I bought my TJ with the sole intention of LS swapping it. After building a few Jeep inline stroker motors I will NEVER waste the time or money on an LS swap. My TJ is built exactly like a friends , the only difference is his has a Corvette 5.7 LS , cost $10,000 and a hundred hrs to build, and mine has the original engine built and stroked to 4.6. They run side by side on the drag strip and mine makes torque much lower in the rpm range which helps offroad. I didn't have to run adapters, piggyback or stand alone ecm's , don't have packaging problems, cooling issues, and I can run my original air box instead of a crappy open element filter that should never be on an offroad vehicle. Unless you are running tons and 40" tires or larger there is no reason to LS swap , unless you just like wasting time and money. There is also no better feeling than blowing the doors off a V8 swapped jeep with a inline 6 cylinder at the dirt drags.
@jeepspeedshop
2 жыл бұрын
We are no longer doing LS swaps, sorry.
@bdd1469
2 жыл бұрын
@@jeepspeedshop Obviously you are also no longer READING COMMENTS.
@jeepspeedshop
2 жыл бұрын
@@bdd1469 I get that part, we have had some problems with stoker 4.0L engines. We do not see many Jeep's older than 2006 anymore. The 4.0L Jeep is slowly slipping away, everyone wants the 4 door Jeeps and a new group of problems.
@oneshoeboxer8
2 жыл бұрын
I've been looking at a Golen 4.6. I feel like building my own stroker might be out of my shade tree abilities. Is yours home made or a bought one?
@nalley6815
Жыл бұрын
If it cost him $10k to build, he wasted his money. For $10k I could have one swapped AND making 700hp with EASE. Any LS swap not using a truck engine is a waste of money.
@kingdotsize86
5 жыл бұрын
but wait,,,,, is it runnning?
@jeepspeedshop
5 жыл бұрын
Hell Yeah and running great, This Jeep is a sleeper.
@deegan727
5 жыл бұрын
Sarcasm seems to be a dieing language.However I do my part to keep it alive also.
@JeepTJay6
5 жыл бұрын
deegan727 🤣😆😂 shhh I’m listening...I can’t hear if it’s....wait...is it running? 🤣
@beunbad
3 жыл бұрын
How’s it do on fuel mileage?
@BigRandyR
5 жыл бұрын
I need mine done now!! Awesome
@germaned.lealnino631
3 жыл бұрын
How much was the conversion? Roughly.
@mach5jeep
5 жыл бұрын
How come non of these conversion videos on KZitem address the transmission mount, driveshaft lengths, etc?
@jeepspeedshop
5 жыл бұрын
We build the 6l80 transmission mount adapter and reuse the TJ rubber mount, Like on this Jeep we put a Dana 44 in the rear and a slip yoke eliminator. On a TJ we never reuse the stock drive shaft in the rear, we do reuse the front drive shaft.
@djbarker3665
2 жыл бұрын
Very awesome. I have a stock 2006 tj, been considering. Is there a ballpark figure?
@jeepspeedshop
2 жыл бұрын
We do not really do LS swaps any more
@djbarker3665
2 жыл бұрын
@@jeepspeedshop thanks for the reply, sad though.
@jorgezuni2818
5 жыл бұрын
Need a Get mine legal LS with California smog certificate
@evansautomotive307
4 жыл бұрын
Just needs to be newer than the car your swapping it into, needs rear o2 sensors and an evap system and cats of course. It also helps if you have a friend in the system! Hahah
@redheadedstepchild4130
6 ай бұрын
I wanna do a 5.3 in my 05 LJ, but have the 42rle. Is that safe to keep with the potential hp? I'm not afraid to get on it with the 4.0 and 37s but I worry about it with a built engine and 40-42s. I've got wontons sitting and waiting, i just wannaget my ducks in a row
@jeepspeedshop
6 ай бұрын
We no longer do any LS conversions. But if i were to do a LS in a Jeep i would not use the Jeep 42RE transmission, I would go with the 6L80 transmission
@mhi7340
6 ай бұрын
How about 4l80e trans with good trq converter ? @@jeepspeedshop
@nickr7739
5 жыл бұрын
I just got a the 1999 I would like to get some knowledge on this project please advise with further details.
@nickr7739
5 жыл бұрын
Please get to me at ur earliest convin
@jeepspeedshop
5 жыл бұрын
Just so you know this is not smog legal in California right now, we use a L99 out of a Camaro and the 6L80 transmission. Used, we could do it new also.
@jesusgonzalez-cr5bu
Жыл бұрын
hi i have a jeep lj rubicon with a nsg370 transmission i would like to do that conversion how did you get all the stock gauges to work with the LS engine? do you sell a kit?
@jeepspeedshop
Жыл бұрын
We don't really do LS swaps anymore, but to get the gauges to work we ran the Jeep computer and sensors
@mikemyers9093
5 жыл бұрын
is it running ?
