This homie is living the life. With oldies going in the back
@nolimitfabricationwelowrid159
2 жыл бұрын
Gots to keep the mind straight 🤣
@user-zv8gd3jl7q
7 ай бұрын
How much to reinforce a whole frame for 64 ?
@lifesgood4458
2 жыл бұрын
BAD ASS WORK HOMEBOY. THANKS FOR SHOWING US THE WORK OF TALENT. 💪🏽👏🏽👍🏽🙏🏽
@nolimitfabricationwelowrid159
2 жыл бұрын
Thank you
@budlight4206
2 жыл бұрын
Man your work is so clean always a beautiful job looking forward to seeing what you’re up to next
@nolimitfabricationwelowrid159
Жыл бұрын
Thank You 💪
@aldonco
2 жыл бұрын
True craftsmanship ,nice job brother
@nolimitfabricationwelowrid159
2 жыл бұрын
Thank You 👍👍
@nolimitfabricationwelowrid159
2 жыл бұрын
Thank You 💪
@phreaktor
2 жыл бұрын
What thickness is that on the outer arches and the main rails? What method do you use to bend your parts? A rosebud on a torch and heat it up till you can hammer it with a mallet? Nice work homey. I’m stuck out here in Jersey building my 82 Monte with no help or guidance because no one wants to give up info not even the shops that I bought parts and kits from smh. KZitem is my only resource at this point, so I appreciate you showing all this.
@nolimitfabricationwelowrid159
Жыл бұрын
3/16" on arches 1/4" on rails
@rsonweb2060
Жыл бұрын
Nice looking welds.
@ericchavez6053
Жыл бұрын
this is sick! can you do a video of how you do the pockets and inside where the donuts go?? for a gbody
@thecadillacdanshow8658
2 жыл бұрын
Bad ass work!
@nolimitfabricationwelowrid159
2 жыл бұрын
Thank You 👍👍👍
@ryaneast7125
Жыл бұрын
Clean clean clean
@evanpimental
Жыл бұрын
You do really good work! Where is your shop? I'm in Sacramento.
@reygomez323
Ай бұрын
What weldr are you useing
@BeatrizGarcia-hh6ys
11 ай бұрын
I have a 63 frame I want to use on my 1964, I'm not ready for hydrolics yet but I want to do the frame first...I want it to be strong enough to handle as crazy as I want to go... I would like a rough estimate to do my frame like that...? How do I get in contact directly with you to get a time frame, deposit amount, etc.?
@spaceportprojects6078
Жыл бұрын
What’s up with the bridge to axle alignment ?? It doesn’t need to be straight up and down ?
@bizzib4
2 жыл бұрын
🔥🔥🔥CAM- MOAN !!!💯
@nolimitfabricationwelowrid159
2 жыл бұрын
💯
@NoiseBoysGarage
2 жыл бұрын
How much reinforcement does my frame need on a78 tbird only 3 pumps 4 batteries. Looking for baby hop and 3 wheel
@nolimitfabricationwelowrid159
2 жыл бұрын
4 corners & front face belly
@tompark3092
2 жыл бұрын
I have a 1995 big body Cadillac Fleetwood want to Put in a lay n play a six battery two pump set up how much reinforcement do you think I need
@barbarahernandez6264
2 жыл бұрын
I need some work done on my lowrider homie but im in El Paso tx
@nolimitfabricationwelowrid159
2 жыл бұрын
My O.G. Homie a hotshot driver stays in Fort Worth Texas. He can provide transportation not a problem.
@joserozay213
Жыл бұрын
Nice.. Question.. Is a 3 sided frame wrap sale for 3 wheel and some hop in a 63 impala? Asking cus my buddy got a car which is 3 sided reinforce
@nolimitfabricationwelowrid159
Жыл бұрын
Yes you can play with it
@joserozay213
Жыл бұрын
@@nolimitfabricationwelowrid159Thank u for replying man..
@joserozay213
Жыл бұрын
@@nolimitfabricationwelowrid159is all reinforcement good or it gota be a specific thickness to it
@dglopez12
11 ай бұрын
Wats up man good work I’ve been watching your videos but how do we get estimates I have my 83 regal I’m working on the engine I was thinking of taking just the frame to someone to reinforce and make it hydraulic ready nothing big or show just reinforced for family cruising, 3 wheel and maybe now and then a small hop to show off you know what I mean… mostly family fun cruiser. But yea I don’t see how to get in touch if it’s possible…
@dglopez12
11 ай бұрын
And I mean the frame that can still roll around I would take off the body and I already have engine and trans out it’s just my project I’m a mechanic but I don’t weld or fabricate so this video caught my attention I would transport it to you..
@original8616
Жыл бұрын
If I have a lay n play setup do I need to reinforce the arches or stress points ?
@nolimitfabricationwelowrid159
Жыл бұрын
4 corners to protect the frame
@original8616
Жыл бұрын
Koo thxs
@Ovniware33
2 жыл бұрын
Is that 1/4 inch or 3/16th thick plate and is 3/16th plate suitable for reinforcement??
@nolimitfabricationwelowrid159
2 жыл бұрын
Frame is 3/16" plated Bessey C-Clamps Are King the Big Dogg Ones For Applying metal to frame.
@Ovniware33
2 жыл бұрын
@@nolimitfabricationwelowrid159 thanks 😊 Looks bad ass. Nice work 👍
@prettyshield5540
2 жыл бұрын
You get down homie how much does this run and did you reinforce it so much becuase it's a hopper frame?
@hosscaddy
Жыл бұрын
How did you make your templates
@nolimitfabricationwelowrid159
Жыл бұрын
Box or thick ass drawling paper Press up against frame with baby c clamps then trace out with a marker
@hosscaddy
Жыл бұрын
@@nolimitfabricationwelowrid159 nice. Your plates and welds look crispy clean
@nolimitfabricationwelowrid159
Жыл бұрын
@@hosscaddy thank you. Been fabricating for 17 years fuckin over it 🤣🤣🤣🤣
@rudyg7409
Жыл бұрын
How can i reach you
@luisangulo9974
Жыл бұрын
How much you'll charge me to do my frame on a 84 Cutlass
@AIVega
7 ай бұрын
Exceptional product. Excellent video. Great content. The best of KZitem. Like, Share, subscribe. Promote and engage. Outstanding review. Recommend. Gold. Tremendous entertainment. Economy motivational AI Chess Military Frugal Documentary high quality backlinks captivating gaming beast
Пікірлер: 50