LINK TO HEADLIGHTS 👇🏻 👇🏻👇🏻👇🏻👇🏻👇🏻👇🏻 auxito.com/products/ford-fusion-led-bulbs-2013-2017?ref=oqq49zdb4x&variant=41029409210520 USE CODE - “AUTOHEADZ” FOR 15% OFF!
@MakerMurph
Жыл бұрын
Thanks for the video! Ordered using the code!
@AutoHeadz
Жыл бұрын
@@MakerMurph Very much appreciated Sir. Thank you for the compliment!
@DrNotJC
9 ай бұрын
“You should be able to do this in about an hour.” Video starts at sunrise and ends in the dark. Thank you for this, I’ve had to replace mine twice, it’s such a pain. There are videos saying there’s an easy way where you don’t have to take the bumper off, it’s not easier, trying to twist the light into place is only possible if you have tiny hands.
@AutoHeadz
8 ай бұрын
Yes! People say it’s easier…..for 2% of the population maybe.
@Alki777
6 ай бұрын
I can, I've done a headlight change in 25min. You don't need to remove the bumper. Remove the top except for the farthest screw/clip and only the ones below the headlight assembly and then pull the housing out just enough to access the rear where the bulbs are. 25 minutes for both is all it should take.
@markgally731
4 ай бұрын
Holy crap.... you're a better man than me and you must really like your brother-in-law. My daughter has the exact same car and was at Midas....told me it was $120. I said , leave we'll do it ! Mostly labor... After watching you. She's going right back tomorrow !! I am not changing Jack ! Great job with the video !!! I'm glad I watched....but no way ! ☮️
@vamshikrishnamoogala
Жыл бұрын
Thanks for the instructions. I successfully installed in my 2015 fusion. One thing to do when installing low beams is to also replace the daytime running lamps with white LED lights. Else, just the DRL’s will be yellow and LED’s white. I think they are 925’s and are located next to high beams .
@goose1498
6 ай бұрын
did you replace the h7 highbeam lights with led? If so what brand did you use that fit the harness?
@huntermonkhouse6301
2 жыл бұрын
Thank you for the helpful video! The lights that came with my fusion were atrociously dim, and thank goodness you made this video, spent about 1: 30 with my dad and we were able to switch em out for brighter ones! Cheers!
@AutoHeadz
2 жыл бұрын
That’s amazing. Im pumped you were able to use my video to help you out. Take care man!
@MattFields02
Жыл бұрын
What year Fusion do you have? Considering replacing mine on a 2016 Fusion but interested if the results vary on different model years.
@nikola8646
Жыл бұрын
Only ford Engineers would do such a bad design ,To replace the headlight bulb you need to remove the bumper , imagine you are on the road and need to replace the bulb
@AutoHeadz
Жыл бұрын
It’s absolutely absurd
@at-t1489
9 ай бұрын
They need to change this like it’s so stupid and inconvenient
@maikolas5901
3 ай бұрын
Yea bro what about Mercedes? Same shit
@nikola8646
3 ай бұрын
@@maikolas5901 Mercedes is luxury car , Ford ain’t
@joud360
7 күн бұрын
Did the same job but just removed the clips under the wheel arch, as well as the top screws and clips. Allowed me to pull the top part of the bumper away and remove the headlights. Took about 20 minutes pretty side.
@johnmcmanus129
Жыл бұрын
Thank you from Dublin Ireland, what a nicely paced, fully informative tutorial, I wish I'd found this video yesterday,
@AutoHeadz
Жыл бұрын
Hey man, I really appreciate you saying that. 🙌🏻
@rivalstorm120
Ай бұрын
Would like to add for anyone watching, get adjustable LEDs. Where they sit factory with round bulbs, to aftermarket LEDs, you need to change the rotation of the chips to be centered at 9 and 3 inside the projector. If you put them in just how they are, they will not project correctly. Make sure the brand you buy, has adjustable LEDs. The ones in this video is not adjustable. Auxito does sell adjustable ones but these specific ones are not...
