I have had one for a while and it's still working fine.
@martinkuliza
Жыл бұрын
6:56"that's your sign that powers going to it " ACTUALLY IT'S NOT it actually has a meaning 3 Dashes (Depending on which side they appear on) means.... THE UNIT IS GOING INTO STANDBY MODE 9:28 "the company recommends you leave it on the full amount, basically " ACTUALLY THEY DON'T What they say is.... To ensure longevity of life they recommend turning down the heat and increasing the windspeed , but keeping it as low as possible so as to not unnecessarily load the unit. They don't say crank it up, they say , Try and keep the Temp down as much as possible Increase the windspeed instead, but only as much as is necessary I've got mine on 5.5 Speed works fine
@summerishere2868
2 жыл бұрын
I also got one of these for my work is good enough. I bought some proper tips though, the ones that came with the unit were so cheap that some burned out on the first usage. With good tips it works well, the hot gun is pretty good as well.
@dlacicagaming4799
2 жыл бұрын
What tips did you buy? Does it fit from other soldering irons?
@summerishere2868
2 жыл бұрын
@@dlacicagaming4799 "LUXIANZI", "900M" model with "Plating Film".
@edward_grabczewski
4 жыл бұрын
Just bought one too. The soldering iron temperature settings were innacurate by anywhere between +25 and +35 degrees C, othewise it's okay.
@Millzieeeee
4 жыл бұрын
negligible when iron should be hot as possible (before degrading chinese tips) to get in heat a pad add solder and get out yknow , so yeah , ill be fine with that fluctuation of 30 degrees
@bblitefootbilly3243
4 жыл бұрын
thanks for the vid as im looking for a cheapo unit ... some sellers charge 3x the price for very same units so wouldn't be nice paying top wack for whats in fact a budget type!, so il stick with getting cheapest i can find as im just tinkering atm lol
@lucky-qr3tk
4 жыл бұрын
2 years down the road how is this unit holding up whats the issues would love a comment update or even a video any problems happen with the unit ?
@jsa2001
4 жыл бұрын
Yes everything is still working fine apart from the heat blower it only lasted 6months as the heating element died in it.
@Saint696Anger
3 жыл бұрын
@@jsa2001 cool I just ordered this and am excited to receive it 😊
@rainsnow9174
Жыл бұрын
Thankyou for the review, just bought this exacy one for a small project to fix chip on board. Very rear I use soldering, but I've always found myself ive needed a station combo like this for the job on electronic chips and heat gun don't cut it for electronic tiny chips without control of air speeds.
@CiderPang27
3 жыл бұрын
Piece of junk. Got one, power lead wouldn’t even fit in it. Sent it back for a refund and bought a different make altogether.
@fajeidea
Жыл бұрын
Apakah alat ini memiliki mode standby sleep ketika gagang solder dan gagang solder uap di simpan di tempat nya.tx
@laupert9021
3 жыл бұрын
I have on of these and been using it an almost daily basis for half a year now. Unfortunately, the included tips are not very good. Any suggestions on where to get new higher quality ones?
@markharrisllb
3 жыл бұрын
I’m using copper tips at the moment as there's about 1cm between the end of the heating element and the tip of the tip. The cheap stainless steel tips don't seem to transfer heat well enough. I'm still a newbie though and if someone more experienced comes along with better advice I'd follow their's.
@laupert9021
3 жыл бұрын
@@markharrisllb I just got original Hakko T18 tips and that was a completely different experience. Much better than the cheap ones.
@markharrisllb
2 жыл бұрын
@@laupert9021 Sorry, I should have come back to this comment months ago. I’ve been using the T18-B tips, thank you for the advice. It’s the same price for one as half a dozen cheap ones but worth it.
@markharrisllb
2 жыл бұрын
Have you seen the price of the now? There’s two sellers on eBay selling then for £88! Mine was £38 last year. I’m pleased with mine but I’m not sure they’re worth £88.
@Alexander_l322
Жыл бұрын
Bollocks I just paid 70 quid for mine on Amazon! I couldn’t find one cheaper. I’m pissed lol
@rainsnow9174
Жыл бұрын
@@Alexander_l322 just bought one for £48 guess cost of living went up since you bought it
@lucky-qr3tk
4 жыл бұрын
thank you for the video legend it
@agw5425
2 жыл бұрын
It would be nice to hear if you think it is worth the 60£ it costs(or did you get it for less?)
@jsa2001
2 жыл бұрын
Mine is still working, it was cheaper when i bought it, everything is more expensive now due to inflation.
