any idea how to replace those inner inlet hoses? “/ I can’t get access to inside the back up top
@nombongobusakwe5423
Жыл бұрын
My washing machine is not spinning
@nombongobusakwe5423
Жыл бұрын
Showing E6 what happened
@devilsmustang2137
Жыл бұрын
Hi my washer is leaking from the softener dispenser, cleaned it out and still leaks, overflows. But I don’t even use it, I use detergent pods. Is there another solution?
@frankgiroux
Жыл бұрын
Check for dispenser dammage. Sometime, the thub "hit" the dispenser and it damage it. Plus, check if your thub is still centered. Mine is offset and the liquid barely fall on the edge of the thum itself. So, if the dispenser is damaged, the water comes out of it like splashing in every directions. That is what I had as problem. I was able to fix it, but you can easily buy a new one and replace it yourself. (I'm still trying to figure out how to center the thub though. Probably by turning the top of the rods that support the thub. (Seems to have some threads at the end of the rods or maybe a nut... story to follows) 😁
@melsay1
Жыл бұрын
Disconnect the softener plug, like in the vid, only the one that connects to that.
Пікірлер: 34