I have a great respect for the guys who take so much time on mobile installs whether it’s for competition or daily use, not a lot of room to work with considering vehicles and some times can become frustrating. Me personally, take the extra meticulous mile on my base station. Very cool install Mr.Miller and that’s a clean suburban too. 73
@Tony-rl2fr
3 жыл бұрын
If 204GC is here with a positive comment, then as far as I'm concerned, you're legit. Subbed, thanks to good content and 204GC.
@GroundControl204
3 жыл бұрын
@@Tony-rl2fr Thanks a lot, but in all honesty BBI is Mr. Miyagi and I’m just Daniel son.👍🏻😂73
@420commslink
3 жыл бұрын
Yeah me too, between Ground control and BBI those guys keep me on youtube lol. Waving a hand Luke and Mike👋🏻
@commslinktv
3 жыл бұрын
Good analogy 204GC🤣
@bblod4896
3 жыл бұрын
Never thought about using a backer plate but I'm just running a Wilson 1000 on the truck roof. Thanks for the installation class Luke, have a good Sunday.
@TheRdeanpeek
3 жыл бұрын
extremely appreciate your time and effort in putting this project on video...thanks ever so much...!!!
@BklynRulz
3 жыл бұрын
Can't say enough about all your vids but this one might just be your best. Can't wait for the rest of the mobile install vids. Thanks for taking the time to show us your methods. 455 NYC
@jhen291AL
2 жыл бұрын
This Video Mr BBI WILL BE YOUR CEMENT LEGECY, by far it's the one single most IMPORTANT VEDEO you have to date, TRUELY THANK YOU MY FRIEND!!!😊
@luckymunkey77.
3 жыл бұрын
And now I’m beginning to understand the whole grounding issue. I’m subbed
@aaronson2540
3 жыл бұрын
DEFINITELY NOT FIRST, BUT ANOTHER FINE VIDEO MR. BBI.... 👍🏼👍🏼👍🏼..... AND YES BITCH I AM A FAN.....😂😂😂
@philhall6778
3 жыл бұрын
Oh man....learning time for me...love these..dr.phil says hello from illinois..love the burb...rolling radio station....
@donaldlee1525
10 ай бұрын
Your video is very educational. I wish I could get someone to do this to my vehicle
@wildintrudertechnology
3 жыл бұрын
Nice clean job! Makes me miss my 1990 model suburban. Just awesomeness brother!
@electromechanicalstuff2602
3 жыл бұрын
Just a 4*16 so they can hear me 10 miles down the road. Lol my factory 955 can talk that far from mobile to mobile. My straight 8 can go a LITTLE bit further. Lol
@EricTechstuffs
3 жыл бұрын
NICE ! Can't wait for part 2 !
@joeythompson3579
3 жыл бұрын
Bonding straps size matters Sounds like radio porn 🤣 keep the videos coming
@Brandon_B.
3 жыл бұрын
AWESOME DUDE REALLY APPRECIATE YOU SHARING THIS INSTALL VERY INFORMATIVE & HELPFUL WHEN YOU ARE DONE PLEASE PROVIDE A MATERIAL LIST
@joekane5029
3 жыл бұрын
Its Saturday I'm sitting in the basement watching this and not doing my "honey do " list 🤣...how long can I go before I'm busted
@408SPLKINGS
3 жыл бұрын
If you just do your honey, your honey will forget your honey do list.
@Joe_HamRadioGuy
3 жыл бұрын
Looking good.... Dynamat is great have it on my doors for stereo sound.
@FirstHandBlind
3 жыл бұрын
The only question I have right now is..... how did you get your logo to display on your head unit?
@brianolmstead6
3 жыл бұрын
Thank you for this. I've had to deal with a ground pigtail to the puck before. It causes the feedline to radiate, affects SWR, and can cause RF microphone feedback. A quick fix is to clamp split ferrite beads over the coax and slide them up to where the ground pigtail exits the coax. Looking forward to the next installment!
@tyronetbrown2152
Жыл бұрын
Keep up the Good Work,.Grave Digger,.660 State of Maryland,.10.6, Reading this Mail.......
