FINALLY, A REAL COMPARISON EXHAUST VIDEO. THANK YOU!
@Andrew-tl9gk
3 жыл бұрын
I think the original one is way better because it is more silent. Greetings from the city.
@SANCEZZ88
3 жыл бұрын
☺️😉 good one. I don‘t like to drive through your city. And it‘s not really loud compared to other (older) bikes before EURO4. It‘s just more bass and dirty sounding.
@simonecorradin9504
4 жыл бұрын
Is it with catalytic converter? Nice vid man
@SANCEZZ88
4 жыл бұрын
Yes, it has a catalytic converter and its street legal.
@fabiankranz5810
Жыл бұрын
Hi, sounding nice!!! Is it getting annoying when driving longer / is it too loud? And do you feel any power decrease with kat and db-killer installed? thanks!
@SANCEZZ88
Жыл бұрын
Hi, it is sounding nice, depending on weather and temperature. The exhaust isn‘t loud but has a nice deep sound for the driver. I didn‘t notice a power decrease. I would buy it again, if I had to decide again.
@AntonioLopez-gk7wm
Жыл бұрын
te hace una vibración en la caja del filtro de aire? como un rrrrrrrr .... y al acelerar en marcha que también se aprecia sobre las 4.000rpm?? llevo el mismo escape y en el video en el ultimo segundo cuando grabas el deposito, se aprecia también ese rrrr que viene del filtro de aire, quiero saber si seguro también te lo hace y si es normal...
@SANCEZZ88
Жыл бұрын
Yes, that's the case for me too. I often noticed that when starting at traffic lights or when idling, the noise of the air filter has also changed with the exhaust change. No negative effects so far.
@AntonioLopez-gk7wm
Жыл бұрын
@@SANCEZZ88 y en marcha sobre 3.500 rpm - 4500rpm al acelerar escuchas como un clicliclicli que viene tambien de la zona del filtro/escape??
@tristanleite2611
4 жыл бұрын
Did it require any remapping or computer flash??
@exothermal.sprocket
4 жыл бұрын
If you want to actually remove all the ridiculous restrictions, YES!! Otherwise don't bother doing anything with the OEM stuff.
@gianmarcosilva
4 жыл бұрын
Hi, what do you use on the lambda probe thread? it seems you put grease or something...nice video! thanks
@SANCEZZ88
4 жыл бұрын
I use copper paste/grease to prevent all the screws from corrosion.
@gianmarcosilva
4 жыл бұрын
ok,thanks, another question.. do you changes any copper seal near the flanges? i’ve heard to be changed (in fb discussion) but in the video I haven’t seen those parts..
@SANCEZZ88
4 жыл бұрын
You don‘t need to replace the sealing. But you should check if it‘s leaking. I replaced the sealings later, because i used a torque-wrench to adjust the screw torque on the flanges. But if you use the original torque, the flanges will destroy the sealing, because the design is different from original.
@gianmarcosilva
4 жыл бұрын
SANCEZZ88 thanks very much! the manual says 20Nm (for the OEM) what’s your suggestion?
@batsyt9113
4 жыл бұрын
Hi! Do you know how to remove db killer on this leo vince? Have the same and really dont know how to do! The btr screw is welded... Thanks
@SANCEZZ88
4 жыл бұрын
Just use an allen key, it's easy. But I don't see any reason to do that, it would be to loud while driving. I don't recommend it. Or do you want to ride your motorcycle with ear protection?
Пікірлер: 19