@itzzkingzz30
3 жыл бұрын
Hi i have the same unit as you i have only had it for a couple of weeks now and the hot air is not working when i turn it on it sits on 8 and wont go up any higher then that would you have any idea on what's wrong
@martinkuliza
Жыл бұрын
Have you opened it to take a look inside. What could be wrong could be a variety of things
@hologram94
5 жыл бұрын
Looks like a decent station, how was the soldering experience?
@jsa2001
5 жыл бұрын
The blower lasted 6months replacements cost about £14.00 from China or eBay. The iron is still working really well after heavy use, only gone through one tip. So I'm happy with the soldering iron.
@Jezza3110
4 жыл бұрын
But what actually needed replacing ? Fan ? Heating element ? Looking with a view to buy
@jsa2001
4 жыл бұрын
@@Jezza3110 Sorry for the delay in replying. Its the heating element in the blower that's dead, everything else works and is still working today.
@furiousdoe7779
4 жыл бұрын
Ho ften did you use it ? Daily , Weekly .....or continuous.....
@540i_be_fly
3 жыл бұрын
I have the same unit and for the most part I use it daily it is not a bad unit whatsoever unless you're nitpicker like other individuals
@fabrystyle7799
4 жыл бұрын
Hi there, Is it worth it compare to a 3 in 1 soldering station machine with power supply incorporated or not? I'm planning to buy this machine separate at one Bench Power Supply instead to buy one all-in-one as a YIHUA 853D. What do you think?
@jsa2001
4 жыл бұрын
They'll both perform similar and fail similar as most of these solder stations use the same parts when manufactured. I didnt need the power supply hence i buy the two in one. I can tell you my solder station is still going strong but the heat gun broke but they're very cheap to replace.
@geek4uaw
4 жыл бұрын
I’m sorry to say this but your voice reminds me or Kirk of Coronation Street, great video though
@asef698
3 жыл бұрын
Don't be sorry, just clean your ears out lad
@fredfarnackle5455
3 жыл бұрын
I bought a similar one (same but branded differently) and the driver for the hot air fan has died. Does anyone have a circuit diagram for this unit, or know what component to replace? The driver IC suddenly started being intermittent until it finally died - obviously heat related.
@jsa2001
3 жыл бұрын
Its most likely the heating element that's gone in the blower and not something in the main unit. You can buy them cheaply from China.
@fredfarnackle5455
3 жыл бұрын
@@jsa2001 No, it's the main unit, I took the hot air gun apart and it's fine and I also checked it by plugging it into another identical unit, it ran good on that. The main unit is stuffed.
@jsa2001
3 жыл бұрын
@@fredfarnackle5455 Try and locate the thermostat to see if thats gone.
@fredfarnackle5455
3 жыл бұрын
@@jsa2001 What thermostat, where?
@Millzieeeee
4 жыл бұрын
cant complain when one repair would pay off the cost of it :') i jsut bought one to replace my single 858d and a cheapo iron which works perfectly for hdmi port replacements , smc's refowing or removing components and chips with the 858d is perfectly fine too , but i wanted an all in one set up , and a iron holder that doesnt fall over to the weight of the handle of the iron hahahha! so we shall see how it goes when it arrives in a few days :D hope all goes well and let me know if its still working for you , have you been putting it through its paces as much as i would be ?
@Saint696Anger
3 жыл бұрын
Is it working good?
@Millzieeeee
3 жыл бұрын
@@Saint696Anger its solid , very happy its made me alot of money
@Saint696Anger
3 жыл бұрын
@@Millzieeeee good to know 👍🏻
@simonedl
4 жыл бұрын
hello can someone indicate the replacement of the stylus? I can not find thanks
@edward_grabczewski
4 жыл бұрын
Google "Hakko Station 900M-T 4mm Soldering Iron Tip". I bought some and they fit this one.
@vilv777
2 жыл бұрын
Same model i got.. But just dead today.. After one year....
@Turjak_art
4 жыл бұрын
so for you are 150£ low cost?
@jsa2001
4 жыл бұрын
Its not that price because the seller does not have it for sale anymore. Try here... www.ebay.co.uk/itm/2-in-1-Soldering-Iron-Hot-Air-Gun-Desoldering-Rework-Station-SMD-Digital-Solder/323927461365?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D1%26asc%3D20190212102350%26meid%3D1bac7158a8de418790eaca47c92b9e64%26pid%3D100012%26rk%3D1%26rkt%3D12%26mehot%3Dpp%26sd%3D273341418632%26itm%3D323927461365%26pmt%3D1%26noa%3D0%26pg%3D2047675&_trksid=p2047675.c100012.m1985
Пікірлер: 51