@pawlinski74
Жыл бұрын
These bulbs are very well made thats for sure they look quality
@pboyle99
Жыл бұрын
One thing not mentioned in the video is that the length of the new bulbs is greater than the originals. So you cannot put the bulbs in the socket in the same place as the original on the driver side. I tried to do that, but I realized that 1) it would not fit because it would hit the rim of the dust cap hole and 2) the leds would not be vertical. So, I had to install it with the stem facing downward. Actually, that is correct for the driver side. I tried to install the same way on the passenger side, but now the bulb would hit the rim of the hole since the alignment is different on the passenger side. I decided to install it with the stem of the bulb facing towards the driver side of the vehicle. This puts the leds at 120 degrees off vertical. It's not ideal. Elsewhere, I saw instructions that the orientation of the led can be changed on the bulb with a small screwdriver. Once I recover from this installation, I will pull the passenger bulb again and try to fix the led vertical alignment.
@R8EDN
Жыл бұрын
this is hilarious because i’m literally in my living room recovering from 2 days working on this mess 😂😂😂
@sethjohnson6753
Жыл бұрын
Does yours flickers when u use the turn signals? I installed every light bulp with led.
@pboyle99
Жыл бұрын
@Seth Johnson No I never see them flicker when using the turn signals.
@maverick392cid
2 ай бұрын
Literally takes me less than 10 minutes to get the bumper off and the headlights out. But i just drop the bumper down from the front end, I dont take it completely off the car.
@NoNameNoViews
2 жыл бұрын
Hey man thanks for the video! Used your link and got some. I had some silver star ultras I was going to put in before a big road trip. But I wasn’t sure if I should use halogens again. Thanks for the easy steps!
@AutoHeadz
2 жыл бұрын
Haha! That’s awesome man! I’m so glad I was able to help. It’s a bit of a process but definitely better than paying a ton of money for the shop to do it. I really do appreciate the positive feedback. It means a lot. Take care 🙏🏻🤙🏻
@thedevilsmilk
Жыл бұрын
I thought you’d like to see this video. Ford fusion headlightbulb replacement 2013-2020 on the “The Driver Mod” channel. No bumper removal literally 6-8 mins a light. Hope this helps your brother faster in the future.
@jared123123
Жыл бұрын
This will be long , apologies. But yes you CAN change your bulbs without taking bumper off, you can take the headlight mount brackets out. The larger led lights all fit different depending which model too It is VERY tight, potentially extremely frustrating and you’ll beat up your hands but Also couple screws (10mm bolt under the hood stops that you pull off) that are extremely easy to drop into engine bay then your gonna be in a worse spot. After going through all this on couple fusions , I started taking the bumper PARTLY off, Basically remove all the screws and clips along the front / fender liners. Pop bumper off slightly, disconnect some connections, and then there is two bolts under each headlight, removing those will allow you to slide headlights completely out after unplugging . Take off majority of headlight mount too ofc. Sounds like a lot but it took me less time overall due to ease of changing all lights at once when it’s out. The amount of time it CAN take using the other method along with higher chance damaging something too forcing stuff in small space. Changing the 194 led running lights at same time recommended as well. Or they will be on and mixing with the light from leds. If that bothers you anyways.
@ephrimkuzmitski709
Жыл бұрын
Most leds won't fit without taking the bumper off I tried, the fan on the lights gets in the way.
@waynenation678
Жыл бұрын
I have a 2017 SE and you don’t need to remove the bumper to change the bulbs. For me I just want to change the whole headlights
@scottsnyder5192
Жыл бұрын
Not sure what year you are working on. Mine is a 2019. Hate to break it to you but you DO NOT HAVE TO TAKE THE FRONT END OFF!!!! I replaced mine, high and low beam just using my hands. Takes some time but it can be done.
@AutoHeadz
Жыл бұрын
Not with the 2014’s my man. Trust me. Good move getting the 14.
