Thank you! Just the information I was looking for. You made my day.
@engthink
6 ай бұрын
Nice!
@jbhawkster
6 ай бұрын
Very well done. Thank you for this.
@engthink
6 ай бұрын
Thanks!!!
@johngarcia8266
2 күн бұрын
Good Video Thanks
@engthink
2 күн бұрын
Thank you!
@anpatron4439
5 ай бұрын
Very nice video! Very useful info about the mixing up of the wires in the connector. Do you have a vid about the way each wire is held inside the connector and how it can be released so the wires can be rearranged inside the connector?
@engthink
4 ай бұрын
Thanks, good sugestion I will try to make soon.
@vsab786
Ай бұрын
Thanks for the nice explanation
@engthink
Ай бұрын
Thank you!
@misoo83
3 ай бұрын
Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂
@normanwray1341
5 ай бұрын
Hello dear friend thank to give me your good advice off that throttle, very interesting 😅😊
@engthink
5 ай бұрын
Thanks bro!
@Lobo-mv2ml
3 ай бұрын
I have a Phantomgogo R1 36v scooter. The make and model are Sine wave brushless controller 2HM-0. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
@XiaolinDraconis
Күн бұрын
He tested it by putting 5v through it... if you did what he did then you put 18v worth of batteries to it.
@LuanaSantos-ol7vy
Жыл бұрын
Valeu!
@engthink
Жыл бұрын
Bons estudos!
@vijayakrishnannair
6 ай бұрын
Nice 👍
@engthink
6 ай бұрын
Thanks.
@pasqualemacheda
7 ай бұрын
nel mio acceleratore ci sono 3 fili ,BIANCO ROSSO E NERO .LA MIA BICI E UNA 250 (MARCA VIVA) SENZA LA PREDISPOSIZIONE X L'acceleratore COME LO DEVO COLLEGARE ALLA CENTRALINA .CIAO E GRAZIE SONO CONDOR 69
@engthink
7 ай бұрын
Dai colori dei fili dell'acceleratore dovrebbe essere il seguente: rosso positivo. nero negativo segno bianco Cerca il manuale del controller per sapere dove collegare ciascun cavo. Buona fortuna.
@marvindeximo3709
7 ай бұрын
Thank you!
@engthink
7 ай бұрын
Welcome!
@NormanWray-hi8cu
3 ай бұрын
How could you use a baizifu conversion kit brushless kit moto sensor that as wire's red black and yellow 😊😅
@engthink
2 ай бұрын
Red = positive, Black = negative, Yellow = throttle proporcianal signal
@plig88luthierandelectronic63
8 ай бұрын
If I give on the signal , more than 5 volts dc , the motor goes Above the max speed ? .. I have an urbanglide escooter and I search how to unlock the max speed ,, my scooter have 25 km/h top speed , but I don’t know where I unlocked ,, it’s from dashboard or from controller ?
@engthink
8 ай бұрын
Its depends how they block the max speed. I am not sure tha the limitation is in the 5Vdc signal from the accelerator.
@plig88luthierandelectronic63
8 ай бұрын
Ok for this ,, I have one problem now ,,, I put on rear wheel a onother motor from other escooter , so the front wheel work from the controller 1 and dashboard 1 , and the rear wheel work from second controller and the second dashboard , I take only the signal throttle from first dashboard and I put it on the second dashboard throttle ,, it works perfect , but yesterday, when I give throttle the rear wheel spins backwards as fast it can !!! For some reason , I don’t know , I’ll check all connections and the cables and the phases , all!! I’m thinking to turn the wheel upside down , but the speedometer do not work , because the motor going to the wrong way ,, do you know what happen ? 😢
Пікірлер: 32