Specs of this build: Motherboard - Gigabyte Aorus Z790 Elite AX kzitem.info/news/bejne/mY2BnYqjrqp3q6Q CPU - Intel Core i5-13600K RAM - Crucial Pro 32GB Kit (2x16GB) DDR5-5600 NVMe SSD - Corsair MP600 GS (kzitem.info/news/bejne/mXqKp52JbqKBg6g) PSU - Corsair RM850X PSU - kzitem.info/news/bejne/joOGuZ-ea5qglXY GPU - Nvidia RTX 3060 Ti kzitem.info/news/bejne/po540pV5pXSmdYo Fans - Lian Li SL-INF 120 fans (kzitem.info/news/bejne/uJV31p2EmImmmJw) and Reverse fans (kzitem.info/news/bejne/q66er4SHg56LZXo) AIO Cooler - Lian Li Galahad 2 Trinity SL-INF (kzitem.info/news/bejne/0IqQ2GpjfIKUdH4) Related videos: Lian Li SL Infinity Reverse Fans are fantastic kzitem.info/news/bejne/q66er4SHg56LZXo Lian Li Galahad Trinity Cooler and Reverse Infinity fans BTS kzitem.info/news/bejne/wmtsvHWof6Renag Lian Li Galahad 2 Trinity SL-INF all in one cooler review kzitem.info/news/bejne/0IqQ2GpjfIKUdH4 Lian Li Galahad AIO 240 unboxing install and benchmarks (in the Lian Li Air Mini) kzitem.info/news/bejne/uYulq6yFhGiBdw Case - Lian Li Air Mini kzitem.info/news/bejne/so-a36xjq3ODhm0
@thomaszinser4894
Жыл бұрын
Watched this video over and over until I finally understood all the connections. Thanks for taking the time to explore each of the connection options. It was a massive help.
@TheProvokedPrawn
Жыл бұрын
Glad it was helpful! Hope you enjoyed enough to subscribe 🦐
@Notpropianist
5 ай бұрын
@@TheProvokedPrawndis vid made me sub 🦐🦐
@ze2342
Жыл бұрын
Great video as always, really glad that you can connect the other infinity fans in the case to the Galahad controller to limit the amount of controllers needed in the back of the case
@stewie_
Жыл бұрын
I just ordered this cooler. My first AIO, can't wait to install it. The infinite mirror is the best.
@TheProvokedPrawn
Жыл бұрын
Good choice!
@bronsonwhite6487
4 ай бұрын
Great video, and thanks for all you do. After doing a lot of trial and error of installing this I noticed a few things. You don’t need to connect the pump to the fan controller. The pump has a internal controller that already works with L-connect via the USB 2.0 header. (If you run out of USB 2.0 headers get the NZXT sata powered 2.0 header expansion). The cable you connected from pump to fan hub is supposed to connect directly to motherboard to control RGB via mother board software if you choose too. It’s not entirely needed. The small adaptor cable you used to plug it into fan hub (360mm GA ll SL-inf comes with 3 of them, mine did) is to connect single pack(s) SL-INF fans to the fan controller that comes with pump.
@TheProvokedPrawn
4 ай бұрын
👍🏼
@anthonyrcortezable
5 ай бұрын
Hey mate I just wanted to say thank you! I followed Lian li instructions but they really don’t take into account AIO connections with other sl fans. Once I changed stuff around to your direction, viola! I will say for others that are still struggling, I had the splitter connected from the AIO pump to the fan chain and only had RGB on a few fans and no fan control in L connect. Once I removed that connection and just had the rgb cable from the pump to the fan hub and ran the other cable provided to the hub it all worked. FYI my setup is: Lian li Galahad infinity II (fans replaced with SL v2) and 5 other SL2 v2 fans. 6 fans chained to port 1 and 2 exhaust fans linked to port 2. Hope this helps someone 👍🏽
@anthonyrcortezable
5 ай бұрын
More to my comment, the fans again stopped working. Upon further inspection, the fan hub micro usb/usb header cable from the fan hub seems to be the issue why the fans either don’t show up on L connect or continuously drop out/lose rpm sensor etc etc. I have managed to place the hub in a position it’s happy for now but highly recommend people purchase a micro usb to usb header cable as I’ve read several people have this same issue. Cheers
@iamseclude2107
Жыл бұрын
Great video and very thorough. Just got mine installed yesterday and currently waiting for my usb header extension 😅 can’t wait to finally see this baby in action!
