Leo Bodnar are a great company to deal with,( I have no connection with them other than as a very satisfied customer). I rang them with an obscure question which they answered immediately, then must have thought of some extra useful info for me and called me back unprompted some time later. This sort of extra mile service is sadly rare these days, so I feel they deserve a thanks for going an extra mile. I use my dual output Bodnar to lock my Pluto on 40MHz, and my LNB on 25MHz, for QO100. Best regards and thanks for great content, Chris Wilson in Shropshire.
@user.A9
2 жыл бұрын
You have the best audio on KZitem. Have you done a video on your production setup.?
@TechMindsOfficial
2 жыл бұрын
Thank you! Not yet, but in the future I might :) thanks again
@sagebrother
2 жыл бұрын
Very useful video and certainly an easier option than swapping out the "as shipped" TXCO chip
@thisisus.504
Жыл бұрын
Magically clear instructions. Thanks very much!
@photonthief
2 жыл бұрын
What an awesome piece of kit! Thanks for sharing!
@BrianHall
2 жыл бұрын
This is awesome. I'd love to see how to calibrate an Airspy R2 using your GPSDO (maybe you could add that to the same video where you calibrate an SDRPlay). I love this channel!
@bulthy1958
Жыл бұрын
Brilliant , thanks really got me out of trouble . Not seeing PW made think keyboard playing up till I looked at help files!!!!!
@joefrancalanza9995
3 ай бұрын
I use the dual Leo Bodnar 25Mhz for the LNB and the 40Mhz which i am going to use for the Pluto for the QO-100 DATV Portsdown transmitter....
@VK3TWO
2 жыл бұрын
I use my leo bodnar for my IC-9700, and several other GPSDOs for Pluto's, WSPR, IC-7610, microwave gear.
@caramba10
2 жыл бұрын
I miss the old days of building PLL based receivers to lock to the BBC Radio4 200KHz transmissions.
@caramba10
2 жыл бұрын
@@JxH It is now, it was moved from 200KHz in 1988 (When I said the old days I meant really old days LOL).
@laverdanick
2 жыл бұрын
When I worked there, a daily task was to measure the drift on the 200KHz transmitter against 60KHz from MSF Rugby using an Evershed Chart recorder. Both MSF and Droitwich used local Rubidium standards, but MSF was also referenced to the Caesium standard at NPL. All the broadcast standards are now ultimately referenced to GPS.
@caramba10
2 жыл бұрын
@@laverdanick I think I recall those chart recorders, were they the pen and red ink ones?
@ra3apw
2 жыл бұрын
As alternative way - good 10 MHz OCXO as reference for PLL with two isolated 25 MHz output - one for LNB and the second for Pluto. Good frequency OCXO stability more than enough even for digital modes. Especially useful for the place with limited access to open sky for GPS antenna.
@gammaleader96
2 жыл бұрын
Especially since the overall frequency accuracy isn't the primary concern as long as it is stable.
@ra3apw
2 жыл бұрын
@@gammaleader96 Correct. OCXO's Allan deviation is really good as 2.3E(-11) for 100s tau - see link www.ra3apw.ru/wp-content/uploads/2019/10/OCXO_AllanDeviation_1.jpg
@ra3apw
2 жыл бұрын
@@JxH Frankly speaking I do not see a big fundamental difference between 10$ and 20$ for OCXO purchase, On my new board for ADALM Pluto I use 10 MHz OCXO from CTI (with preliminary ADEV checking) as a main reference signal and as an option I have a dedicated input for connecting an external 10 MHz reference signal, for example, from LeoBodnar GPSDO mini. The main problem was to get a clear 25 MHz signal from PLL with minimal phase noise degradation. Lesson learned - don't do VCXO inside Xilinx CPLD...
@gammaleader96
2 жыл бұрын
I use the dual channel one for my QO-100 station. It generates 25MHz for the LNB and 40MHz for the Lime SDR mini I use. It works very well, is super stable and starts up very fast.
@roba2440
2 жыл бұрын
I have the dual channel one as well, what settings did you use? the closest I got was 45MHz?
@gammaleader96
2 жыл бұрын
@@roba2440 This combination isn't really a standard value that you can simply type in. I actually had the same issue of only getting 45MHz in combination with 25MHz. With the help of the Leo Bodnar support, I could get some manual PLL parameters, that achieve the combination needed. You can use these parameters: GPS: 390625 N31: 4 N2_HS: 6 N2_LS: 8192 N1_HS: 4 NC1_LS: 30 NC2_LS: 48 Make sure these match: f3:97656.25Hz fOSC:4.8GHz Just type them in manually from top to bottom, worked first time for me. Hope this helps :)
@roba2440
2 жыл бұрын
@@gammaleader96 Worked a treat, thank you very much
@gammaleader96
2 жыл бұрын
@@roba2440 You're welcome, glad I could help :)
@AG7SM
2 жыл бұрын
I have the dual output GPSDO, and I use it primarily as a reference source for my SunSDR 2 DX.
@TechMindsOfficial
2 жыл бұрын
Thanks for sharing this information, I’ve always wanted to try a SunSDR! Do you think the SunSDR really needs an external reference? Can you notice a difference without it? Thanks
@AG7SM
2 жыл бұрын
@@TechMindsOfficial Honestly, I'm using it more because I'm obsessed with precision regardless of necessity. The SunSDR is a brilliant platform with great software. I do see a difference when I turn the external reference on and off, but not on the order you were seeing with the Pluto. There are other reasons to use the external standard -- having multiple SDRs using the same reference allows you to do things like using phase differences to determine signal direction and the like. But mostly I did it because I could.
