The one key thing you left out was adjusting the pin before putting the cover on. That sets the main adjustment for the clutch lever side of the bike.
@Dafne0505
5 жыл бұрын
Yes, you are right, it's not on video.
@yomin3mg
3 жыл бұрын
Yea i cant do this job, i dont have a cat
@laurenceharvey6202
5 жыл бұрын
Top boss cat keeping an eye on everything 👀🤣👍😁🍻
@전정용-c3m
6 жыл бұрын
very cute cat! my bike's c109r(c1800r) 12years. U'r movie very important . Thank U.
@mahmoudhamed8285
Жыл бұрын
Hello Can you tell me how can I replacement boulevard M109R transfer case oil please??
@sandydenny4ever164
6 жыл бұрын
I see you've fitted a Cat alictic converter.
@WaitAMinute1989
2 жыл бұрын
That's the shop foreman.
@sumitkkanungo5423
2 жыл бұрын
when I start the my 2012 model m109r, the sound of rattling sound comes from the side of the clutch and as soon as you press the clutch lever, the sound stops what is the problem of the thing please help me
@algernoncoleman8461
2 жыл бұрын
Dude say something. I'm over here guessing like wtf are you doing
@barbatone3020
4 жыл бұрын
Bule kralju!!😉👍
@Dafne0505
4 жыл бұрын
pozdrav!
@adbyrd29
6 жыл бұрын
Why do people make vids without talking
@hellallnamesaretaken
5 жыл бұрын
davon byrd cause they dont know wtf they are doing lol.
@kelvinvandermerwe1575
3 жыл бұрын
Hi there, please could you share pictures of the pin mod, it would be greatly appreciated, even if its just a drawing. thanks and regards Kelvin
@xNOFEARx58
3 жыл бұрын
What part no. Has the clutch Cover gasket?
@agankachu09
7 жыл бұрын
Why would you replace the clutch? Did your rear tire slip/spin on start? Well, this is happening with my M109r. Can you please reply? Thanks!
@Dafne0505
7 жыл бұрын
yes After 60 000 km it started to slip more and more, not only when engaging from first, but at all gears... Clutch pack must be within factory spec. when measuring and changing. Everything must be replaced on this side. Also, watch clutch pin mode on 4:42 shaved by 2 mm, for better oil flow ( shave 2 mm deep on 120 degrees) ... Hope this is useful comment...
@davidjh5914
3 жыл бұрын
Bonjour comment vidanger la boite????
@emilstafstrom5401
3 жыл бұрын
Meanless,,,,bearings is differnt. Show us how to install THE bearings inside THE clutchcase
@mohamadchanty7717
3 жыл бұрын
I NOTICED THAT THE CLUTCH IS SMALL COMPARING TO A BIG ENGINE 1800 CC
@Madisonsemien9857
6 жыл бұрын
how did the ebc clutch kit hold up was thinking bout getting that kit was told not to that they would not hold up how has it held up so far
@Dafne0505
6 жыл бұрын
dear friend, so far so good. Not a single problem after 10K kilometers... This is OK for me...
@ericthered9655
4 жыл бұрын
No adjustment?
@zato6226
Жыл бұрын
Yes there is an adjustment. He left out the Half to 3/4 turn of the clutch pin
@Madisonsemien9857
5 жыл бұрын
How's the ebc clutches holding up
@Dafne0505
5 жыл бұрын
Still holding, no problems... I have to say that I am not riding as much as was. Anyway, I have about 10 000 km in last two years with EBC .
@vasyok148
2 жыл бұрын
35000км on EBC.
@oicduc
7 жыл бұрын
What year is bike?
@Dafne0505
7 жыл бұрын
This is 2007 model
@2563dicko
4 жыл бұрын
Did you need to drain the oil before taking the clutch cover off?
@Dafne0505
4 жыл бұрын
Of course, that`s imperative before taking any action. Thank you for asking.
@1993whitenoise
4 жыл бұрын
You actually don’t.
@mohamadchanty7717
3 жыл бұрын
THE MASTER QUESTION IS : THE BIKE IS NEW HOW COME THE CLUTCH IS FAULTY?
@Dafne0505
3 жыл бұрын
I have answered this before. The bike is from 2007.,
@mohamadchanty7717
3 жыл бұрын
WHAT WAS THE MILEAGE WHEN YOU REPLACED THE CLUTCH PLEASE
Пікірлер: 37