@TheProvokedPrawn
Жыл бұрын
Glad it helped!
@platinum_lego8384
Жыл бұрын
I am getting a 360 one soon for what will be literally my first pc build and am excited about it, your video did a great job explaining how to install it which was what i was mildly confused about how to connect the wires by reading the manual. (build will be in a Lancool 216). Now on to a tangent: why do the 3 pack infinity fans use a totally different connector than the single packs and the aio fans, in what way does that make any sense at all, it would have made sense if they updated all the cables for all their offerings but no if you wanted to use the Galahad infinity with the 3-pack fans your best best bet is to buy an extra set of fans to use instead of perfectly good fans included just to avoid the hassle of a second lian li fan hub, it just really does not make any sense to me, as for the singular fans i suppose it could have been worse if an adapter wasn't included at all but they should have just been compatible outright instead of having literally 3 types of connectors; 1 of which (3-pack) is completely incompatible with the other 2 however one of those 2 needs an adapter to talk to the other one (single needs adapt for AIO), just why? Anyhow sorry for the rant, good video and thanks for helping me understand what I will need to do. (in case anyone is wondering the AIO includes 3 adapter cables which now that I am thinking about it, is exactly enough to fill out the hub so i guess that makes more sense now but that does not excuse the different connector for the 3-pack fans though)
@ARXInfinite
10 ай бұрын
Tbh I was thinking the same thing and am thinking about getting the AIO. Just to confirm the AIO comes with adapters to work with the 3 pack Fan Hub with its different connectors?
@TheMdhennis
11 күн бұрын
I have the aio 360 and bought 6single infinity fans. Should i use my controller that came with aio or purchase a 3pack and use that controller?
@platinum_lego8384
11 күн бұрын
@@TheMdhennis assuming the connections are the same, it should work
@khanmu29
Жыл бұрын
Love your videos! Question. Here is my set up: Galahad II Trinity pump 2 uni fans on radiator 3 uni fans bottom 3 uni fans top 1 uni fan rear With this set up is it possible to connect everything to one l-connect controller? I don't need to run anything through the motherboard, only l-connect. I've also seen that the galahad II comes with its own controller which is different than the controller that comes with the uni fan 3 pack. Which one would be more preferable to use?
@IISenjuHashiramaII
5 ай бұрын
I sure hope you’ve got your answer by now but for those who are wondering the same thing - definitely use the one that comes with the three pack if your lacking enough headers for all your fans on the l-connect hub that comes with the AIO. Happy to explain why if needed.
@Omega-EP
Ай бұрын
@@IISenjuHashiramaII This was so helpful. So the AIO does provide you with a hub for its cables, BUT you CAN run the AIO through an older hub (i.e. the UNI FAN hub) after which it should be connected to the motherboard via an internal USB 2.0 header, is that correct, hokage sama?
@TheMdhennis
11 күн бұрын
@IISenjuHashiramaII so use the controller that comes with the aio?
@Omega-EP
11 күн бұрын
@@TheMdhennis Yeah, he never replied to me, so I'll just do my best to reply to you. As you do get a controller for the AIO, there's no point in not using it. Lian Li can't expect you to buy a different one for the infinity fans included, so it'll definitely WORK putting the fans in that one. That being said, I do think the AIO hub has a lot fewer ports for fans if you were to plug in more. Case fans or the like. You're probably meant to buy at least one three-pack as well and then hook all other case fans (provided they're the same model as the AIO ones) up to that one.
@TheMdhennis
11 күн бұрын
@@Omega-EP thank you so much for the reply!
@GhorabWS
3 ай бұрын
Thermal paste should be applied also to the CPU and the surface? or just the pump surface?
@noahschaub1984
3 күн бұрын
I connected the pump to the motherboard via usb and the fans to the infinity fan controller via usb from the 3 pack. Everything seems to be working perfectly fine without needing the pump control box. Would it be better to have each on its own separate controller or is it okay as is? My board only has two USB headers. Everything works in Lconnect including quick sync
@RolfenK
3 ай бұрын
sadly, what every tutorial seems to not cover properly is the distinction between the connection to motherboard sync and L-Connect sync with the controller
@Jordansd789
10 ай бұрын
What happens if you plugs the connections to the cooler with the arrows down? If you look closely at the plug and socket it seems like the arrows should be facing the other way
@andrewt123at
Жыл бұрын
Does this cooler have a coolant temperature sensor like the Corsair aio’s? I really like setting the fan curve for the aio fans based on coolant temp.
