I bought a dished flexplate and used the 480l spacer on transmission side of the dish ..easy peasy ...
@michaelchristian6657
2 жыл бұрын
This is one of the best KZitem videos I have ever seen. Thank you for sharing your knowledge!
@tjgreer2661
2 жыл бұрын
Great advice. I am running a 1999 5.3 in a s10 with a 4l60 from the s10 could not understand why convertor didn't line up with flexplate till I watched you video. Lots of information explained in a way it can be understood easily. Thank you for sharing your knowledge.
@mountainsgarage
2 жыл бұрын
Thanks! I have made a few recent videos about the same subject, finding better ways to do it.
@kylealexander1172
Жыл бұрын
@@mountainsgarage which videos please?
@martysheets6882
2 жыл бұрын
Shawn thanks for the information, I had trouble with the depth with the small spacer just like you said.Thanks Marty.
@MrLangleylad
3 жыл бұрын
Congrats on 50 Shawn , you're teaching us all a thing or two and that's always a good thing . Thanks from Langley , BC
@mountainsgarage
3 жыл бұрын
Love that you are watching!
@MrLangleylad
3 жыл бұрын
Mountains Garage you keep putting them out and I’ll keep watching !
@davidsmith4009
2 жыл бұрын
Just came across your channel. Very informative. I’m building a 5.3 and mounting a 4l80e behind it. Thanks I am now a subscriber.
@mountainsgarage
2 жыл бұрын
Welcome aboard!
@michaelanderson5108
3 жыл бұрын
Thanks Shawn! I’m enjoying all these videos, and I’m thankful for you taking time to do them
@mountainsgarage
3 жыл бұрын
Thanks for watching!
@jimbowman7751
2 жыл бұрын
ty ive wàtched alot of videos trying to figure this out with the new flexplate i bought .not 1 of them showed the diff.between the 6.0 and the Ls versions except your video.ty so much
@martysheets6882
2 жыл бұрын
Shawn just watched your video again, and I'm thinking anyone that makes and takes their time to make straight up Damn good videos deserves a subscription, so now I won't miss one.thanks again Brother.
@mountainsgarage
2 жыл бұрын
Thank you!!
@jasonjennings5833
2 жыл бұрын
I love this channel. Glad I found it. I’m from Tennessee and I like your accent.
@mountainsgarage
2 жыл бұрын
Thanks! What accent?? :)
@kennethharms7503
Жыл бұрын
doing a ls swap for the first time thanks for the video straight to the point with no bull shit. I like your style
@jonathanmoore5112
2 жыл бұрын
Finally got the answer I’ve been looking for. Thanks LS2 to 4L80e
@nyertsenginetransmission3861
3 жыл бұрын
Thanks for the videos man I enjoy learning stuff i havent ran into yet.
@mountainsgarage
3 жыл бұрын
Glad you are enjoying them!
@tomanderin17
28 күн бұрын
thanks for the video. i've got an l96 6L from a 2011 chev 2500 and a 4l60E from a 2002 chev 1500. which flywheel would i need. thanks
@brandmejia7151
3 жыл бұрын
I have a lr4 with the extended crankshaft I’m wanting to use a t56 on it what flywheel could I use to make them match up thanks
@josegutierrez2872
2 жыл бұрын
Saludos veo que estos tutoriales son muy completos...Pero les falta la traducción ... Gracias 🙏
@richardkarsten70
2 жыл бұрын
That helped me a little now i know it has 3 bolts but I have a question about my flywheel
@timdontwannasay5889
2 жыл бұрын
Thank you! Learned my something new for the day!
@user-tl4zl5ib7n
6 ай бұрын
Hey do you have any insight to how I could get a 99-00 lq4 6.0 to my nv3500 in my Chevy half ton
@mountainsgarage
6 ай бұрын
You likely have the +.400 crankshaft so a flywheel from a similar vintage Camaro/ Firebird will work.
@robinktabares
10 ай бұрын
Can you use the flat one on a Dodge2500 automatic v8 5.9 or do I have to use the dome????
@MrRichStephens
2 жыл бұрын
Shawn read this, Here is what I found. I have a 1995 5.7 that has a 4L80E. I am putting the 1995 motor into my 1990 Chevy van that has a 305 and a th400. I also found a balance plate on the 4l80E flex plate. The flex plate came with the 95, 5.7 motor. The 95 motor is a roller cam engine, after looking into the numbers of the first Gen1 Vortech motors, Which is what I was after. The flex plate with the balance plate being on the 95's flex plate has me puzzled?? I am thinking when I use the th400 torque converter and transmission of leaving the balance plate. Which I think I should. Has anyone else seen anything like this?? I don't want to remove that balance plate cause it may have something to do with the balance of the engine. What to do, what to do..