@germaned.lealnino631
3 жыл бұрын
I think is running
@bustamantealdo
4 жыл бұрын
do you have the buil;d on ant fourms? or parts list?
@vincentm9372
5 жыл бұрын
Wouldn't work on my 2005 TJ Rubicon.I have that elusive cam& crank sensor problem.
@anthony4x477
4 жыл бұрын
Nice project, im trying to do the same project here in nj and i will loke to know where you got the kit from, im pulling my engine from a avalanche do i need the whole harness waaring transfercaese and transmission of that truck thanks
@jeepspeedshop
4 жыл бұрын
We built the conversion kit (Jeep Speed Shop)
@anthony4x477
4 жыл бұрын
@@jeepspeedshop how can i get in touch with you. I will like to be closer to you but im in nj. Also i want to now if i can use the same wiring to romove it from the avalanche and the transfercase
@lukesmith8482
2 жыл бұрын
Would you guys do the LS swap just like this one for the right price and not having to deal with emissions ?
@jeepspeedshop
2 жыл бұрын
I would have to see what we can do, it has been awhile now.
@rickolivasone4790
Жыл бұрын
How much to LS swap a 97 tj with me already having the donor vehicle. Ball park price.
@jeepspeedshop
Жыл бұрын
We no longer do LS swaps, sorry
@larrylawrence2222
2 ай бұрын
No body lift?
@jsflagstad
5 жыл бұрын
Where is the kit available? 2004 TJ Rubicon, I have the 5.3 and am ready to go.
@jeepspeedshop
5 жыл бұрын
In our store at Jeepspeedshop.com
@jsflagstad
5 жыл бұрын
@@jeepspeedshop I see no LS to TJ Swap kits listed on your site
@leonelceballos3709
3 жыл бұрын
Thinking on doing a swap on mine, how much am I looking to spend on a swap like this
@aidencruthirds5005
3 жыл бұрын
5-15k
@toxicplague6278
Жыл бұрын
Wish y’all still sold tj adapter kits
@jeepspeedshop
Жыл бұрын
Sorry we just have had to many problems with a LS in a Jeep so we just stopped, We only work on 2008-2018 Jeep JKs anymore
@smartassjeff1
5 жыл бұрын
So with a truck LS you don't have to change the alt-nator? Which do you recommend?
@jeepspeedshop
5 жыл бұрын
We have done many LS Truck engine and used the truck Alternator, but we have found using the Trail Blazer Alternator and power steering bracket works best, so than you can reuse your power steering pump and it is higher up.
@jaredsletom3446
2 жыл бұрын
What modifications did you have to do to make the factory shifter work ?
@jeepspeedshop
2 жыл бұрын
Well on the Jeep we used the 6L80 and the stock Jeep cable worked, now this Jeep had a 42RLE transmission and the cable worked great. We have a cable mount for the 6L80 and the newer TJ
@the_junkdrawerTCG
2 жыл бұрын
Did you say it was running?
@user-gd2lz1pk5d
6 ай бұрын
What part number are the rad hoses?
@jeepspeedshop
6 ай бұрын
LS parts Mass Air Flow Sensor Mount (GM Part #: 19166574) Mass Air Flow Sensor -Works with GM Part #: 19166574 (GM Part #: 15865791) Quantity of 2 - O-2 Sensors - Upstream (GM Part #: 12583804) Quantity of 2 - O-2 Sensors - Downstream (GM Part #: 12609457) Quantity of 3 - Torque Converter Bolts (GM Part #: 11589040) Crank Shaft Bolt (GM Part #: 12557840) Transmission Cooler Lines (GM Part #: 92236244) Right Trailblazer Exhaust Manifold (GM Part #: 12600527) Left Trailblazer Exhaust Manifold (GM Part #: 12600526) Gas Pedal (GM Part #: 25832864) Heater Hose one end of hose is 3/4″ & the other is 5/8″ (Napa Part #: 10084) Power Steering Hose that works with GM Truck Power Steering Pump (Napa Part #: 7-3392) Upper Radiator Hose (Gates Part #: 21821) Oil Block-Off Gasket (GM Part #: 12611384) Oil Pan Block-Off Plate for JK Oil Sender (GM Part #:12551587) Mass Air Flow Sensor with honey cell (GM Part #: 15900023) Mass Air Flow Sensor without honey cell (GM Part #: 15900024) Mass Air Flow Sensor works with 2009-2012 GM Truck (GM Part #: 10393948) Transmission Isolator (Chrysler Part #: 52059945AB) Brake Booster Nipple (GM Part #: 12559760) Quantity of 2 - Exhaust Manifold Gaskets (GM Part #: 12617944) Exhaust Flange Gasket - Driver Side (GM Part #: 15077362) Exhaust Flange Gasket - Passenger Side (GM Part #: 15035747) Trans seal 24238076 Oil cooler plug for the block 11609289 GM TWO ,1/2 inch plugs Trans dip stick, tube and seal 24267668, 24260606, 15796802 Upper Radiator Hose (Gates Part #: 21821) Jeep JK with L99-LS3 engine Crank Shaft Bolt (GM Part #: 12557840) T case cable mount 52121832AC, Jeep JK Camaro Belt GAT K060854 Camaro power steering pulley 1261079 power steering pump mount 12610792 bolts 11588725, 12557840, 11588747 for power steering Trans mount GM Truck mount for Atlas ANR 2638 Dodge Ram oil sender 05149097AA Auto Meter Metric adapter 2277 Gates upper hose L99 JK 21588 21534 gates hose
@elblancochingon8138
3 жыл бұрын
But....is it running!?
