i think this is the best video but i think you should shade more light on differences between constant voltage driver and constant current
@4philipp
Жыл бұрын
We need a driver that connects existing LED lights to poE, and adds an external switch. Remote computer control might be a nice touch too. Sigh, a man can dream. I think such a Driver would push poE into the consumer market and power up DIYers.
@LeonardoLeo-jw2dx
23 күн бұрын
Thanks for the well detailed and simplified explanation, could you please tell us what simulation platform you were using in this video ?
@amitkumarsingh5822
2 жыл бұрын
Very good explanation
@jojotech4615
3 жыл бұрын
Sir new subcriber from Philippines
@theweb2guy
3 жыл бұрын
Thanks for subbing!
@ww07ff
7 ай бұрын
Great explanation!!!
@ruru.904
5 ай бұрын
sir how can i make led driver using dc to dc boost converter and dc to dc buck converter in the same circuit .I mean how can make the connections between this dc converters and LED
@drory1
Жыл бұрын
very good explaination
@jitendrabakliwal7494
3 жыл бұрын
very nice sir
@theweb2guy
3 жыл бұрын
Thanks and welcome
@ahmedmohsen89-tx3hj
9 ай бұрын
what is the benefit of the diode between the inductor and the positive output and is it shotky diode or not ? thanks❤❤❤
@farisk9119
2 жыл бұрын
Thanks I found the link. Cheers
@lambertax
3 жыл бұрын
In the constant current schematic you give, the mosfet is in a linear region (bad efficiency). So it will heat much more than in the constant voltage circuit. How do we have the best of the 2 world?
@miqbal7032
3 жыл бұрын
How to design LED constant voltage source in everycircuit
@ashokkumarkanithi7279
3 жыл бұрын
What about the power factor of the AC supply? Also Electrolytic capacitor (EC) reduces the life time of the LED Driver, so how to remove EC? but the output should be constant.
@theweb2guy
3 жыл бұрын
Good question. The buck converter has a very goof PF. For the capacitance you can use a brand like Nichicon, which has a good life. Normally engineering is a balance between cost and performance.
@OthmanAlikhan
Жыл бұрын
Thanks for the video =)
@cantkeepitin
2 жыл бұрын
Hi, why do we have the diode, the inductor and cap at 12:23 ? Isn't the cap huge in comparision with the large ohmic resistor of 154kOhms?
@miqbal7032
3 жыл бұрын
How to create hysterises curve in everycircuit app for Schmitt triger
@nitesh_thakur3798
Жыл бұрын
I want to make dimmable led driver
@putra6106
Жыл бұрын
Let there be sound....
@ashwin372
2 жыл бұрын
What's RMS ?
@SunilKumar-me4cs
2 жыл бұрын
Rms means " Root mean square".. Simply we can say for easy understand an " average "
@sarathsamarasinghe2462
Жыл бұрын
Sorry, it’s too advance for me. Meanwhile it’s very quick. Thank you.
@abdulfaheem38
3 жыл бұрын
Hello I'll be thankful if you help me regarding power supply of my led Cob led which I got is flipflop type and its of 100w and on data sheet it mentioned 3500ma current and 34v but problem is ,I am not finding exact same output driver but someone suggested me to use two 50w and one 20w driver parallely connented (1500ma+1500ma+600ma=3600ma) by doing this it's exceeding 100ma current and even when I test voltage of that driver it show 48v... Will it be safe to power up the led or it'll damage the led? connecting driver parallely is a good idea to get my required current? On data sheet it's mentioned Forward current =3500ma Peak forward current (duty 1/10@10ms) =5250ma please help
@theweb2guy
3 жыл бұрын
I don't think this is a good idea. If you want to use drivers in parallel, you need to make sure they are all exactly the same voltage and have reverse voltage protection. If not the drivers will be damaged. 48v is quite high and will possible damage the LED. This doc will give you some idea on the issues with using drivers in parallel - www.cui.com/catalog/resource/download/current-sharing-with-power-supplies.pdf
@abdulfaheem38
3 жыл бұрын
Thanks sir... If you don't mind ,can you share me your mail id...I'll mail you data sheet of my led..upon that can you suggest me best power supply to that led?
@abdulfaheem38
3 жыл бұрын
Sir can I take 36v 5amp SMPS and connect it to dc step down module and adjust current to 3.5amp and use it...will it work?
@theweb2guy
3 жыл бұрын
I would not advice that. SMPS do not normally maintain constant current which is what you need for the leds to be uniformly bright.
@abdulfaheem38
3 жыл бұрын
Then what you will advise me sir... Neither I am not getting driver nor I can use with SMPS... Can you advise me please
@farisk9119
2 жыл бұрын
Hi, what is the on line link of free simulator please? Thanks
@theweb2guy
2 жыл бұрын
www.falstad.com/circuit/ incase others are also looking.
Пікірлер: 38