@DK5ONV
3 жыл бұрын
Awsome job done, Mr. Miller! Happy sunday from SW.-Germany
@robertperry8973
3 жыл бұрын
I am amazed to know that there is actually a Big strapper who is willing to give the world a glimpse into that world of CB radio that is as mysterious and interesting 🤔. I am so blessed to have your channel
@gabrielM1111
2 жыл бұрын
Im almost certain your suburban's entire body and frame is all factory bonded by standard welding and bolting not glue like you keep saying. Use multimeter and youll see nearly all the metal in your vehicle is at the sane potential to your main and add on batteries (if said batteries are properly/heavily grounded to engine and chassis) Only possible resistance will be doors if plastic washers are used in hinges. I think only bonding that would make a noticeable difference is 1 strap on each door. Id put ferrite beads on all your car audio speaker wires and rca cable. For magmount its important to a solid connection between the foil film under the magnet and the internal antenna ground.
@James-we2gx
Жыл бұрын
I did get some knowledge from this video. Thankyou for making it for us all. Get’s me thinking. Thankyou, Mr. BBI.
@randallroberson8635
Жыл бұрын
Thank you for all your tips and experiences.
@hardhead7056
3 жыл бұрын
That antenna sings because it is made of flat bar stock. Ive not seen the antennas that use round stock for thier coils sing. Personally.
@petersannicolas8949
3 жыл бұрын
Loving the BBI mobile looks good BBI
@garybarnstable9569
3 жыл бұрын
Thank you for install. Answers alot Questions. Piece of metal what type of metal aluminum steel or what sorry just asking.
@kf4cei
Жыл бұрын
I love your videos. Technical stuff, but with some badassery for us Gen-X hams and bench techs. Pretty sure I'm not the only one who blares heavy metal and grunge while running LMR400 through my headliner.
@ehayes5217
3 жыл бұрын
Great vid, very interesting; however, for a newcomer like myself, it'd also be great to see a more "basic" install, that is, one showing just the simple stuff that a newbie wud need to know on a FIRST install--thanx!
@joeyemmert3519
2 жыл бұрын
What kind of vehicle you have depends on setup and if you decide you want TALK and RECEIVE or astetic talk and receive
@joeyemmert3519
2 жыл бұрын
Even a big setup can look ugly but if done right will look as if it was supposed to be that way in the first place
@J20J20
2 жыл бұрын
I love it dude please keep them coming 639 break break 🇨🇦
@LarryGivens
3 жыл бұрын
Dr J Fresno Cal. R.I.P. helped me build my mobile & he was just like you , no shortcuts. Thank you for keeping this lost art going Mr BBI you big duck.
@CarrotDugTooDeep
3 жыл бұрын
That first whip antenna that you mentioned was made by Motorola is actually branded by Motorola and Harris, but is made by PCTel. It is not 0-6 meter, it is 136-174, 380-520 & 7/800 MHz. It is a 1/4 wave on VHF and is very wide-banded and works very well. They are what we use on our system for all 4 bands.
@BoxBuilderIdaho
3 жыл бұрын
Ah they made. Two or three versions of the same antenna man. I have the 2-meter version myself. It works okay
@KINGLOWNESS
Жыл бұрын
"Si Bueno" gets me everytime 😂😂😂
@rhoemberg1969
3 жыл бұрын
🔥 Thanks Mr. BBI for tbe adult beverage ! Why is it when I am hanging around The Dark Side .... I feel like building, breaking or burning something down ???????☠💥🤬 🧯⚡🔥🍻
@randyfox4611
3 жыл бұрын
Really a great video BBI and more to follow.......cant wait. Thanks as always for being a great teacher. The Drag'NFly in tennessee said that.
@lawrencekb5zzb551
2 жыл бұрын
Excellent video Luke. One quick question. Where do you get the connectors to make your "ground lug" to the shield side of the rg-393? Do you make them yourself?. Tnx and 73
@glenroycorbin9347
3 жыл бұрын
Thanks Bbi for a very informative 👍 video great job Greetings from Barbados 🇧🇧 Aggitator out
@SunriseCrawlers
11 ай бұрын
Friends like Rick are valuable
@towerman75
9 ай бұрын
The only thing I don't understand, for the grounding is super, but at the wattage you talked about running, and the electronics that is involved in todays vehicles, how do you keep from getting into that ??
@BoxBuilderIdaho
9 ай бұрын
Well the thing that we've worked out is the RF will stay on the outside of the vehicle for the most part. Some of the higher frequencies get blocked out by the just simple things like the tent that's in the windows. You ever noticed how your garage door opener sometimes won't work if your vehicle is just a certain way and there's too much window tint in the way.. that helps put a good grounding system a little bit of properly placed ferrite the wires that go to and from the electronics aren't residents of the RF just kind of passes right on by. I really wish in modern vehicles they would do Twisted leads on most of the electronics that would help so much
@AmateurRadio
3 жыл бұрын
once you see flames its too hot. the flux has burned. better to use a little less heat. nice vid.