@FinnaBin
Жыл бұрын
Its not indicated on the outside of the unit i believe you have to go into your app and look at the temps
@davidpradelli9177
11 ай бұрын
Glad to see than this AIO fits in side position even with the front fans bracket. Im actually fucked by my Artic freezer II which is 66mm thick and btw doesnt fit. Will buy the Trinity II soon, thanks to you !
@connorromeros102
Жыл бұрын
13:54 you mention there are two ports on the pump head then describe one of them as a 5V ARGB port. What's the other port?
@youraveragebros
Жыл бұрын
Thanks for an informative video. I really needed this for a guide on my 1st PC build. LEGEN…wait for it…DARY
@TheProvokedPrawn
Жыл бұрын
Haha. Not heard that one in a while
@francoquesada372
11 ай бұрын
Thank you so much for walking us through this. The instructions it came with were barely intelligible 😅 But now it all works perfectly 😎
@TheProvokedPrawn
11 ай бұрын
Glad it helped! Hope you enjoyed enough to sub!
@jawnutssun2728
Ай бұрын
How did you connect the other infinity fans to the controller? Don't they have a different connector?
@tombaird5115
5 ай бұрын
Thank you for the video. Very helpful. One thing I'm confused about still. If I'm leaving out the controller (my case is too small) I can hook up directly. There are two wires from the fan radiator assembly. One wire is obviously a fan controller. But what is the other one? It looks beefier like it eats power. It has, for its size, two chunky wings, three holes, and three wire leads. It does not look like an LED, but the RGBs are not lighting up. Any guess where I can plug it? I'm using an ITX board so I will probably need to craft some workaround.
@ritesh146
2 ай бұрын
Hello, I just installed Lian li Trinity 240 which didn't come with the Adapter. When I powered on the PC for the first time, the fans lit up and rotates, but the CPU head didn't light up. Am I doing something wrong?
@4ZTR0
7 ай бұрын
question does it come out of box as intake fans?
@TheProvokedPrawn
7 ай бұрын
Exhaust
@doppelganger_
4 ай бұрын
You are the best. Extremely useful and riveting to watch. You helped me solve an issue I was having, thank you!
@TheProvokedPrawn
4 ай бұрын
Glad to help. Hope you enjoyed enough to subscribe 🦐
@Atomic_13
8 ай бұрын
i have bought lian li infinity fans and im planning on buying this cooler, but can i just plug the cooler in my existing hub i have with the included adapter cables from my fans? i ask it because i only have 2 usb ports and then can do everything with only one controller. But my fan controller from lian li has different plugs (much wider) and my question is can i plug this cooler in my usb hub i already use with the adapter cables that came with my fans.
@userbunny14
6 ай бұрын
oh the cooler comes with the controller? saves me having to purchase another set with a controller then. which is great, because I want to use the reverse fans for my 5 intake fans, and other then the cooler, I'd only have one other 'regular' fan, and I can only find the controller with sets of 3 regular fans.
@geogadget1
Ай бұрын
I have the Lian Li Galahad II Trinity 240mm the difference is my doesn’t have the SL at the end and it didn’t came with the black Controller box. I’m not sure if I did everything correct because my Ryzen 7700X runs around 84’ to 94’ Celsius. I’m new to pc building and gaming but I don’t think this is normal. I don’t know if it’s because of my wiring set up or not enough thermal paste despite me following the instructions as best as possible. Any help will be greatly appreciated. Also at 4:35 there is a tiny port located in the upper right hand corner of the pump. With my set up I have a wire connected to that port as per instructions but I noticed that there isn’t one in this set up. I am wondering what is it for if it’s not necessary.
@QueLoKevin
7 ай бұрын
I'm redoing my PC with this AIO and triple packs of Lian Li fans. It seems like the AIO comes with a different controller than the one the fans come with. Which one should I use and how, since they both have different connections?