@RellyOhBoy
11 ай бұрын
Seems like Ford kept screwing around with the front of the engine bay on the early 2nd Gen Fusions. I had to change the low beam bulbs on my 15 Titanium about a year or so ago because the oem halogens finally crapped out. Not a difficult task just frikkin tedious. If I recall, I only had to remove the top fasteners and the wheel well fasteners to pull the top of the bumper cover out just enough to get the light housings out. I believe Ford slightly modified the forward upper brace on the 16 and up to allow just enough room to fit your hands in there to change the bulbs without all the dumb shit. I think they purposely shoe-horned the damn motor and all the components into the engine bay to make things harder for DIY'ers to work on hoping to force a visit to the stealership service dept.
@AndrewNobleOfficial
2 жыл бұрын
Here here here and here 🤣 Great video man!
@AutoHeadz
2 жыл бұрын
Lol, thanks man.
@pawlinski74
Жыл бұрын
why you dont show how to change the high beams
@harveycastro4676
Жыл бұрын
great video, just drove my girlfriends fusion and realized the headlights are horrendous, going to add these in for her using this video! are these the bulbs that would be the blinkers tho? if so, id like to get some switchbacks in case you have any you can recommend? im thinking of doing all the lights in the front for her, low/high and fogs too (not sure if it does have fogs tho). would greatly appreciate any links or anything you may have! and again, great video!
@AutoHeadz
Жыл бұрын
Thanks man. So here is the link. If you want to swap out everything they sell a “whole package deal” just look at the top of the page you click the link and one of the options should say “whole package”. Use code LOVE4U or AUTOHEADZ for a discount. Enjoy! Auxito H8/H11 LOW BEAM LED LIGHTS - auxito.com/products/ford-fusion-led-bulbs-2013-2017?ref=oqq49zdb4x&variant=41029409210520
@rodneyjones3987
Жыл бұрын
THANK YOU SO MUCH U SAVED ME TIME AND MONEY
@AutoHeadz
Жыл бұрын
My pleasure. Thank you for watching man!
@NunyaBidness590
9 ай бұрын
Great video, well done.
@AutoHeadz
9 ай бұрын
Glad you enjoyed it
@R8EDN
Жыл бұрын
i will say… if you’re changing high beams on the 2015 Model, do not get the H7s with the heat sink at the end. Almost impossible to fit because the light housing is aligned oddly. Find an h7 that’s 1-to-1 with the original bulb.
@WealthWiseNavigators
Жыл бұрын
Great observation, i was doubting on this part of the conversion! Thanks for the tip!
@jared123123
Жыл бұрын
Not only that the ones with the added ballast etc before the plug in connection also have much larger fans which some will physically not fit inside the crappy metal bracket clips that hold the high beams in
@kildozer2012
7 ай бұрын
A set of AUXBEAM GX fits in with about 2mm of clearance after installation. The biggest pain was getting the clip to go back in since you have to install the light with the clip wrapped around it. I couldn't find any needle nose pliers at the time, but I would assume that would help a lot
@freeeric80
4 ай бұрын
Thanks for posting. Any idea about the lifespan of those LED bulbs? I'm due to replace my factory bulbs and am considering an upgrade. However, since changing the bulbs is more complicated than the invasion of Normandy, I'm not looking to do it again for a long time. Will the LED bulbs last? Any idea if they are DOT legal? Also, are they so bright that other motorists will be flashing me thinking my high beams are on?
@AutoHeadz
4 ай бұрын
The focus I installed them on is still shining bright. I’d say at least 5 years
@pawlinski74
Жыл бұрын
I recieved these h7 bukbs but i dont know if they are with adapter or not can You send apic or link how those adapter look like ...would be helpful many THKS
@AutoHeadz
Жыл бұрын
Hey man that’s great. What exactly do you mean by adapters? Happy to help.
@pawlinski74
Жыл бұрын
@@AutoHeadz Im confused becuse H7 turbo high beams You say they need special adapters i recieved bulbs only plus some little extension cables but the socket in the fusion for h7 is wierd i havent taken down the front bumper yet but i would like to be prepared if i miss something Many Thanks
@cjjj749
Жыл бұрын
Great design Ford…
@AutoHeadz
Жыл бұрын
Lol…don’t know what they were thinking with this one.
