The old hot wrench never fails to deliver satisfaction
@thomasjones613
2 жыл бұрын
As a retired welder with 44 years experience, I would have welded that top plate that you replaced in the overhead position to get better penetration. Welding vertical down hill is really only for sheet metal. This is not meant as critisism, just advice.
@icesoft1
4 жыл бұрын
I believe LCT (Liquid Combustion Technology) is the new owner of Tecumseh engines - Since 2010'ish, based out of South Carolina (with other facilities in China and Australia)... Oh, and I also have the same log splitter, I'm impressed that the farmers managed to inflict so much abuse on it, leads me to believe that mine should last forever...
@WatchWesWork
4 жыл бұрын
It should!
@yako0000
4 жыл бұрын
"it looks like a Bangladeshi ship breaking yard" lol. i'll have to remember that one.
@86FxBdyCpe
3 жыл бұрын
Those are some scary looking places. It amazes me that type of work is performed all while wearing sandals and carrying those heavy pieces by hand. Those poor bastards...all for pennies an hour.
@froggleggers1805
3 жыл бұрын
@@86FxBdyCpe Poor bastards is right, I have watched more than a few videos on what they do and how they have to live, God bless those people. They find a way to feed their families and take care of those they can.
@rottiejakeluke
3 жыл бұрын
Great job. I’d suggest you fabricate a catch table on the side opposite where you stand working the controls. This will eliminate you bending and reaching for dropped wood. If you want another suggestion: bring it back towards the motor to protect the motor from dropped wood. Be careful not to block access to gas or anything else you have to get to .
@lewiemcneely9143
3 жыл бұрын
I don't think anybody needs to aggravate you OR Brian on your welding skills. FINE job! And I was hunting a 2nd hand splitter to fix up but nobody wanted to sell one bad enough so I up and ordered a new one. I think it's the only thing I ever got new. All the rest are worn down but not worn out and farmers aren't the only one for those 'tricks' OR there are a lot more farmers than I reqalized. GOOD splitter! Good as a million if it works. Thanks, Pal and GBWYall!.
@jazzerbyte
2 ай бұрын
Great log splitter save with the weld work to match!
@assessor1276
3 жыл бұрын
Nice job Wes - you are good with that welder! A buddy of mine built a log splitter and I recall that he used a stick welder running a Stellite hardening rod on the cutting edge of the wedge and that really helped it to deal with hard maple without so much wear.
@feildcar4578
2 жыл бұрын
Sometimes it helps to pre heat the steel where your going to weld it with a torch then weld it up when your working with a welder that's not exactly rated for what your welding.. I've done it many times and it helps.
@ickipoo
6 жыл бұрын
It lives again! Nice, satisfying repair. Thanks for sharing your work with us.
@WatchWesWork
6 жыл бұрын
Thanks for watching. It's nice to fix something with materials I had on hand.
@generaldisarray
4 жыл бұрын
I love me some god old gas axe work!! Great work Wes I use to do some summer work repairing regulators, welding gear, etc. for my uncle. He installed a 5/5 oxy/O2 tank system in a metal shop that cut seriously thick steel plate, think it was 7" or 8". It was a monster of a system, that crated a great fireworks display once it got cutting...
@JohnSmith-tv5ep
3 жыл бұрын
Dude, I really like your style and your attitude! 'Makin it work' !! Rebuilding things better than original so it won't break!! Just wish I could weld like you. AWESOME JOB!
@deenunya7735
3 жыл бұрын
That what a like about Your Work Ethic , getting the Right Materials to do the Job regardless of Cost , The Bolts, and using the correct type if Safety Pin than a Nail Good Job 👍
@riccroft710
2 жыл бұрын
"Bangladesh ship breaking yard", that's funny right there! I'd say you reinforced the top of that plenty strong enough. Good work, Wes.
@staind288
4 жыл бұрын
I realize this is an older video, but yet another fantastic how to/tutorial from ya, bud!
@garrydonnelly6433
3 жыл бұрын
G'day Wes. Love your vids and the new shop is a beauty. I saw some fellow with a log splitter who had welded a horizontal wedge as well so the machine splits a log is 4 in the one pass. Cheers mate.
