That is very elegant and well done. You obviously have some serious Fusion 360 skills. I’ve also been playing with a Lee APP
@andrewrocc
Жыл бұрын
No i'm a beginner with Fusion...but very pasionate....
@JeffinTD
11 ай бұрын
I did print a case feed adapter for mine, along with the cartridge specific tubes so I don’t have to adjust the jamb nuts. Didn’t do the handle though, as I built an air cylinder auto drive.
@rmattson61
2 жыл бұрын
Please ignore my previous entry. Seems my phone IE didn't want to display it. I had to turn off some security settings. Sorry.
@andrewrocc
2 жыл бұрын
Because the video is not allowed for the children...
@francored4166
2 жыл бұрын
Fantastiche animazioni e fantastici gadget
@andrewrocc
2 жыл бұрын
Grazie troppo gentile....Fusion 360 è un programma fantastico...
@CristianoMagrini
Жыл бұрын
Perfect
@wasino1000
2 жыл бұрын
Che meraviglia Andrea..... e fantastici i feeders che immagino tu abbia costruito?!
@andrewrocc
2 жыл бұрын
Ciao si i Feeder sono un progetto nato a fine 2017 quando mi sono comprato la prima stampante 3D.....sono contento che in tanti lo usano mi hanno scritto in tanti o per avere un aiuto per montarlo o per qualche pezzo personalizzato...insomma fa piacere....anche il disegno della maniglia l;ho fatto ieri sera ed è già su thingiverse per chi se lo vuole fare a casa...
@wasino1000
2 жыл бұрын
@@andrewrocc Oltre che un genio sei anche molto generoso! 🙏 Quindi i feeders funzionano ancora a tutti gli effetti senza usura o logorio da tempo?
@andrewrocc
2 жыл бұрын
@@wasino1000 Genio non direi proprio...generoso si e pure un po' coglione...con il feeder ci hanno guadagnato qualche soldo in parecchi meno che me....però rimane la soddisfazione di svariati ricaricatori in giro per il mondo che mi hanno scritto contenti di come vanno i feeder...
@MrRuben0076
6 ай бұрын
ciao Andrea, davvero impressionante il lavoro che hai fatto, quanto costerebbe il Feed completo per la app lee?
@MrRuben0076
6 ай бұрын
Che dies consigli per il calibro 9x21 sulla lee app press? Ho provato con quello lee 9x19 ma fa tanta fatica a decapsulare e ricalibrare. Lubrifichi o bossoli per caso? Grazie mille
@andrewrocc
6 ай бұрын
Ciao io da più di 10 anni uso i dies del 9x19 senza problemi...però al giorno di oggi puoi trovare il sizer direttamente del 9x21....lubrifico i bossoli con la classica miscela di alcool isopropilico e olio di lanolina mutuata dalla ricarica delle cartucce da fucile (che se non lubrifichi inchiodi tutto)...con le progressive a mio avviso è meglio lubrificare almeno eviti un inutile sforzo che ti può andare a coprire altre problematiche che senti a mano quando ricarichi....
@MrRuben0076
6 ай бұрын
@@andrewrocc grazie, ricetta? Che proporzioni?
@Kennyy212
Жыл бұрын
Do you have the stl file for the tube adapter to your lee app press? Have both your bullet and case feeder prints which are awesome, but need to connect the drop tube to the actual tubes on the press.
@andrewrocc
Жыл бұрын
The parts you need is the final adapter to the Lee bullet finger? or for the case?
@freddyxx
2 жыл бұрын
complimenti Andrea, ho già realizzato un bullet feeder e sono soddisfattissimo. mi accingo a stampare un case feeder, ho notato che hai aggiunto una prolunga al contenitore per aumentare la capacità di bossoli. avrei bisogno di modificare il supporto (stand) per adattarlo al tubo da 1" della Dillon, ti posso chiedere il file di Fusion360?
@andrewrocc
2 жыл бұрын
Scrivimi ad andrea.roccati@gmail.com
@galick5454
Жыл бұрын
Do you happen to have the schematic for your single auto case feeder you used for lee app?
@andrewrocc
Жыл бұрын
Is a semplified version with no Pwm....so basically you will have a 12v inlet then at the positive (red wire) you will connect the positive of the motor (red wire) and the brown of the inductive sensor. At the inlet negative (black wire) you will connect the general switch....then atthe switch outlet you will connect the blue wire of the sensor so it will be correctly powered. Now you have to pilot the motor with the sensor: just use a 12v relay with NC and NO function....connect the negative (black wire) of the motor at the NC pin and the Com pin to the switch outlet (negative). Then you have the black wire of the sensor the SIGNAL....you have to connect this wire to the relay coil and the other coil exit to the switch outlet.... So now you have the entire wiring controlled by the main switch and when is on the motor runs because the relay is Normally Closed....when the sensor is triggered by a case or a bullet the Signal will excite the relay coil and the relay became Open...so it interrupts the power to the motor and it stops... Is a really simple circuit you can't get wrong with this... Just use a PNP NO 12mm 3wire inductive sensor and you will be fine....
@dubillo
Жыл бұрын
hola, que marca y modelo es la prensa esa de recalibrado? muchas gracias
@andrewrocc
Жыл бұрын
Lee App....hasta l'uevo
@RogerLoUSPSA
Жыл бұрын
do you clean your brass before or after this process?
@andrewrocc
Жыл бұрын
After...i use the App for decapping...then ultrasonic with dishwasher soap and after dry them tumbler just to polish the brass brand new...but really with the first stage the primer site is perfectly clean as well
@oleksII1903
Жыл бұрын
What lubricant do you use for slider to work so fast?
@andrewrocc
Жыл бұрын
Nothing..just clean
@agostinomazzotta2134
Жыл бұрын
ciao ho visto anche il progetto della regolazione altezza del bossolo per la app .. sarei curioso di provare a settarmi cosi la mia app... ho trovato il link del progetto della maniglia .. hai altri progetti per app?
@andrewrocc
Жыл бұрын
Ciao...onestamente non ancora perchè con i progetti sono fermo da un po' perchè non ho tempo....ammena mi rimetto seriamente cerco di fare qualcos'altro di utile, per ora ho da finire un comparatore per cartucce da fucile per vedere la concentricità della palla e poi vorrei fare una pressa intera monostazione...ma questa è solo una idea per ora...nessun disegno fatto....se tu hai bisogno di qualcosa ne possiamo parlare vedo se riesco a disegnartelo
@agostinomazzotta2134
Жыл бұрын
@@andrewrocc ma il progettino della rotella in 3d che usi per sistemare l'alzo dei tubi per bossolo quella rossa con il sostegno grigio per il mono tubo per capirci :)
@vittoriodavide9123
Жыл бұрын
Sarei interessato a questi accessori
@andrewrocc
Жыл бұрын
I disegni sono gratuitamente disponibili su Thingiverse...se lei ha una stampante 3d li puo' realizzare....io li disegno ma non per venderli(altri lo fanno)...
Пікірлер: 34