@joecarty8579
6 ай бұрын
I’m planning to do an install on my Toyota pickup but my biggest concern is Airbags, not sure if that’s ever been an issue for anyone. I would be happy with 500w carrier so relatively qrp compared to what you run. Ps the power/temp rating on your feeder is when it’s in free air for cooling, watch out if you cover it.
@BoxBuilderIdaho
6 ай бұрын
I have not had a problem with the airbags it's just me though let's see what other people have to say
@root7205
3 жыл бұрын
The only thing I do differently with the mat is use a roller. I find I usually get a better bond by rolling the mat instead of just using finger pressure. And how well do those small antennas work for 2 meter?
@TimberTramp
Жыл бұрын
Could you have run the ground strap between the reinforcement rods and the sheet? Maybe along one end for one strap and the other end for the other…? Just thinking aloud and I seriously know a little less than nothing so take it for what it is worth….-noob
@maninthevan53
3 жыл бұрын
wow nice underbody coating , just bought a 2017 tahoe and thinking of a good underbody coating , the standard is dodo , already seeing some rust
@561ENTERPRISE
Жыл бұрын
Impressive BBI. Looking forward to the bonding videos. 73's
@earlblackjackmartinjr5750
3 жыл бұрын
All I can say is GOOD GRIEF. 👍
@George_S.G
3 жыл бұрын
Never stop learning !!!!
@joerowland7350
3 жыл бұрын
Thanks this just in time as I'M about to do my 4x4 I bin fix up I have a breedlove 2 inch thick strap n the mat n I cut a plate To sandwich under the 8 inch I have bounded most of the truck Tube bumper's rock sliders roll bar Hood bed but I'm going to try your threaded rod
@arildoaparecidocosta5729
3 жыл бұрын
Top hein parabéns guerreiros bazuka Foz do Iguaçu pr Brasil
@FlightJunkie
3 жыл бұрын
Just a Note to THANK YOU for taking the time to share. Over the years I have done a number of Installs (HACKS), as compares to what I have just watched. My next vehicle will incorporate what I have just learned. Thanks Again
@TimberTramp
Жыл бұрын
Watch AvE’s take on star washers and other mechanical type “lockers”….I believe, in short, he found everything is virtually worthless except “nordlock” (I think they’re called) washers…they’re kind of a cupped washer with spiral type tooth on the washer… he has a good take on the situation! Good on the Loctite!
@andrewevanoff1192
3 жыл бұрын
What are you going to run in there? The antenna looks like a CB antenna. You mentioned several alternators and additional batteries. What power will you be running? I don't know much about CB but isn't it limited to 4 watts on AM mode? Do you need a special license for high power? BTW, I've been running mobile HF for close to 20 years. Currently I use an Icom IC-7000 and a Tarheel 75A antenna. I agree with you about grounding and bonding. I did similar things in my 4Runner but the most important was to bond the exhaust to the frame in several places. Also, I bonded the body to frame and the rear axle to frame (to keep any RF current from pitting the rear bearings. Unlikely but possible). Prior to that, after I installed the radio and tried transmitting on 40 meters while driving, the check engine light came on and the vehicle went into limp mode (greatly reduced power). I'm glad I had an OBD2 reader with me and was able to clear the codes and get home. It would have been a major trouble if I didn't have the scanner with me. We were way out in the middle of nowhere. I highly recommend having one if you run a high power transmitter. Bonding the exhaust fixed the problem and the codes never came back.
@tonymcclendon-hobbytime7727
Жыл бұрын
AWESOME BUILD
@charlesbaker5309
3 жыл бұрын
BBI I guess you are running a Mr Cooley antenna? What inch is the bottom shaft? What length shaft do you think is best on a suburban? And why? Do you like the predator 10 k antenna? I know I'm asking alot of questions but I'm trying to learn something, thanks man, CBJ NC got down
@adi-hg2zt
3 жыл бұрын
Thankyou mr bbi for all the videos you upload always a pleasure to watch a master at work.have a great day sir and all the best to you and your family.take Care coz we care.From the UK.
@321CatboxWA
2 жыл бұрын
Cool Man ! Bonding next . .. Giggidy
@MrNobody-gi3gj
3 жыл бұрын
Love it luke!! Awesome job and always great content
@johnnywood8082
3 жыл бұрын
Mr BBI, I need a 4 pill to run with my 955. Can you accommodate?