@dwitcraft
3 жыл бұрын
Great camera work with the gas axe! I could almost feel the heat!
@oldman9642
20 күн бұрын
You probably won’t see this, I’ll try to get it on a more current clip but, dude, you lay the best looking weld I think I’ve ever seen.
@arejay4965
2 жыл бұрын
Made in USA Stuff! Truth Spoken: "Too Lazy to find it, Too Cheap to buy it". Wes, I salute you! Thank you for telling it like it is. What a great video on recycling machinery, I think most would have scrapped it, not you! Nice Rebuild, much better than original!
@adnacraigo6590
Жыл бұрын
Good idea cutting the web and adding that plate.
@dmoore8705
2 жыл бұрын
On the farm, what you call a nail is what we call a single use agricultural pin.
@ihrescue
3 жыл бұрын
Nice work - good project - very interesting video.
@jondavidmcnabb
4 жыл бұрын
Wes that was a great mid project redesign. You saved yourself a ton of time. Ever considered adding a 4 way splitting head modification?
@tdotw77
9 ай бұрын
👍Yeah, I was thinking that too. Coulda added another wedge on 'horizontal' axis, 90° from existing big wedge, and moved back a few inches so its a secondary process to the 1st big one. 👍👌🤔🛠️🔧🔩🗜️📐✏️📏🥽🔨⛓️🚜⚙️🍻
@crazyfvck
4 жыл бұрын
Awesome job dude! :) That thing was a wreck.
@sshaw7912
3 жыл бұрын
I used a 1/2" x 6" piece of flat bar on top of a piece of 1/4" x 4" square tubing. The square tubing is my hydraulic reservoir. I bought valve , pump & 4" tie rod cylinder from Northern Tool, and a 8hp gas engine. 30 years later it still works, but it is in need of a pump and valve.
@Frankiedoodle1941
3 жыл бұрын
I cant believe you lifted all those heavy logs yourself , should of gotten the wife to do the easy jobs lol, great show as always, give my love to the family, be safe and look out for each other, From the Uk
@bohhica1
4 жыл бұрын
Maybe add a four way to help in the older wood, nice work.👍👍👍🇺🇸🇺🇸
@mdouglaswray
4 жыл бұрын
Nice welds!!
@fredhart7904
3 жыл бұрын
Looks good great job repair, it you plan on using it for years you might think about changing the hydraulic oil, I have had one similar since 1982, old splitter still works fine, problem, it just keeps going and does not get tired, wears me out,
@JoeHynes284
4 жыл бұрын
congrats on 50k!
@simonyovino2126
4 жыл бұрын
Those are some beautiful welds
@gregdawson1909
3 жыл бұрын
quick tack weld on each of those bolt heads, then angle grind off, and you can buy yourself a few more "amps" with a healthy preheat on that thick piece, but looks like you have a perfectly viable repair there.
@AntonioClaudioMichael
Жыл бұрын
Good video came out great on the repairs @Watch Wes Work
@bombardier3qtrlbpsi
4 жыл бұрын
Nice job on the repair
@tommymann69
2 жыл бұрын
I love old log spitters. Some I have come across looks worst than this one. By the time I get thru fixing one . Its looks brand new plus has a lift on it to handle heavy logs.
@jimliechty2983
6 жыл бұрын
Good vid Wes! AIthough my original and normal focus these days, are machining related, I like your various content. It reminds me of the way I always approached problems, by fixing everything myself. I'm now getting to the age where that is much harder, but it's harder yet, to have someone else do it!
@WatchWesWork
6 жыл бұрын
There is a lot of satisfaction in fixing something yourself. Though, it doesn't always make sense.
@jimliechty2983
6 жыл бұрын
Yea, but doing what makes the most sense gets boring, and not nearly as much fun!
@tectalabyss
4 жыл бұрын
Hello Wes. Catching up on some of your older videos. Vertical down,is a big No no using a stick weld. Has the flux will run into the weld. Has far as I know Mig's do not do that . I have welded for over thirty years. Great job on the rebuild. Seems the people who owned it didn't use grease Lol. Liked,Shared.All my best.