@kennyurbina6172
Күн бұрын
can you connect 6 more sl inf fans to the same controller that comes with the galahad AIO?
@bradcon2009
7 ай бұрын
Purchased the GA11 Trinity 240 Question regarding PWR I have connected to the CPU 4 pin? The usb header, SATA Connection are installed. I am experiencing a DRAM problem with yellow diagnostic light and inability to install two channels of DDR 5. Connected to CPU 4 pin in the belief that the bios will not boot unless a connection is made for controlling temp of AMD 77000 CPU.
@EvanGkolfin
Жыл бұрын
I don't understand isn't the pump goin to be connected to the "cpu fan2" on mobo? How will the controller know which fans are the fans from the radiator? Unless it controls all of them together but that will be more noisy if you have more fans in your case. In my opinion, as I understand it the case fans should follow the gpu temp/curve and the cpu fans(radiator fans) should follow the cpu temp. Am i missing something?
@fwtanim7401
7 ай бұрын
Is the thermal paste pattern provided by lian li recommended? Like does it spread any good?
@RogueWraith909
Жыл бұрын
Smexy AiO is on my shopping list in 360mm config for my new rig.
@dariusnoelwilliams4084
9 ай бұрын
Im confused, how many hubs do you have in here? I cant see how all the additional fans are connected together with the AIO as you only showed the AIO being connected to its HUB would appreciate some help.
@Omega-EP
Ай бұрын
Does the cooler come with the hub itself or must I buy a 3-pack of Infinity fans to be able to connect it through L-Connect? Also - if I were to choose using standard Uni Fan SLV2s over Infinity fans, would the AIO still be operable through the older Uni Fan hub controller, or does it only run through the Infinity version of the hub? :) Many thanks in advance!
@TheProvokedPrawn
Ай бұрын
The cooler does come with a controller. I did show this I believe? But you can't mix fan versions with Lian Li controllers.
@mirahgirl01
9 ай бұрын
My AIO came with 2 controllers you were able to plug both of your white leads into one side by side mine there isn't a 4 pin on the one that has the micro USB and 2 SATA cables instead I got 2 controllers and the second one has 3 and 4 pins only on it I don't see the manual showing 2 just one how do I connect the 2 controllers together any help is valued!
@_merkoka6457
11 ай бұрын
Hi Prawn! I've just built my first pc, and something i ran into along the way I could really use your input on. My motherboard has only 2 USB connections. however I need 3 in total, 1 for my strimmer control box, 1 for my SL INF tipple pack control box, and 1 for my Galahad Trinity II 360 (USB required to control the RGB in L connect.) I've bought a NZXT USB hub but none of the devices I plug into the hub are being found by L Connect. Have you been able to successfully control Lian Li products in the L connect app while going through the NZXT hub? If so, this would really help me to narrow down that I have a faulty part somewhere, and be able to continue my troubleshooting. If you haven't had success with the NZXT hub, my next idea was to just take the L and plug one of the products in to sync with the motherboard. However when I plug any of the products in to the motherboard using an ARGB 3 pin header, they aren't being found in my motherboards software (MSI mystic light.) Also a video going over some of these various connections could possibly be an idea for the future. :D I know this is an older vid, so tyvm if you happen to respond to this. It's much appreciated
@kevinrohoman6857
9 ай бұрын
Did you ever figure this out?
@connorromeros102
Жыл бұрын
To see the infinity mirror with the included infinity fans on the AIO, is the AIO intaking or exhausting?
@virus_a
Жыл бұрын
Thank you for the helpful videos! And then with one of the most beautiful voices on KZitem...🥰
@davidpradelli9177
10 ай бұрын
Quick question just to be sure : im gonna install my galahad II AIO + full SL inf fans + double strimers V2 (CPU+GPU). My motherboard only has 2 ARGB ports so i gonna need to buy the Lian Li ARGB Cable accessories kit you mentionned in your description right ? Thx for your answer !
@simonhughes-king
Жыл бұрын
I found the Galahad 2 copper plate was very convex. It needed a lot of attention and sanding/lapping to get it flat. This is with a 12900KS, (IHS lapped) and a contact frame.