@dad3562
10 ай бұрын
Got any videos of driving ?
@jeepspeedshop
10 ай бұрын
Sorry i do not
@RileyMy5090
5 жыл бұрын
Did you use a Tach emulator? Both computers to use stock gauges?
@jeepspeedshop
5 жыл бұрын
We did use the Jeep computer to run the gauges and we build a tone ring for the crank so you will reuse the crank sensor to get the tach to work. This is the best way to do this so if you have a problem with the tach it is probably the crank sensor, it would be a easy fix.
@mikepednault5678
4 жыл бұрын
@@jeepspeedshop do you have to remove the crank to install the tone ring? Do you sell just the ring? I'm about to dive into a 2004 TJ 5.3L swap and want to retain my factory tach!
@stevebillow395
2 жыл бұрын
Any info on the wire harness
@jeepspeedshop
2 жыл бұрын
We do not build it anymore, sorry.
@chopperbuilder70
4 жыл бұрын
Are you still doing TJ/LJ swaps? On the webpage all I see is JK/JL.
@jeepspeedshop
4 жыл бұрын
It is hard to find a 2003-2008 Dodge Ram Truck hemi
@chopperbuilder70
4 жыл бұрын
Jeep Speed Shop , what about LS swaps?
@abrahammunoz2717
5 жыл бұрын
How did you do the speed? I have an xj and cant figure it out
@jeepspeedshop
5 жыл бұрын
Do you mean the speedo, that should work.
@abrahammunoz2717
5 жыл бұрын
@@jeepspeedshop sorry I really ment the tach.
@jeepspeedshop
5 жыл бұрын
@@abrahammunoz2717 Tone Ring needs to be added to the crank pulley and reuse the crank sensor from the Jeep.
@abrahammunoz2717
5 жыл бұрын
@@jeepspeedshop does that make the milage and rpm work? Thanks for all your info by the way
@jeepspeedshop
5 жыл бұрын
@@abrahammunoz2717 RPM only, you would need to have the speed sensor in the T Case for the speedo.
@trentonverble8049
3 жыл бұрын
What wheels are on it?
@bsideadventures2180
4 жыл бұрын
Whats the ruff estimate on a job like that motor wise.
@jeepspeedshop
4 жыл бұрын
Doing a L99 and a 6L80 is about $25,000.00 ish depending on the Jeep.
@bsideadventures2180
4 жыл бұрын
That with drive shafts and cooling system sir?
@bsideadventures2180
4 жыл бұрын
Im not needing a air conditioning system. My main concern is cooling system and the motor not over heating
@mr.d7297
3 жыл бұрын
Did you have to shorten the rear drive shaft?
@jeepspeedshop
3 жыл бұрын
I don't think so, we ran a CV drive shaft.
@jeepspeedshop
3 жыл бұрын
I don't think so, we used a CV drive shaft
@elcompajr664
5 жыл бұрын
Nice video I have 1991 YJ best motors
@jeepspeedshop
5 жыл бұрын
2009 on up 5.3L or a 6.2L Gen 4
@elcompajr664
5 жыл бұрын
is a 1991wrangler v6 online
@simongetz6366
5 жыл бұрын
Looks good!
@groundpounder05
2 жыл бұрын
But, is it a sleeper?
@jeepspeedshop
2 жыл бұрын
Yes it is.
@Fritochiprt32221
5 жыл бұрын
How much for that install out the door? Talk me out of a hemi install.
@jeepspeedshop
5 жыл бұрын
Do you have a TJ
@Fritochiprt32221
5 жыл бұрын
@@jeepspeedshop I do, a 1997 TJ with a 2.5L.
@Fritochiprt32221
5 жыл бұрын
How much for an install?
@oscarbear7498
Жыл бұрын
How much was it $$?
@jeepspeedshop
Жыл бұрын
We did this many years ago and we don't do any LS swaps anymore.. I would think if we had to do this swap today it would be about $33K
@bryanspelhaug2135
5 жыл бұрын
What gear ratio are you running? 4.10's?
