I'm really enjoying watching you rebuild, keep up the great work.
@RCBGarage
2 жыл бұрын
Thanks, I really enjoy doing the rebuilds. Much more to come.
@shonrob1620
Жыл бұрын
Been looking for a good informative video of the engine and you have a whole series very thankful 🙏
@RCBGarage
Жыл бұрын
Glad this video series can help you!
@spacetruckin6555
7 ай бұрын
Pissa job! That came out wicked mint! Now let's go to Friendly's and get some clam-chow-duh!
@jaeGroovin1091
5 ай бұрын
Great help n guide.
@RCBGarage
5 ай бұрын
Thanks
@13kentavious
Жыл бұрын
Is it best to build the top end with the bottom end ?
@RCBGarage
Жыл бұрын
If your replacing the crank I would do a top end also. Your putting a lot of time and money into the motor and a piston and rings are only $150 more to do. You don’t want to eat an old piston and ruin the motor. Plus the piece of mind as well as the performance is well worth it
@Crypto-Milly
5 ай бұрын
My LTZ pushes oil out of dip stick any idea what it could be ?
@RCBGarage
5 ай бұрын
Make sure the oil isn’t overfilled. Massive blow by can cause it also.
@bopboy7931
4 ай бұрын
I just bought a ltz400 and it’s in decent shape and I only gave 1500 it didn’t run but I got it working but the guy never said it had a cracked case and it leaks oil but there is jb on a place on the case where it looks like oil leaks, how much would it cost to split the case and get a new one or is it better to just put jb on it or I’ve even had people tell me to weld it, what should I do in your opinion, I don’t have much money put into it and I’m debateing if I should sell it or keep it but the crack in the case is keeping me from wanting to keep it
@RCBGarage
4 ай бұрын
Look on eBay for a set of cases. It’s not hard to do just make sure you have all the special tools to do it. And down load the repair manual. I have a PDF file of the manual. If you email me I will send it to you.
@bopboy7931
4 ай бұрын
@@RCBGarage i appreciate your feedback a lot, do you have to take the motor out of the frame or is it possible to keep it there in the frame
@RCBGarage
4 ай бұрын
@bopboy7931 you have to remove the engine. It’s bolted thru both the and frame in three places. It has to come out.
@bopboy7931
4 ай бұрын
@@RCBGarage is that an easy thing to do? Does it take a long time
@RCBGarage
4 ай бұрын
Watch the entire series on LTZ400 shows everything
@therealreaction2856
Жыл бұрын
how much for the work
@RCBGarage
Жыл бұрын
Email rcbgarage@gmail.com
@ahmedfreih334
2 жыл бұрын
Hello i did the same with my engine and when i rebulid it i can only change in 1 and second gear do you know what the problem is ?
@RCBGarage
2 жыл бұрын
Your transmission was probably assembled incorrectly. You will need to split the cases again. Down load the repair manual and follow the assembly drawings
@ahmedfreih334
2 жыл бұрын
@@RCBGarage okay thank you
@edwinmorales2329
2 жыл бұрын
Great content 👌, can you tell me where to buy the magnet puller and size thanks.
@RCBGarage
2 жыл бұрын
Edwin here is the link. Zinger 38mm Flywheel Rotor Magneto Puller M38 X 1.5 R.H. Right Hand Female Thread Flywheel Puller Remover Tool for Suzuki DRZ400/400S/400E|DR-Z400|Most GS/GN/GSX Street Bikes| LT240|LTZ250 a.co/d/8I4ofRI
@ahmedfreih334
2 жыл бұрын
When the case is split it’s going trough all the gears but when I closed it it’s only going trough 1 & 2 and neutral is it going to be like that? Everything seems to be according to the manual as well
@RCBGarage
2 жыл бұрын
You sound be able to find all the gears when you put the haves together
@ahmedfreih334
2 жыл бұрын
@@RCBGarage do you know what the problem could be?
@RCBGarage
2 жыл бұрын
@@ahmedfreih334 Your second trans shaft must not be assembled properly. You should be able once assembled to spin the output shaft (where the sprocket mounts) with your fingers and shift thur all the gears. If you can’t then you have it assembled wrong or you have bent or broken something during the assembly
@ahmedfreih334
2 жыл бұрын
@@RCBGarage does it have to be in a specific Gear when putting the case back together?
@R1Brooklyn
2 жыл бұрын
My new favorite channel.
@RCBGarage
2 жыл бұрын
Spread the channel and thanks for watching.
@damiantafolla9828
2 жыл бұрын
What parts would I need to rebuild the engine on a 05 ltz 400
@RCBGarage
2 жыл бұрын
What are you rebuilding, Top end only ? Top and bottom end? Once apart inspect everything and replace worn or broken parts.
@damiantafolla9828
2 жыл бұрын
I bought the piston and gaskets and the clutch because the old piston would leak oil and white smoke would come out of the exhaust
@RCBGarage
2 жыл бұрын
@@damiantafolla9828 do valve seals also.
@damiantafolla9828
2 жыл бұрын
How many valve seals would I need to get?
@RCBGarage
2 жыл бұрын
@@damiantafolla9828 Go into my video library. I have a video on how to rebuild the LTZ400 head.
@pugnboots5683
2 жыл бұрын
Nice job, this is why I love your channel you show the good and bad when working on motors. Very real life.
@RCBGarage
2 жыл бұрын
Not all of the builds go perfect. I heard the pin snap and I knew right away what it was. The transmission on the LTZ400 is a pain in the butt to re-assemble not the easiest engine to split.
Пікірлер: 46