@dansaver8247
2 жыл бұрын
Terrific job.
@turbocobra
6 жыл бұрын
very nice, that 3/4" top plate will outlast the rest of it for sure.
@WatchWesWork
6 жыл бұрын
It will boost the scrap value when it finally splits its last.
@thdevilmancometh
Жыл бұрын
KZitem is weird. Recommended a vid from 5 years ago., But I love your work. Wish I could stopped into visit when I was passing through, but you never answered my Facebook message. Anyway great video and work....thanks! Julian D
@phillipdean9879
3 жыл бұрын
Best tool ever the BFH!
@jimalexander1896
3 жыл бұрын
Nice on the welding!
@Martin.Wilson
Жыл бұрын
The best plan would have been to grind the tops of of all the bolts and replace them. What kind of mook would have used flat head bolts for this application....certainly never someone who had to take it apart for servicing.
@richwielechowski5191
2 жыл бұрын
Wes, you and I have one thing in common, love for our pets. Doesn’t matter what I doing, always have time to toss ball or frizz be for dog or stop and pet the cat.
@imysteryman
6 жыл бұрын
I have a splitter similar to this one and I built a shelf that is use when it is in the horizontal position. The shelf is attached to the bottom of the beam with 2 short pieces of 2x2 angle iron with 2 bolts. I welded short pieces of 2x2 to raise it up to the top of the beam leaving clearance for the wedge to pass by. Then I made the shelf out of angle iron covered with expanded metal. When I need to use it in the vertical position I just remove the 2 bolts and take the shelf off. It is much easier to use because when I split a larger piece I can just set half of it on the shelf and I don't have to bend over to pick it up again. If i were you I would remove those rails, I stand with my left hip touching the wood and control the splitter with my right hand. I try to never put my hands on the ends of piece of wood, I like my fingers way to much.
@WatchWesWork
6 жыл бұрын
That's how the rack and pinion/flywheel splitter is built. It has a big shelf all around the wedge and the ram actually pushes the wood through the wedge. Plenty of space to set the wood aside while working a big piece.
@tutekohe1361
3 жыл бұрын
A good trick is to have the wedge razor sharp. Mine is so sharp, I can put the wood in sideways and it will cut straight through it. It means you can split knotty wood super easy.
@joeyf504327
Жыл бұрын
is that cast 90* fitting on pressure side of the hydros safe? Looks like a water fitting and with the casting line right down the middle and it sketches me out thinking of 2,000psi within that fitting.
@bohhica1
2 жыл бұрын
The BFH is an awesome tool !
@slugster51
3 жыл бұрын
Have the same splitter motor was junk when I got it put a 6.5 predator for it works great use it heavily
@Brock_Corb
3 жыл бұрын
Why dont you hold screwdriver down similar to how you had vicegrips longways so you have 10x leverage to hold it from spinning. Cant do that on regular sized flat heads but on those 1/2 - 1" headed bolts it works great. Awesome content as usual keep up the work Wes!
@SteveSummers
6 жыл бұрын
I need a splitter myself. I was thinking why does he not just replace the top section?? And then you did. Good work and video Wes Thanks.
@WatchWesWork
6 жыл бұрын
Thanks. The replacement I-beam seemed like a great idea until I actually thought about it.
@iamrichrocker
4 жыл бұрын
say hello to Donna for us..
@RobertKohut
3 жыл бұрын
Nice!! Great job... :-)
@Chr.U.Cas2216
2 жыл бұрын
Dear Mr. Wes 👍👌👏 Very well done again and as always. If you still have this log splitter, kindly allow me to suggest that you change the small knob on the lever/handle to a billiard ball. Those can be grabbed perfectly well = suits great into human hands. Thanks a lot for making teaching explaining recording editing uploading and sharing. Best regards luck and health to all of you. Post Scriptum: Nice to see the great rodent detector Max.
@fricknjeep
2 жыл бұрын
just looking at other channels . good show thanks john
@BBICubicle
2 жыл бұрын
Yeah loved the shipyard comment. Another awesome video. Thanks!
@40yeartrucker25
4 жыл бұрын
I bought the exact same spleeter on sale at Menards for $699 in a create. About 5 years ago.