@Karlosact
5 ай бұрын
Where do you connect the other fans? In the hub that comes with the 3 pack of infinity fans? I'm going to put that AIO PUMP in my build and I want to add 7 x uni fan sl-inf, but I don't know where they would connect
@bronsonwhite6487
4 ай бұрын
Connect them all to the hub that came in the 3 pack. Discard fan hub that came with AIO. Newer/more reliable controller than the one that comes with pump(has 2 sata cables and different connectors). 3 pack controller should come with a few cables, use one of the few to swap with the daisy chained fans that come pre installed on the radiator. As long as the pump is connected to USB 2.0 header you can control it through L-connect. The other cable that attaches to pump (the one he used to plug into fan hub) isn’t needed. The pump has a internal controller that works with l-connect via usb 2.0 header. That cable is only if you want to control pump RGB with your motherboard software via 5v rgb port on motherboard.
@MrVoayer
Жыл бұрын
Two different motherboards were used in this demo: one with error code display and one without ! So, both the controller and the pump have to be connected to USB2 headers in order to be recognized by Lian Li's L-Connect 3 software? If I have tripple packs of old SL INF fans with their own controller - should I ditch it and connect old fans to the new controller of Galahad? If I buy four additional Reverse fans (for O11 Dynamic EVO case) how do I daisy chain them and mix them with old SL INF fans? How do I connect them to that new, Galahad's controller? Seems to me that some more vides are needed to demistitfy all the possibilities when using old and new SL INF fans with Galahad 2 Trinity SL INF AIO cooler ! This video is a great appetizer !
@oTheDucky89o
7 ай бұрын
Hi, if the AIO fans is connected both PWM and ARBB to the dual port from the pump.. How do you control the RGB from the L3 since it's a closed loop connection and no ARB connected to the unihub
@Sam-kd5cx
10 ай бұрын
I can’t seem to get the Pump Rgb to be controllable. I’ve plugged the cable with the arrow into the extender cable that goes into the Lian li hub. But the aio won’t show up in l connect
@saint4lunatics
6 ай бұрын
did you use 2 controllers for the fans or 1 and connect the aio to the motherboard directly, i sent you a message on discord but didnt get nor expect a response
@tahmidulhaque1156
11 ай бұрын
My galahad 2 trinity is not showing in l connect software. Just white light is showing and I can’t control rgb. I’m using lian li uni fan sl v2 hub. Please Help
@chieffalley4955
4 ай бұрын
i got the Lian-Li Galahad II 360 Trinity SL-Inf, i plugged all the cables in but my pump doesnt pop up in the L connect so i cannot change that colour only the fan ones, anyone know how to fix this?
@AjaySharma-bm5mb
Жыл бұрын
How do you have that many uni fans connected to 1 controller? Aren't there more than 4 groups?
@TheProvokedPrawn
Жыл бұрын
one group is connected to the sync port of the standard controller, the rest are to the main ports.
@AjaySharma-bm5mb
Жыл бұрын
@TheProvokedPrawn ah okay so you simply use the controller that comes with the 3 pack, not the one that comes with the cooler.
@joelwilsson4966
9 ай бұрын
If i already have a pc full of sl inf fans connected to the sl inf hub with the bigger flat connector do i have to use the hub that comes with the aio? Or can i keep my hub and just connect the aio pump to a sys fan/water pump connection aswell as sata power and the usb header to the aio pump. If not is it atleast possible to connect the rgb connection from the pump to my current hub?