@TechMindsOfficial
2 жыл бұрын
That’s what’s the hobby is about, doing it because we can. :) thank you for your reply, appreciate the info!
@ninjauser-d2k
9 күн бұрын
hello Im trying to use the one using bladerf im unable to lock it. need help
@user-un4wo1hj4p
7 ай бұрын
Hello all, i get leo bodnar mini gps . For me nil, not running when put my adalm pluto on external clk, ok for internal, if i can have help for the config. i use adalm pluto and sdrconsole. when put external clk on config, i have no rx, no tx. my pluto is an rev C.
@cristi8732
Жыл бұрын
I have installed the GPSDO module on my Adalm Pluto in order to improve stability when working digital modes on QO-100. I have followed the instructions in this video, connected the GPSDO to the Pluto clock plug, used the Mini GPS Clock configuration utility to program it to 40MHz output, then ssh-ed in the Pluto with the Putty and programmed it to listen to the outside clock. With the SDR console connected and the mini gps clock utility, I am switching off and back on the 'enable output' option but it makes no difference, the frequency does not change at all. In the Console SDR settings under Callibration I ticked the option 'enable updates' to no avail.
@user-un4wo1hj4p
7 ай бұрын
i have the same problem, but for me no rx when swithing on external clk
@ManuelPinner
Жыл бұрын
I have one of these, like it a lot because I use with SDR Angel Software,
@aquahood
10 ай бұрын
Can you link together a hack rf to another hack hf via out to the in on the pluto as I have one of the temperature oscillator that you can plug directly into your hack r f board so then can I take that out the clock out and put it into my Pluto to take advantage of the clock in the Pluto as well as in they hack rf1 and will they be coherent at that point?
@muratcankarakoc7628
Жыл бұрын
In order to back Adam-Pluto into internal clock, is it enough to type the following command? #fw_setenv refclk_source internal and do I need to set external clock like "" or 10000000 ?
@kainkamote917
Жыл бұрын
Do you know if the output can be split and go to multiple devices if you had multiple SDR that can take clock input?
@AndrewMurphy8383
2 жыл бұрын
can you show how to use the leo bodnar gpsdo with sdrplay please
@TechMindsOfficial
2 жыл бұрын
Sure, I’ll make a video 👌
@AndrewMurphy8383
2 жыл бұрын
@@TechMindsOfficial thanks keep the videos up like them alot
@jbreezy3146
2 жыл бұрын
Q. Is the gpsdo needed if I just want to scan Frequencies?
@alexdelchini2802
2 жыл бұрын
Do you know if the mini Leo bodner is good to lock the frequency drift on a Icom 9700 Alex M7MEX
@gammaleader96
2 жыл бұрын
It should be perfectly fine yes. Just keep in mind, that the GPSDO outputs a square wave so you might want to add a fitting lowpass filter, depending on what your radio expects. Also make sure that the amplitude is right. Other than that it should be capable of generating the reference for whatever you want.
@alexdelchini2802
2 жыл бұрын
@@gammaleader96 thank you for the update👍
@TechMindsOfficial
2 жыл бұрын
Take a look here: www.leobodnar.com/shop/index.php?main_page=product_info&products_id=352
@8thspirit
2 жыл бұрын
Amazing
@ManuelPinner
Жыл бұрын
DATV Reception on a Adalm Pluto SDR,
@copycarvers
2 жыл бұрын
I think plutosdr will be able to transmit signals for GPS spoofing too right?
@gammaleader96
2 жыл бұрын
That is less a question of the hardware (most somewhat capable SDRs with TX functionality can do that) but more a question of the right software. I don't think there is an off the shelf solution for the Pluto. Which to be honest is a good thing, since you can cause an immense amount of trouble by doing this anyway. Even mWs of power can have way more range than you want it to / that you can control. If you want to spoof some GPS thing, rather go the software way of simulating the whole receiver instead of generating a fake signal. ... which is counted as terrorism in most regions of the world ... just saying.
@copycarvers
2 жыл бұрын
@@gammaleader96 I am a master's student and studying GNSS Spoofing in a controlled lab environment
@gammaleader96
2 жыл бұрын
@@copycarvers Good luck and I didn't try to offend you or anything, I just wanted to make sure you are aware of the dangers, since there are people out there doing stuff like this to spoof with some stupid mobile games and stuff. ;) For the HackRF, there is a pretty well documented GPS simulation workflow available, if you want to go this route. :)
@copycarvers
2 жыл бұрын
@@gammaleader96 actually being a student I can't afford hackRF right now and looking to explore different options. And I understand :) thank you
@razvanfatu6513
Жыл бұрын
B O D N A R
@ATOMSHAMRADIO
2 жыл бұрын
Nice
@M0UAW_IO83
2 жыл бұрын
Bod*NAR*
@TechMindsOfficial
2 жыл бұрын
Yup I realised my error after upload. Shame on me
@JTelecom
Жыл бұрын
show de bola
@rasputinputin8103
2 жыл бұрын
LEO BODNAR, not Leo Bodmon. You have been doing these mistakes a lot lately.
Пікірлер: 58