@stevenbenavente1229
2 жыл бұрын
Good job
@richo2895
4 жыл бұрын
That's a Win!!! Score
@charlesoliver4437
3 жыл бұрын
Thank you. Have me a few ideas for my log splitter
@OFCbigduke613
4 жыл бұрын
Cool video
@shaneharrison4775
3 жыл бұрын
That's the way you do it no nut or bolt can resist ye ole hot wrench
@MS-fs5xu
5 ай бұрын
Nice job! Needs painting 😅
@AUTiger1964
3 жыл бұрын
Nice rebuild WRs! Send it to the body shop for paint job and license the wife as an operator! Like you I prefer a vertical splitter to horizontal models!😊
@shaneharrison4775
3 жыл бұрын
Well done wes
@kenmccormick3052
3 жыл бұрын
any kind of knob at the end of the rod is fine.
@darellsunderlin4670
Жыл бұрын
You got a steel !!!
@curtkopp19
3 жыл бұрын
On this episode of “watch Wes wreck his wrist” screwdriver vs. impact.🤦♂️🤣
@bcbloc02
6 жыл бұрын
Maybe try welding a pyramid type shape on the base and you might be able to get it to split 4 ways in one press.
@WatchWesWork
6 жыл бұрын
They make cross shaped wedges that can split 4 ways. It's tricky though because you have to get the wood centered on the cross. This is still a major improvement over my splitting maul.
@6-4fab53
4 жыл бұрын
I know this video is a couple years old but... Check out Jody over at welding tips and tricks. He does a great job of explaining why you should go uphill on thick steel with mig vs down hill. Keep the great videos coming, love them all!
@Mad.Man.Marine
3 жыл бұрын
He also states in a video That if you know what to do there isn’t any problem welding. Downhill. All about puddle control.
@6-4fab53
3 жыл бұрын
@@Mad.Man.Marine I totally agree. But in my opinion there is a proper tool for every job if you know what I mean. Maybe I should have mentioned dual shield flux core as the correct tool but, I was just trying to educate. No disrespect or "know it all" coming from me.
@johnstrange6799
6 жыл бұрын
Decent for scrap price, material and some repair time. Split until something gives, then fix'er again.
@WatchWesWork
6 жыл бұрын
Or let it go. You can buy a new one of these for $750, and they have made them much better.
@johnstrange6799
6 жыл бұрын
$750 is an interesting number. I think (but it might be cutting it close, idk) that you could make a better one than you can buy for $750, but time time time.
@shaneharrison4775
3 жыл бұрын
That will.work better than the old one
@ranchdog7920
4 жыл бұрын
BFH Tech can solve a lot of problems .
@larryfischer1970
3 жыл бұрын
I saw a splitter that had a table out each side of the beam so you could stack incoming and did not have to pick up split logs off the ground.
@shaneharrison4775
3 жыл бұрын
I bet wes great job on the slide frame the wedge has its issues dads had a yolk threaded onto it
@danbartolini27
4 жыл бұрын
You gonna grease that slide?
@luisbatista1103
7 ай бұрын
He was soo young (Wes) you can hear in his voice .....nowadays he's Mr. YT....👍🏼👍🏼👍🏼
@kingsleycollins6730
Жыл бұрын
Nice work bro. Pls what is responsible for piston fast stroke, is it motor or control arm
@katelights
9 ай бұрын
the good old blue tip wrench. cant be stuck if its liquid!
@richardluce7875
4 жыл бұрын
Just found your vids. Luv em. Down to earth let’s get it fixed try to keep equipment idiot proof. That was obviously a “Single use” clevis pin. Not a nail.
@johnwilliams4545
3 жыл бұрын
Your comment on American made are on point, 'Too lazy and Too cheap'. The same holds true here in Australia.
