More detail needed: 1) how do we know the coating is ready to buff since different coatings flash at different time periods? 2) What does the coating look like, or is it still sticky when you start buffing? I can’t seem to find out this information, and I don’t think I need to take a class to find out. Your channel isn’t the only one that leaves out this important information.
@rodolfolopez2081
3 жыл бұрын
Yes once you buff off it still there (at least on cars) and every ceramic Coating has diferent time to buff it so check the instriccions, once you finish the job should look very glossy and once you wait forncure time will look even more Glossy.
@darrellbrown8547
2 жыл бұрын
Great tip on tapping
@adventures223
2 жыл бұрын
Great job I do have a suggestion its a lot of work but a clay bar works best
@jcbrady8299
4 жыл бұрын
I would have like to have seen how you detail around the chrome letters and the vinyl graphics. I have the same boat and getting into those areas is painstaking and tedious work. Does anyone have an idea how much this would cost if done by a Pro?
@davidcooper1213
4 жыл бұрын
We normally charge 100.00 a foot for mild correction and ceramic coating.
@glenndaugherity6187
2 жыл бұрын
@@davidcooper1213 After watching this video I can see why you charge 100.00 an hour ! Very tedious work for sure. How long does a ceramic coating last ?
@fishydubsfishing6516
2 жыл бұрын
What was the final reading on the gloss meter when you were done
@lionelzepeda5860
Жыл бұрын
Did you use your alcohol mixture on the whole boat?
@gm1937
2 жыл бұрын
GREAT video; the 3M imperial product is no longer available. What 3M or other product would you recommend?
@TurnerMobileDetailing
3 жыл бұрын
Great vid man! Can I use a compound/polish combo like Meguiars M105/M205 on gelcoat? Also, do you not ceramic coat the whole hull? Or do you somehow put the boat on stands that would expose the whole hull?
@glossbaus2336
2 жыл бұрын
You can try meguires but you will need to have a very abrasive version to cut through gel coat oxidation. We only ceramic coat the sides of the hull, the part in the water usually gets bottom paint, or we just keep it natural. Although some customers may insist in the whole hull being done as well.
@maggie1767
2 жыл бұрын
@@glossbaus2336 my don’t you do the bottom?
@vincentdemontigny4682
Жыл бұрын
@@maggie1767 cause it won’t oxydized . It’s under water . Only surfaces that are exposed to uv light and air need to be protected
@Nextlevelmarine
4 жыл бұрын
Are you using special lights to apply the coating
@glossbaus2336
4 жыл бұрын
Yes we use a scan grip light, but you can use many others that are more cost effective.
@Nextlevelmarine
4 жыл бұрын
Do you have a link? To the light
@charleschapman5838
3 жыл бұрын
What materials do you use specifically and where can i get them. Sorry if i missed something or its in the subscription somewhere. Im kinda new at this.
@glossbaus2336
2 жыл бұрын
Amazon is your best bet for marine polishes.
@TriDaddy
4 жыл бұрын
I like the closing - But the website listed the premium products for "installations" or the professionals which goes against what is being told. Whats up with that? Also how much product was used for this 25ft boat? Thanks!
@glossbaus2336
4 жыл бұрын
We offer products for both installers and for the general public. We used 100ml for this boat.
@daveb7206
3 жыл бұрын
how much does this cost to do on a 25 foot boat?
@glossbaus2336
3 жыл бұрын
Really depends on the boat but roughly 2000$
@seanscannell5163
4 жыл бұрын
Ameture hour, I thought I was going to learn something. Guy uses big words to make it sound good.
@brianfitzpatrick7451
Жыл бұрын
Your spelling is as bad as your comprehension. He uses the proper terms. You just don’t know them, Dummy.
@siman264
2 жыл бұрын
That gel coat would never in a million years be free of oxidation from your compounding. The polishing oils almost immediately fake a glossy finish. Even after an alcohol wipe those polishing oils are deeply embedded and won’t release for a week minimum
@glossbaus2336
2 жыл бұрын
Maybe for you, but not for us. We use specialty compounds and polishes and remove all polishing residues with a panel wipe before we apply ceramic coating. So if that was the case the panel wipe would wipe away these oils that are giving the fake shine.
@siman264
2 жыл бұрын
@@glossbaus2336 not correct gel coat is extremely porous and oils can take weeks to be flushed out in the water or evaporate in the sun
@glenndaugherity6187
2 жыл бұрын
Please do a video Simon we want to see !
@justinmw5113
3 жыл бұрын
Starts by showing how bad the gray part was but never shows what it looks like with the ceramic on it.
@glossbaus2336
2 жыл бұрын
Lol well if you get it shiny with polishing, its going to be just a tiny bit glossier with ceramic, not a massive difference, the difference is in the quality of the polishing.
@davidhoar75
5 жыл бұрын
That boat is gleamin! Great video, very technical and informative. BAUSS.
@363pr271
4 жыл бұрын
Great video.
@fredriggin5132
3 жыл бұрын
with the rub rails a clean cotton rag with some acetone cleans them right up you just gotta be careful not to touch any gelcoat with the acetone cause it'll take your wax right off
@jvalle9978
2 жыл бұрын
Wish you would’ve showed the ceramic coating on the aft of the boat where the paint is darker and not the white paint. That way we can see the difference.
@glossbaus2336
2 жыл бұрын
The difference is in the polishing. Apply ceramic coating to an oxidized portion it will look nearly the same, apply ceramic coating to a heavily cut polished surface, it will enhance the look slightly, the ceramic is more of a sealer then a magic coating that makes dull things shine.
@dennishingsbergfilms
3 жыл бұрын
great video, ceramic coating demystified!! any tips how you remove previous waxing that may have been done on boat? cheers thanks again
Пікірлер: 39