@samuelzukauskas8233
2 жыл бұрын
Great video
@AutoHeadz
2 жыл бұрын
Thank you.🤙🏻
@Darth.BlaXon
9 ай бұрын
Thank you!!!!
@AutoHeadz
9 ай бұрын
You are very welcome!
@donaldubdegrove6763
10 ай бұрын
Do you ever have your headlight come on whatever you have leds low beam tell it happens too 2016 ford fusion
@dukephantomx
Жыл бұрын
Great, next thing it would require removing the engine to change some oil, I own a 2015 titanium and this shit is pissing me off just to replace some damn bulbs and I have to remove the whole bumper which would definitely make it loose.
@neilrwoods
2 жыл бұрын
thankyou for this, im now thinking why on earth did I buy a Mk5 Fusion / Mondeo ( UK ) , such a job just to change a few bulbs.
@AutoHeadz
2 жыл бұрын
Absolutely my pleasure. Good luck with the install.
@pawlinski74
Жыл бұрын
hi ive puchased the h7 for my ford fusion directly from china but im not sure they come with adapters ,,so my quick question is what kind of adapters do i need for my 2015 ford fusion and how do they look like for those h7 bulbs many thanks
@ryanhernandez4074
Жыл бұрын
I have an issue of flickering when turning on the blinker. Does anyone else have the same problem?
@RHKH
Жыл бұрын
Hi Ryan, I have same issue, but after researching it seems that we need something called "anti flickering harness"
@ryanhernandez4074
Жыл бұрын
@@RHKH I tried 2 different brands with the anti flickering, however it still flickers so I’m thinking of HID’s.
@hailnt
7 ай бұрын
@@ryanhernandez4074 I have the same issue. Have you tried the HID yet?
@michaelmijatovich8983
Жыл бұрын
Did you change the high beams also plus other lights in the headlamps? Like turn signals and so on
@edwardbuffington53
Жыл бұрын
You don't have remove the front bumper to put headlights bulbs in. I changed mind out to led in 30min. It's other videos showing how to. My family owns a collision shop
@user-qn2id8xe8o
5 ай бұрын
Good job
@AutoHeadz
5 ай бұрын
Thanks man.
@danhernandez483
2 жыл бұрын
Thank you!
@AutoHeadz
2 жыл бұрын
No..Thank you!
@zooski3x219
7 ай бұрын
So you’d have to pay them more. But there’s a way faster way faster way. You don’t have to remove the bumper
@AutoHeadz
7 ай бұрын
Not for this year
@Purplestar666
Жыл бұрын
Hey I just installed these on my 14 fusion but I wasn’t aware that the projector lens in the housing isn’t really compatible with leds since it creates a small shadow in two spots (since led lights go outwards instead of forward). Did you have this problem or no ?
@AutoHeadz
Жыл бұрын
No I didn’t have this problem. Significant improvement over stock. May have a different beam pattern but I don’t really care about what the beam pattern looks like as long as I can see down the road better.
@bdubberz
Жыл бұрын
Low beams on the stock housing are projector. High beams are the only bulbs that use reflectors.
@maximilianorosas1865
Жыл бұрын
Qué modelo de lámpara leds lleva? Para las luches y los camineros abajo? Gracias
@AutoHeadz
Жыл бұрын
Here it is. Good luck man. If you use the code “AUTOHEADZ” you get a nice discount. Auxito H8/H11 LOW BEAM LED LIGHTS - auxito.com/products/ford-fusion-led-bulbs-2013-2017?ref=oqq49zdb4x&variant=41029409210520
@nickrindlisbacher6553
9 ай бұрын
I bought these headlights , I have a 2014 ford fusion se...they don't fit
@T-Pocalypse
Жыл бұрын
Hey, I bought Auxito's also for my 16' Ford Fusion but they have ballasts on them. Do I put the ballasts inside the dust cap too or is there wa spot I can run the wire outside the dust cap? What about the fans on the LED's? Are they okay inside the dust cap with the fans running on the back of the bulbs inside with the dust cap on?
