Coming along nicely. Looks like you will be starting it soon!!
@JMSpeedshop
Жыл бұрын
Engine is almost ready but i have to do the complete fuel system. And engine wiring. . But also the hydraulic system from the rear suspension . But i will get there soon
@RichardE3046
Жыл бұрын
En al dat werk gewoon even thuis in de garage, super!
@JMSpeedshop
Жыл бұрын
Dank je wel
@Lantan139
Жыл бұрын
This build is awesome too but I am still salivating over V12 w201
@mattmatt9971
3 ай бұрын
Beauty!🎉
@frighteg
4 күн бұрын
Did you machine the surface of the block?
@JMSpeedshop
4 күн бұрын
Yes . 0.17mm . Max is i think 0.3mm according to the manual . Only block . Heads should not be touched
@W210Garage
Ай бұрын
Is it difficult to install bearing bridge? Should i consider any trick? Also when i put the rocker arm in it's place, should all the hydraulic lifters move with the hand freely when the bolts aren't tightened? I just installed AMG Cams in my M113 and now i should bearing bridges.
@JMSpeedshop
Ай бұрын
I would remove all the hydraulic elements and at least drain them and installed them empty because of the different camshafts. So with new cams. You can get the right amount of oil in all the elements according to the new cam
@W210Garage
Ай бұрын
@@JMSpeedshop I need to know how to match the rockers on the engine, is there any trick. That’s why i asked.
@JMSpeedshop
Ай бұрын
What do you mean there are 3 types of rockers . Exhaust rockers. En 2 types on the intake van not go wrong
@W210Garage
Ай бұрын
@@JMSpeedshop Bearing Bridges. Just match the bolt holes and tighten with EPC/WIS spec ? I mean whole rocker arm, which goes on top of the Camshafts.
@JMSpeedshop
Ай бұрын
Yes follow the factory specs
@mantasjuodkojis1443
Жыл бұрын
Great job. Stock camshafts are good choice for your desired power? What ecu you are planning to use?
@JMSpeedshop
Жыл бұрын
Oem cams are.good for 5800rpms . It is a 5.0 v8 so i dont need high rpms to get to 700hp
@JMSpeedshop
Жыл бұрын
Ecu is going to be a Maxx ecu
@trevorgreenwald4043
9 ай бұрын
I have the m112. Do you know the torque pattern for the head bolts?
@red05srt
5 ай бұрын
What was your final torque spec for the cylinder heads with the studs
@JMSpeedshop
5 ай бұрын
On the studs i used it is 110nm
@thepio14343SWEG
Жыл бұрын
How long did this take/ cost you?
@slavimaster
Жыл бұрын
Hi, i have m113 without ZAS on my w220 and want to change the valve steam seals, it is necessary to change the camshaft bridge bolts to a new one.
@JMSpeedshop
Жыл бұрын
Every time the bearing bridge is removed you should renew the bolts. That is what the manual is saying
@YourFloridaLand
6 ай бұрын
When you put the sealant on, you cut the video, so I could not see if you put sealant on every mating surface, even around the cylinder walls? Please advise, thanks.
@JMSpeedshop
6 ай бұрын
Everywhere. But not around the cylinder bushings .
@videosourceonebusinessacco5438
4 ай бұрын
@@JMSpeedshop it did look like you put the sealant under the head gasket, but did you also put sealant over the top of the gasket, it looks like you did both sides, but wanted to check before I did mine this weekend. Mine is the m113k. Thanks.
@JMSpeedshop
4 ай бұрын
Hello. Yes that is correct . On block side and then headgasket on then some sealant on the headgasket. Then head on. But not around the cylinder bushings
@YourFloridaLand
4 ай бұрын
@JMSpeedshop thank you your videos have given me the courage to do this job...plus long ago, your video of the white CL55 was enough to make me get one...have had it, a s55, and now a SL55...they have been great..and man am I good at fixing ABC and PSE...lol
@JMSpeedshop
4 ай бұрын
Nice 😎
@robertrobbins837
Жыл бұрын
Do anyone know the proper name you called the place that you take the timing with on this video the to place that you sit on the cylinder head to make sure that the timing is set right I'm trying to order them
@JMSpeedshop
Жыл бұрын
i dont really know what you mean. i did not lock the timing
@robertrobbins837
Жыл бұрын
@@JMSpeedshop timing alignment plates
@rafag1194
11 ай бұрын
Can i reuse the camshaft sprocket bolt or need new everytime its out? Ty sir
@JMSpeedshop
11 ай бұрын
New
@azatzhansugirov162
Жыл бұрын
🙂👍
@LaurenJoe-mf1mh
Жыл бұрын
Blood
@Lantan139
Жыл бұрын
This build is awesome too but I am still salivating over V12 w201
Пікірлер: 39