@TimmonBreenBabyGirl
2 жыл бұрын
That stuff you call glue is called sealer. It doesn’t glue body panels together. It seals the joints that are spot welded. I’ve been in the factories that make GM trucks and there are an army of robots that spot weld the bodies together.
@dougpoulton5544
3 жыл бұрын
Now you can get on the interstate and ask all the truckers "can you hear me now"?
@bgvan37
2 жыл бұрын
Great video.
@ubergeek318
3 жыл бұрын
So is the reason you made the ground straps with the torch is because the solder pot takes to long to heat up?
@ryanpaaz
3 жыл бұрын
Newer Burban. Curious to see if there will be any problems with the the computer controlled bits of the car. Sure he'll keep the ride from being an RFI mess, but it may just be a case of overload and proximity.
@BoxBuilderIdaho
3 жыл бұрын
I'm looking forward to finding this out myself. But I'm sure there's not going to be any problems that I can't overcome with either grounding or ferrite choking
@joshp2424
3 жыл бұрын
NICE VIDEO BBI THANKS FOR THE 411 KEEP THEM COMIN 73 FROM THE MINI GRASS
@joekane5029
3 жыл бұрын
I can't wait for part #2👏👊
@chrishuber4853
3 жыл бұрын
How much of this is applicable to a 10 and 11 meter setup? I'm guessing all of it, but is there anything you would do differently for a 10 and 11 meter. I'm not even clear what band this video is for because of the antennas you use. Anyways, sorry for the dumb questions, but I'd rather ask than screw something up. Thanks so much. I love your videos. This info is priceless.
@frankwc0o
2 ай бұрын
Do you know of anyone in SoCal that does great mobile installations? thx
@Mr_Clean
Жыл бұрын
16 pills some good conditions and a hot truck! 💪
@tracystolp5357
3 жыл бұрын
Nice clean job 👍
@Dallas-Rife-UDX-347-Tennessee
3 жыл бұрын
It didn’t show up close exactly how it mounted to the puck under of the headliner, dang !! Nice set up 👍👍. I’m on to part 2
@buckaroobonsi555
3 жыл бұрын
Good Job!!!
@mackenziesibley7025
Жыл бұрын
What brand/ model 2m antenna? Larson?
@charlesbaker5309
3 жыл бұрын
BBI you want never have a problem with that set up, DAMN GOOD JOB man , get er Done 💪😁 CBJ NC
@maninthevan53
3 жыл бұрын
Nice job with a lot of patience 👍
@86jekstrom
3 жыл бұрын
Love the content.... Glad to see I have a couple tools that the pros use.
@brianragsdale4024
2 жыл бұрын
Will this setup work on top of a fiber glass camper shell?
@BoxBuilderIdaho
2 жыл бұрын
It needs the metal of the roof, so if you're able to put a metal sheet completely underneath the camper shell then yes
@beekeeper8474
2 жыл бұрын
Wish I had the balls to do this with my Tahoe love i get my antenna up higher. I just have it on the back hatch
@jhen291AL
2 жыл бұрын
i did it to my 16 tahoe it really works zero reflex, dk 5000w
@86jekstrom
3 жыл бұрын
Thanks for the tip on body glue....i never considered that
@BoxBuilderIdaho
3 жыл бұрын
Lap sealant is a very strong but very flexible rubber based glue unbelievably cool stuff
@86jekstrom
3 жыл бұрын
@@BoxBuilderIdaho how many volts does it take for miss to grow on the south side of the tree. I been hacked and wanna know 1 to 4 100% on to 45 fives doesn't belong .... Buck oh five at best gone
@craig_sez8534
3 жыл бұрын
Gotta watch this on tv..To bug eyed tryin to watch on my phone..Might get some tips on gettin my 102" on my cascadia to reach out some more..
@567caboverbob
3 жыл бұрын
Doesn't matter how much Loctite you use (most guys use too much), if you don't use primer it's a waste of time...........
@MajorMarvin
2 жыл бұрын
Thank you
@dimwittflathead639
3 жыл бұрын
Ok, one small thing eludes me about antennas, is the ground plane supposed to be magnetic or non magnetic?