@andrewmarshall3275
7 ай бұрын
Hi Provoked Prawn- Loved the video you mentioned a solution if out of usb mobo headers ? I’m building with a z790itx board and so can either plug the usb from the pump in, or from the connecter box with its additional cable. The radiator fans are plugged into the mobo cpu fan header so that the motherboard doesn’t error. And the pump is plugged directly to aio header. If the pumps usb cable is plugged into the mobo I get rgb to it only and the fans run without rgb. If I plug in the adapter cable from the little outlet box to the mobo all the case fans have rgb but the actual aio cooler does not. I tried a USB splitter that came with the motherboard but it did not work. Likewise the little 6 pin on the aio to the connector box via 3 pin adapter made no difference. My motherboard the Asus z790 itx only has a 4pin rgb not 3 and so I’m trying to do all via the lian li connector box. However the 1 mobo usb is meaning I can only use rgb on the fans or the aio cooler head. As someone who’s clearly very familiar with this setup- do you have any suggestions ? You mentioned in the video you had a solution for if not enough usb ports but I cannot see it below ? Thanks :)
@TheProvokedPrawn
7 ай бұрын
kzitem.info/news/bejne/xW6sq4CYkImSdoY
@andrewmarshall3275
7 ай бұрын
Legend! Thankyou. Will I still need the little 6 pin plug that plugs directly into aio pump then into the control box ? I can’t really see its use as it seems to work without it ? :/ And when usb plugged in I get rgb as well.. I thought maybe its function was to route rgb to the control box to the motherboard via single usb but it didn’t work out that way… Any explanation of what this little cable does , which terminates in a 3 pin rgb, then connector allows it to connect to control box Thanks again :) Your answer was greatly appreciated
@stjah69
11 ай бұрын
Hello, I have a Corsair configuration. AIO 360 LCD, 6 fans 120 QL, ram32go bars and my Corsair keyboard. I would like to buy this AIO Lian li. But is it possible that it does not work because I have ICUE and commander core Corsair? thank you
@MazApocolypz
20 күн бұрын
does anyone know if this cooler will work on the msi b450 a pro max motherboard? I dont have any ARGB connectors on my mobo but want to pair this cooler with a 5800X3D.
@Kortex4F
6 ай бұрын
Can't find the info in the description regarding running out of usb connections on the mobo. I assume it's a hub but some are reporting issues in the comments.
@bronsonwhite6487
4 ай бұрын
Get NZXT usb 2.0 header hub. Requires sata power from PSU. No issues so far
@bopT.
9 ай бұрын
with the hub included can i fit another 7 single lian li fans along with the 3 included with the AIO all in that one hub? I heard that the 3 pack connectors don't work with the hub included with the AIO
@extv1p3r65
9 ай бұрын
So what does the little cable that connects the pump to the controller do? Can I use that instead of the USB 2.0 cable from the pump?
@jommammaxse95
8 ай бұрын
I think that cable is optional but I’m not sure this guy doesn’t do a great job explaining
@maxfry3343
7 ай бұрын
hello! the biggest drawback is the inability to connect USB 2.0 to the front panel, because there are only two connectors. any idea?
@TheProvokedPrawn
7 ай бұрын
kzitem.info/news/bejne/xW6sq4CYkImSdoY
@maxfry3343
7 ай бұрын
ty bro@@TheProvokedPrawn
@BenchmarkUser
Жыл бұрын
is just mine or the pump is not MB SYNC argb?? whene i try on l-conect 3 i cnt do the MB SYNC on the rgb on the pump, and BTW this pump at 3200rpm is too dam loud
@outlawsheeq
10 ай бұрын
why pump header is connected to the cpu_fan and not the sys_fan4_pump?
@RathalosEmperor
Жыл бұрын
Do you have to have the lian li logo on the infinity mirror? Does this also mean I have to use this controller over my infinity fans hub I got with the 3 pack?
@connorromeros102
Жыл бұрын
kzitem.info/news/bejne/w56GsJaCh51ip6w sounds like yes the infinity mirror has the logo while the other two options do not.
@ATTACKM4N
Жыл бұрын
How did you end up connecting the rest of your fans? Were you able to connect them all to the controller that came with the AIO? Or do you need to use an additional controller that comes with the 3 pack?
@TheProvokedPrawn
Жыл бұрын
I used just the original triple pack controller on its own to connect the entire system. But you could use the converter cables included in the box and connect them to the ports on the included one.
@teamoney80mg
Жыл бұрын
@@TheProvokedPrawn I really like this system and purchased it because of your videos. Could you do a video about how you connect the AIO to the three pack fan controller ? Do i not need to use the controller that came with the AIO if I have the controller from the three pack?
@tropicalfish666
Жыл бұрын
Thanks for the video. Very helpful. Did you use two of the fan controllers?
@jvs6578
11 ай бұрын
Would you help me? I don't have enough usb outputs on my motherboard so I couldn't connect the pump's usb, so I can't even turn on its RGB, is there anything I can do to solve it?
@TheProvokedPrawn
11 ай бұрын
kzitem.info/news/bejne/xW6sq4CYkImSdoY
@matthewlloyd8131
11 ай бұрын
would i need to remove the motherboard from my case for am4 socket?