@Tom-In-Ga
3 жыл бұрын
Have to agree with you John. Wes's "Too lazy and too cheap" rings true. I always try to buy American, in your case, Australian. I'm sure there are guys like us in other country's who try and do the same. I feel its always better to support your own country's manufacturers first. Then, if you can't find it, look elsewhere. But, its getting harder and harder to do that since so many of our mfg's have exported their manufacturing outside and make it look like it's "home grown". John Ruskin said: “It's unwise to pay too much, but it's worse to pay too little. When you pay too much, you lose a little money - that's all. When you pay too little, you sometimes lose everything, because the thing you bought was incapable of doing the thing it was bought to do. The common law of business balance prohibits paying a little and getting a lot - it can't be done. If you deal with the lowest bidder, it is well to add something for the risk you run, and if you do that you will have enough to pay for something better.”
@clarencewiles963
Жыл бұрын
Thumbs up 👍
@kenmccormick3052
3 жыл бұрын
vertical down is a problem with a stick using something like a 7018 rod, high slag inclusion in your weld. Think the MIG freezes fast enough that the slag--[what there is] do not have time to flow down into the molten weld material below. hope that makes some sense to you.
@CrazyPetez
2 жыл бұрын
I like how you store that crankshaft correctly upright. Some Internet fools think a crank should be laid horizontally to prevent bending. Exactly wrong.
@timmybob4871
3 жыл бұрын
C'mon Wes, put a big ass log on there!
@kenmccormick3052
3 жыл бұрын
double the thickness is a good move.
@reviewking9709
2 жыл бұрын
those screws at 6.56 just weld some nuts on them
@bahopik
4 жыл бұрын
There's this one guy that works at a place that buys bearings wherever they can get it cheap, then machine off numbers and brand names and engrave their own numbers and "Made in USA" so just cause it says on it there's no guarantee
@gerin1946
3 жыл бұрын
Friend !!! on the wedge, put some small wedges to split in 4 pieces not only 2 pieces !!! ---- Of center wedge is not all that good especially when you get stumps with branches knots which are very strong splitting !
@joseortiz5965
3 жыл бұрын
Awesome
@hddm3
4 жыл бұрын
How dare you call me lazy! Hahahhahahahhah. True true
@paulsilva3346
4 жыл бұрын
HEY WES, what about the motor oil, and the hydraulics Maintainance...???
@DoRC
5 жыл бұрын
The etemology of plug nickel is interesting.
@WatchWesWork
5 жыл бұрын
You've got too much time on your hands!
@DoRC
5 жыл бұрын
@@WatchWesWork Yeah. I'm fighting Lyme disease. It leads to way too much laying around.
@Pico2199
2 жыл бұрын
Who the hell said you can't weld vertical down. It's fine, in fact this is a good case for it. The thinner base metal with bend or break before any properly made vertical down weld would. And yeas, I know how old this video is.
@shackman9566
3 жыл бұрын
Thanks again Wess.
@critic482
6 жыл бұрын
Great videos, some ptfe "cutting boards" might help to stop the destruction.
@WatchWesWork
6 жыл бұрын
I've never seen any kind of bearings on a log splitter, but it does seem like a good idea.
@critic482
6 жыл бұрын
Wes Johnson, I know I have seen then only on a few and most don't come to mind. Quick Google search bring up this one. It has nylon slides as one of its listed features. shop.spectrum-plant.com/default/bf-a16or1060pi.html
@critic482
6 жыл бұрын
might be only a UK thing as here is another one, that uses brass slides. I know i have seen one in person here in northern indiana. www.fourseasonsfuel.co.uk/log-splitters/amr-vertical-log-splitter-v-h-12-tons-14-0-P-75/
@paulsilva3346
4 жыл бұрын
I use BAR lubricant on log splitters...
@toddavis8603
2 жыл бұрын
Illinois log splitter after Abraham Lincoln!!"
@deenunya7735
3 жыл бұрын
Theres something very Theraputic Wes Using a Log Splitter , cant beat a Blazing Log Burner Fire 👍
@bigmikex2333
3 жыл бұрын
Dude that's a Millermatic 200 the 44 Magnum of mig welders! 3/8 to 3/4 isn't even gonna make that thing break a sweat.
@shaneharrison4775
3 жыл бұрын
Dont forget to gusset the foot support and make your log stops heavier
@jimlong527
3 жыл бұрын
Nothing like bringing our the torch. You can practice to cut up recycling cruise ships in your part time with wife as a team.
Пікірлер: 187