@BoxBuilderIdaho
3 жыл бұрын
Either or.. the main thing is contacted the surface area of the vehicle body period at lower output power levels the the bond of the magnet to the body of the vehicle for more than substantially. But once you start to increase your power output level that magnetic connection becomes woefully inadequate
@CASH-1846
3 жыл бұрын
Kick ass video Luke!!!! Thanks
@madmannkc3562
3 жыл бұрын
Makes me want to build a mobile. Bad intentions in leavenworth ks. Good Friends with big train, rattle snake, gun fighter and zero 39
@KINGLOWNESS
3 жыл бұрын
THANK YOU SO VERY MUCH FOR DOCUMENTING THIS AMAZING START TO A BAD@ZZ INSTALL!!! KEEP 'EM COMING Mr. BBi!!!
@CT1JRZ
3 жыл бұрын
Very good setup.
@miltonflores3186
3 жыл бұрын
Over kill, few zip ties would have done the job, as TechNine says...some cats live in wonderland!
@melvinreaser3709
2 жыл бұрын
Nice vid
@PatrickCambria
3 жыл бұрын
Did you actually black out the low tire pressure light to avoid comments on it? If so my bad.
@BoxBuilderIdaho
3 жыл бұрын
I think if you read the previous comments you'll see I've already addressed this like three or four times. No I blacked it out to quit annoying me... I've since added the TPS sensors to my rims and I no longer have an issue..
@wbrown310
2 жыл бұрын
Crap! Now I have to redo my mobile setup.
@slingslingbinks
3 жыл бұрын
Nice job, Mr. BBI. Did i see a traction or low tire warning light on your dash? Have a good day, Waiting for the bonding video, Long live the Gunny Puck, Trapper 267 Colorado said that.
@BoxBuilderIdaho
3 жыл бұрын
Know what you saw was on on the dash is of tire pressure sensor indicator my fancy ass rims I have on that truck don't have the sensor embedded in the rim yet..
@slingslingbinks
3 жыл бұрын
@@BoxBuilderIdaho I copy that, Luke. Just busting ya about it. lol. Those sensor's are not cheep i'm sure. The average Joe can check his own air pressure. Carry on wayward son.
@RonaldTaylor-n3h
Жыл бұрын
How to make two hot antennas for my suburban?
@juanfgonzalez2039
3 жыл бұрын
Beautiful
@RC-Heli835
3 жыл бұрын
So Oh!! I'm anxious to see what all is going into the rest of thisthing....... 16 pill? Radio? Finetuned Stryker 955? This is exciting!
@BoxBuilderIdaho
3 жыл бұрын
nahh D-rail radio.
@RC-Heli835
3 жыл бұрын
@@BoxBuilderIdaho You know D-Rail? Unfortunately he's 2 hrs from me. I was gonna drive over there and wait on him to fix my Stryker 955. Turns out I had a bad mic and didn't need to go. But looking back actually maybe I never had a bad mic. The screw fell out of my antenna a couple weeks later not allowing me to use my 955 or backup Cobra 19. So it could have been a loose antenna acting up all along when I thought I'd lost modulation.
@RC-Heli835
3 жыл бұрын
1:16:16 Nice Antenna analyzer.
@mikeanderson3565
Жыл бұрын
Your only going to run one antenna why not the middle of roof. They say to make the perfect ground plane ground needs to be even on both sides. Huge power you can run a coat hanger tuned. But I go parked and run a 102 inch whip center of roof worked the best. I never got a match with two antennas for a true beam. I believe the feed antenna would have to be the back. I did not feel like putting use less holes in the roof. The 30k predator is a hell of a antenna 7 feet in the center of my highlander. You did a excellent job on the roof liner. I understand your more directional on the back signal will follow the longest ground path but two antenna would be way more direct with the long ground. Mr dbi take care my 54 foot beam never turned since my woman passed. Stay safe my good friend. I'm building a truck can't stay in one place to long. Your friend till the end troublemaker aka 713 Mr utica ny 73s
@mikeanderson3565
Жыл бұрын
I'm bad sorry BBi I said dbi stay safe I got your back lots of hatters out there. The true reason is your to smart for them and your audio is full studio sound. Been off for 6 years, at 46 is to early to pass, now I'm a rolling stone but I don't wear a hat but I found a lot of homes lol. One favor you here the pimp aka 369 tell him I'm still alive. 73s good friend.
@charlesbaker5309
3 жыл бұрын
How long is the coax from the puck? CBJ - North Carolina
@BoxBuilderIdaho
3 жыл бұрын
12.5 feet
@charlesbaker5309
3 жыл бұрын
@@BoxBuilderIdaho hey my friend where is the best place to get that coax and what exactly is it called? Thanks man 👍
@unclequack5445
2 жыл бұрын
BBI is the "Jhiddu Krishnamurti" of amplifiers and all things CB related .
Пікірлер: 151