@khulalanup
11 ай бұрын
what is the name of the case you are using in this build.....thank you
@TheProvokedPrawn
11 ай бұрын
Lian Li Air Mini kzitem.info/news/bejne/so-a36xjq3ODhm0
@krystiangaszynski2692
6 ай бұрын
@TheProvokedPrawn So I’m planning a build with 10 sl inf fans (3 bottom, 3 up Aio, 1 at the back and 3 on the side. I bought 3 reverse fans for the bottom (one pack), 1 single normal fan, and also the Galahad 360 Aio, which comes with a controller. If I want to control the rgb on the Aio via L-connect, I have to to plug it into the controller. Which leaves me with only 3 slots left, when I need 4 just for those 10 fans. Is it possible to hook that one single back fan to whichever group of 3 fans, if so which Lian Li cable do I need for it.
@bronsonwhite6487
4 ай бұрын
Don’t need to plug pump into the included controller. Look at my latest comment
@Tamjidislammayel
11 ай бұрын
What is case name please
@appak6280
Жыл бұрын
Can i connect the Galahad 2 Trinity to the controller that comes with the SL120 v2 fans?
@anil24007
Жыл бұрын
Nice information you share sir. Thank you. Which chassis have you used and Is this configuration really need extra fans which you have used.
@coys4life450
6 ай бұрын
O11 air mini comes with 3 pre installed non argb fans
@barjee8965
2 ай бұрын
I commented on your other video and after watching this one im more confused lol, on their website and on the suppliers site where i just bought mine it says the pump can act as hub for rgb devices, on their site it says you can plug an ARGB device into the pump in order to control it via the L3 software, but in the video you went from the pump into the controller, im so confused >.< plz send help XD EDIT: in the case that you can use the pump as a hub for rgb via lconnect then you can just plug the daisy chained fans into a pump header and the rgb into the pump head without the need for the black hub, the pump uses the usb to motherboard connection to enable L3 software
@Danny22-11
Жыл бұрын
How can i update the Galahard 2 Firmware? It shows only server error 🤔
@irolledthatlucky7075
7 ай бұрын
My cooler did not come with the remote that yours did :( is there a way to do this without that part?
@erasmoestrada4260
7 ай бұрын
I am stuck at this same part lol I don't have that black controller part. Taking a break because I am frustrated at the moment.
@EliteNemisis08
6 ай бұрын
Same here mine didn’t come with it. About to return it and go with a MSI cooler
@erasmoestrada4260
6 ай бұрын
@@EliteNemisis08 I ended up just plugging in whatever plugged in and it worked well. Wish there was a better guide for the model I had.
@irolledthatlucky7075
6 ай бұрын
@@EliteNemisis08 @erasmoestrada4260 I remember looking and finding that you can purchase the hub part separately on the internet. It was like $20 tho. Annoying. What I ended up doing was just using the hubs that came with the lian li fans I got extra of. They don’t have all the ports like the one in this video but they have half of them. So I wired as many of my fans that could fit into it and the rest directly to my motherboard. That left two fans that were not gonna be connected to anything for the RGB, but it worked out because I faced those ones out the back so that it doesn’t matter if they’re lighting up or not!! Don’t give up 🩵
@marcocaboose9683
10 ай бұрын
Yeah nice video and all but my box didn't come with a RGB control box nor do the instructions specify what to do with the connections without one. I'm new to the PC build world but my lord is there no videos that assume you don't have one.
@CoconutGaming1337
Жыл бұрын
I also want to get the 360mm version but my motherboard (MSI b450 a pro max) doesn't have any 5V 3Pin RGB header. Is there anything I can do as a workaround?
@kieranbrekke1676
7 ай бұрын
Did you get a solution for this? Im in the same position
@mc4tarzans
Жыл бұрын
If you buy a multiple additional single packs, infinity fans do you know if you can connect them to the control box that comes with the AIO?