@AutoHeadz
Жыл бұрын
Yes. The will be fine inside the dusk caps. I would suggest doing it that way. I have my F150 set up like that and it’s worked great. Hope that helps and good luck!
@T-Pocalypse
Жыл бұрын
@@AutoHeadz I was just worried they would get hot on a long trip somewhere but there was enough room inside my housings thankfully. I appreciate you getting back to me. I installed them yesterday and they look great. Thank you for the walkthrough video - it helped me a lot.
@AutoHeadz
Жыл бұрын
That means a lot. Sorry I took so long to get back to you. I went through my comments today and realized I missed a bunch of notifications. Take care man.
@T-Pocalypse
Жыл бұрын
@@AutoHeadz No problem at all, I don't expect anyone to check their comments the same day or even within a week - we're all busy doing something. ✌Thank you again.
@michaelwoods7458
Жыл бұрын
Is the installation the same on a 2020 ford fusion
@AutoHeadz
Жыл бұрын
No Sir. The install is different for that year. Quiet a bit easier actually for the 2020.
@casheighty8
2 жыл бұрын
Did you need a flicker module?
@AutoHeadz
2 жыл бұрын
Nope. All plug and play
@AutoHeadz
Жыл бұрын
@J H No issues at all. Plug and play.
@hunter4972
Жыл бұрын
I’m new to working on cars and I looked it up but I couldn’t get a good answer online, if I change out my halogen bulb for my low beam but not high beam will my high beam still have that yellow look to it. And if so is there anything I can get to make it to where they’re both led?
@AutoHeadz
Жыл бұрын
Hey man! Yes. They are separate bulbs and can both be replaced with LED bulbs. The high beams will look yellowish until replaced with led high beams. The high beams are held in with a clip. These are the high-beam LEDS. 👇🏻 www.auxito.com/collections/h7-led-bulb/products/auxito-h7-led-bulb-50w-10000lm?ref=oqq49zdb4x&rq=yr_2014~mk_Ford~md_Fusion~tm_Standard%20Trims~ml_High%20Beam
@tch632
Жыл бұрын
3 minutes into this video.... OH HELL NO!
@AutoHeadz
Жыл бұрын
Hahahahahahah!!!!! You’re not wrong. It’s a pain in the ass.
@tch632
Жыл бұрын
@@AutoHeadz : I found this technique to be a possibly better option: kzitem.info/news/bejne/zqaDzWisnIuTd6g
@randymorgan3556
2 жыл бұрын
Maybe spin the ratchet like a wrench instead of ratcheting when it’s unnecessary to save your arms.
@AutoHeadz
2 жыл бұрын
Great tip. Thanks!
@MadMan_123
Жыл бұрын
@AutoHeadz swivel head ratchets are nice you can spin them like an old fashioned speed rachet. Also cordless ratchets are nice Milwaukee makes them for less than a regular snap on 🤣🤣
@joepaul1763
Жыл бұрын
Ridiculous to change headlight bulbs
@AutoHeadz
Жыл бұрын
I know. It’s insane.
@MaaZy_
2 жыл бұрын
You can access from the top
@AutoHeadz
2 жыл бұрын
No you cant. Some model years you can but not this year, I assure you.
@MadMan_123
Жыл бұрын
I love my Milwaukee colorless ratchet. Break em loose and zip em out
@insideout69
Жыл бұрын
dope ass fucking video thanks alot
@AutoHeadz
Жыл бұрын
Hahah! Thanks man!
@MrVontar
Жыл бұрын
These cars original headlights suck, especially if your windows are tinted. I need to upgrade my lights soon, don't wanna kill anyone lol
@AutoHeadz
Жыл бұрын
Hahahaha! Good move man!
@Dcthetruth85
Жыл бұрын
Ford should be ashamed of themselves for making it difficult to get to the bulbs.
Пікірлер: 117