@mountainsgarage
2 жыл бұрын
All one piece seal SBCs are external balance on the flexplate end. The 4L80E and TH400 should have the same converter bolt pattern. Should be a simple swap.
@ron7922
Жыл бұрын
Hi Shawn, I have a 02 lq4 with the flat plate and spacer if I'm not mistaken my 06 4l60e should bolt right to it. am i wrong?
@mountainsgarage
Жыл бұрын
Yes the 4L60E converter spacing is LS depth, not Legacy Depth. So it will not work with the 6.0 set up.
@joshuascales7475
3 жыл бұрын
When you talk about the spacer that goes in between the converter and the flexplate @ 7min and 50 sec... do you know a part number for that or what they would refer to it as?
@mountainsgarage
3 жыл бұрын
It’s a Summit Racing SUM-704000, Jegs 601010, add a K and you get the bolts. Others such as ICT Billet make them as well. Thanks for watching!
@Snailmailtrucker
2 жыл бұрын
Is there a difference in a TH400 Flexplate and a 700R4 flexplate on a 1982 Chevy 350 engine ? I just swapped the TH400 out of my old 82 Chevy 350 cu.in. Cube van and put in a 1991 700R4. I had the driveshaft shortened and a new 27 spline Slip yoke installed...It bolted right up...but I am getting a rumbling noise near the Torque Converter....not sure what it is... I haven't taken it out on the road yet... as I don't want to make things worse !
@mountainsgarage
2 жыл бұрын
If the torque converter bolted up to a set of holes, then it’s correct. Is the cover hitting?
@Snailmailtrucker
2 жыл бұрын
@@mountainsgarage Thanks for the super fast reply ! No, nothing seems to be hitting anywhere that I can tell. Was worse a few days ago... Weird !
@Snailmailtrucker
2 жыл бұрын
Real noisy today... I think I gotta pull that trans out and see what is wrong !
@bradykosar
Жыл бұрын
Great info. Thanks!
@rawouch
4 ай бұрын
Which flexplate for a LS 6.2 to a 220-4R?
@jordantovar6855
3 жыл бұрын
I Have a 4l80e on my 1999 crew cab obs k2500 had a 5.7. Swapping out to a lq9. Please what flex plate do I need. What truck,car,Years look into to get it
@mountainsgarage
3 жыл бұрын
With a stock converter the 4.8 or 6.0 crank spacer and flat flexplate is the best option. Find them in Vans and 2500/3500 trucks.
@lukeleslie1122
2 жыл бұрын
Shawn. I'm swapping a 2000 LS1 infront of a 4l60e. What flexplate should I use, you said that these engines didn't take the extra spacing into consideration
@lensbarbershop8760
Жыл бұрын
Great video. Glad I found you . Im putting an old sm465 manual behind a long crank 2000 6.0 l . Which flywheel and clutch should I purchase (on a budget) fairly stock hp build? Just a stock flywheel from like a 2000 chevy 1500 truck ?? Thanks for your time.
@mountainsgarage
Жыл бұрын
You want the flywheel for a 2000ish Silverado 6.0 It will have the .400 thickness built in. It takes a 12” clutch. Usually $100 or less.
@lensbarbershop8760
Жыл бұрын
@@mountainsgarage probably the same as like a 1999 with the 5.7? I cant seem to find a 2000 ish with a manual to search ..
@JonOffgrid
2 жыл бұрын
thank yea i have a 700r4 i hope i can find the right parts
@funfun8095
3 жыл бұрын
👍
@MD-cd7em
2 жыл бұрын
GOOD DEAL...SUBBED!
@mountainsgarage
2 жыл бұрын
Welcome aboard!
@zacharygray5608
3 жыл бұрын
Does the flat flexplate apply to a ls3 mated to a 4l80e?
@mountainsgarage
3 жыл бұрын
As far as I now the crank stick out has remained the same, so yes.
@montecarlo6.0turbo
2 жыл бұрын
I had a dish flywheel on my 09 truck and put a flat one on and stater sounds like shit
@mountainsgarage
2 жыл бұрын
The flat flexplate has the factory spacer between it and the crankshaft?
@gerardolopez5875
2 жыл бұрын
Will 60E last on a 6.0 liter???
@robertweitlauf4653
3 жыл бұрын
never mind,🙊🙊🙊
@mountainsgarage
3 жыл бұрын
?
@robertweitlauf4653
3 жыл бұрын
@@mountainsgarage im just over thinking thing the hub adapter.
@gerardolopez5875
2 жыл бұрын
@@mountainsgarage @amigo,, whats the part number? Or description ?? Flex plate
@brian7189
Жыл бұрын
Seek Jesus! He’s the way! The truth! And the life! Repent for the Kingdom is at hand!
Пікірлер: 62