@TheProvokedPrawn
Жыл бұрын
kzitem.info/news/bejne/12uhqoqQppeBjIY you need the accessories RGB kit basically
@mc4tarzans
Жыл бұрын
@@TheProvokedPrawn I'm sorta confused so I'll just explain my entire situation and hopefully, maybe you can explain a bit better. I am planning to buy the Lian li Galahad 2 trinity Infinity, meaning that I will get the AIO controller. I also want to get the reverse fans for intake, and since the AIO already comes with 3 exhaust fans, I will need 6 intake fans (inifnity) and 1 exhaust (also infinity), meaning I will need to buy the rest with single packs, hence I won't get a Lian li infinity controller. What do you think is the best way to handle this situation? Im thinking maybe I can connect the other 3 sets of fans and connect it to the controller that comes with the AIO? please help
@AnonAsd
Жыл бұрын
@@mc4tarzans just commenting here that im also interested to know because im planning the exact same thing. The 6 intakes would be reverse blades so I would not get a 3 pack controller
@lukasjung3096
Жыл бұрын
@@mc4tarzans as im planning the exact same thing, im also interested in a solution for this topic. I learnt from my recent research that you can plug the single infinity fans into the controller that comes with the AIO. So it should be possible (in my logic) to daisy chain the single reverse fans and connect them to the controller without having to buy the triple pack for the other controller.
@PedroHenrique-nd7kt
7 ай бұрын
@@mc4tarzans Is it possible to use the controller that comer with the AIO like u said?
@zenjim1305
Жыл бұрын
Can you change the lcd displace to any photo or short video like live wallpaper?
@TheProvokedPrawn
Жыл бұрын
no
@fuzzba11able
6 ай бұрын
You have a list of the whole build but no case name! plz can I have the case name??
@fuzzba11able
6 ай бұрын
Is it the Lian Li O11 Air Mini??
@TheProvokedPrawn
6 ай бұрын
@@fuzzba11able yes
@raynathanielcaparas8064
6 ай бұрын
No ones showing an amd demo for this specific aio
@DarkStarGaming065
Ай бұрын
I don’t have that control module part in mine
@pure-gaming
8 ай бұрын
really appreciate your video explanation just subscribed and liked
@TheProvokedPrawn
8 ай бұрын
Thank you.
@Omega-EP
Ай бұрын
You didn't subscribe until now?
@Che7u
Жыл бұрын
When does this release?
@La_Tagliattelle
Жыл бұрын
why i don't see my pump in L-connect?
@2M4NU
Жыл бұрын
Love your videos! Very informative !
@TheProvokedPrawn
Жыл бұрын
Glad you like them! Hope you enjoyed enough to subscribe
@2M4NU
Жыл бұрын
@@TheProvokedPrawnAlready am since a few weeks that i found your channel. I try to like and share your videos as mush as i can. Hope your channel grows :)
@TheProvokedPrawn
Жыл бұрын
@@2M4NU thank you. That's really appreciated!
@johndoodoo5724
10 ай бұрын
Have the aio a refill port the first GALAHAD have it. Thx from germany👍
@garretvadr
4 ай бұрын
Can the screen display temps?
@TheProvokedPrawn
4 ай бұрын
No
@Boolap1337
9 ай бұрын
does the AIO come with paste?
@TheProvokedPrawn
9 ай бұрын
Yes. I showed it.
@Boolap1337
9 ай бұрын
@@TheProvokedPrawn ok, good. I thought that was ur own bought paste
@casey583
5 ай бұрын
Im failing so hard right now. 9 infinity fans to a controller. Ga ii cooler. Pump and 2 fans on the radiator work. Nothing else works, 7 other lights, 2 triples and a single, nothing. Just spent a entire night frustrated. Hate this build right now.
@bronsonwhite6487
4 ай бұрын
Using the controller that came with pump or controller that came with 3 pack?
@casey583
4 ай бұрын
@bronsonwhite6487 I'm all hooked up now. 9 SL INFs with the controller and wiring from the 3 packs. I did not have a INF pump so I put inf fans on my pump.
@sammandujano1452
Жыл бұрын
Could you not do a voice over for the entire video that way we can tell what part you’re actually talking about when you’re talking about it?
@TheProvokedPrawn
Жыл бұрын
I don't understand what you're saying. I did voice over the whole thing?
@dschNgz
8 ай бұрын
It is really a shame that you cant buy the sl inf controller stand alone and it only comes in 3pack regular fanblade design. When you dont need 3 regular fans like me and need reverse blade design fans, u are screwed... thanks lian li that you dont give a sht
@blackginkgo8169
9 ай бұрын
1 Year and that cooler is dead, all because the pump runs dry ...
Пікірлер: 153