@jeepspeedshop
5 жыл бұрын
Yes we are running 4.10 gears and 33/12-50/15 tires
@elvynortiz3456
4 жыл бұрын
What's ur crusing rpm at 65 mph is a 6 speed and 410 gears so I'm working on same project nice beautiful built jeep men
@ItsMojoHQGaming
3 жыл бұрын
What’s with the ticking?
@jeepspeedshop
3 жыл бұрын
Injectors, this is a quiet engine.
@ramblin_man23
5 жыл бұрын
Was wondering if it's running or not.
@jeepspeedshop
5 жыл бұрын
Yes this Jeep was running, very quiet. Sleeper Jeep!
@ramblin_man23
5 жыл бұрын
Me and my buddy's starting to pull the old 4.0 out today. We got a 5.3 we're gonna put in it.
@jeepspeedshop
5 жыл бұрын
What year engine/transmission
@ramblin_man23
5 жыл бұрын
Not sure. He wants me to ask if a Walboro 250 fuel pump work on the stock tank? What did you use? Thanks
@jeepspeedshop
5 жыл бұрын
We use the 2005-2006 Jeep TJ fuel pump, the pump puts out 60 PSI.
@jimt.9227
5 жыл бұрын
The title is very misleading. "LS TJ the best LS Kit out there." You don't talk about anything like it's a kit. The title implies there's a set of components that comprises a kit. I was hoping for something that would offer something competitive to the pricey Novak options. But it's a sleeper... we get it. Done any YJ swaps? I've got a 6.0L going in my '87.
@jeepspeedshop
5 жыл бұрын
We have not done many YJs and the YJ does not really need a kit, you build it like a Hot Rod. Their is no Can Bus in a YJ so it is simple.
@jimt.9227
5 жыл бұрын
@@jeepspeedshop So this "kit" is about integrating the sensors into the TJ PCM?
@elcompajr664
5 жыл бұрын
4.0 on line
@ItsMojoHQGaming
3 жыл бұрын
Huh
@theluckyfishermen9594
Жыл бұрын
I don’t like that it’s quiet big v8 needs to be loud
@jeepspeedshop
Жыл бұрын
Kind of a sleeper..
@theluckyfishermen9594
Жыл бұрын
@@jeepspeedshop oh yeah still very cool just needs to be louder in my opinion 😂
@jeepspeedshop
Жыл бұрын
@@theluckyfishermen9594 I here you and that would be a easy fix..
@mbinnader
5 жыл бұрын
Is it for sale
@jeepspeedshop
5 жыл бұрын
Sorry this Jeep is not for sale, but we could build another one.
@fernandogarza1029
4 жыл бұрын
How much for the LS install?
@douglasabreland3930
3 жыл бұрын
@@jeepspeedshop hey man what's the contact information to get this set up on my tj
@jeepspeedshop
3 жыл бұрын
@@douglasabreland3930 We are no longer doing LS swaps
@chevrock22
5 жыл бұрын
I dont see you thanking Novak for any of this. lol
@jeepspeedshop
5 жыл бұрын
We are Jeep Speed Shop and we build our own LS kit. We do not need a tach convertor box, we use a tone ring on the crank and reuse the crank sensor from the Jeep to make it easier to fix down the road. Plus our kit is all new, we do not reuse wiring. The resin why we are not thanking Novak is because they did not help with any of this. This is why we build the best LS kit for the TJ. We make it simple for you the end user, YOU.
@bemyers123
5 жыл бұрын
chevrock22 I’m surprised that you haven’t deleted your stupid comment. I guess stupid is as stupid does? Oh, and the use of, “lol” makes you look like a child.
@abrahammunoz2717
5 жыл бұрын
@@jeepspeedshop how can you help with an xj? Would that tone ring work the same way?
@jeepspeedshop
5 жыл бұрын
@@abrahammunoz2717 Yes the XJ is the same has a TJ, we can help.
@SPPTA
5 жыл бұрын
Gas mileage??
@jeepspeedshop
5 жыл бұрын
The best this Jeep has gotten is 18 MPG, could get better, with some tuning.
@SPPTA
5 жыл бұрын
Jeep Speed Shop is that highway or combined? Wonder if it has the fuel management system. Cylinder deactivation.
@chrisd8837
5 жыл бұрын
I did a L59 truck LS swap in my Jeep and I get 23 mpg with the nv3550 trans, 3:73 gear and 35" tires..
@Bigtoe7272
5 жыл бұрын
@@chrisd8837 Do you have a video of it posted? Also, who did you use for marrying the LS to the NV3550. I am in the middle of a 6.0LS swap right now with an NV3550. How did it turn out and are you pleased with it? Any issues so far?
Пікірлер: 142