Good video, I’m trying to take off back hubs on. a 48 Dodge B1D 1 ton Dually. Hope to complete it tomorrow. It’s not exactly the same, but very close.
@marlinhowze6164
3 жыл бұрын
Good job, gave me some basic answers on my '57 W300. Definitely a couple bad cylinders, but couldn't rule out a bearing or two. Thanks for puttin up the vid. Just have to break out the knuckle busters.
@jackcollins2344
4 жыл бұрын
I wish I had an answer to your question but I have never worked on a m37 so I will watch as you figure it out my friend.
@frankdavidson9675
2 жыл бұрын
those parts are 70 yrs old you can get parts at vintage power wagon in IOWA usa on line.
@frankdavidson9675
3 жыл бұрын
the bolts text to the lugs turn them clock wise in order it will push the drum off also on these stuck bolts i used freeze off in spray can spray it on a nut dont wait take the nut off it helps alot itworked ever time i tried it advansed auto carries it very good when you can not use heat those bolts are like pulling a fly wheel off
@frankdavidson9675
3 жыл бұрын
if you need parts ------VPW in UTAH has them
@frankdavidson9675
3 жыл бұрын
thats iowa not utah my error (old age )
@frankdavidson9675
3 жыл бұрын
oops the vpw in iowa not utah my error get on lin
@frankdavidson9675
3 жыл бұрын
i had to replace all my shoes and wheel cylinders -----vintage power wagon has all these parts if need them going from memory the rear and front brake cylinders are diff one is bigger watch that
@frankdavidson9675
3 жыл бұрын
when you take that spring off the shoes will fall off i used a large screw driver to remove that spring
@juanasanelli6831
4 жыл бұрын
No entiendo porque no aflojo las exentricas de ajuste de las zapatas y no los tornillos de anclaje como hizo Paso trabajo por demas
@seabeepatriot2258
4 жыл бұрын
I'm trying to adjust the brakes on a 1954 M37. Please help!!
@WatsonsWagons
4 жыл бұрын
Never done it yet still in tear down mode. Plenty of references online, forums, TMs. My first M37
@frankdavidson9675
3 жыл бұрын
a simple test to start if you have access to a dirt road go down the road in a hurry slam on brakes stop get out check slid marks all wheels all 4 should be about the same now to the adj ment if needed ther is abig nut on back side f each wheel you need some help with this have somr to pess brake pedal after you try to spin the wheel ofcorse you jack each wheel up turn that big nut till the the brake stop the wheel this is not bleeding the brakes this adj move the shoe closerththe drum wiout actualy touching i realize this is lengthy but you willneed bleed the brakes after this you should end with 3/4 of a pedal
@frankdavidson9675
3 жыл бұрын
there is a bolt on thr rear of the drum itslikea cam when you turn it you spread the bottom of the shoes prob- need jack it up so you can spin the tire have some press brake pedal for you while you make this adj. do all 4 wheels read my comment below this to test if you got it right
@frankdavidson9675
3 жыл бұрын
i bought m37 in 2011 still work on almost daily you get addicted have to tinker with it ( thats called ( tweeking ) lol list you ?????? i can help
@frankdavidson9675
3 жыл бұрын
do you have small bolts on face of drum run them in to remove drum
@jackcollins2344
3 жыл бұрын
Mike, are you still working on this project or what was the outcome, did you sell it or keep it? Just wondering.
@WatsonsWagons
3 жыл бұрын
Been on pause, sent daughter to college. Getting ready to ramp up work
@jackcollins2344
4 жыл бұрын
When you get finished with the m37 are you going to sell it or keep it? Just wondering
@WatsonsWagons
4 жыл бұрын
Jack Collins on the fence with that
@frankdavidson9675
3 жыл бұрын
you dont ever get finished been finishing mine 9 yrs love it i pulled the eng twice last time new rings
@frankdavidson9675
3 жыл бұрын
sorry i have two many vehicles now will be selling not trading im gona list it $ 14950.00 cash only no trades will lidst shortly
@frankdavidson9675
3 жыл бұрын
state your problem i will help you if i can also i know someone with vast knowledge of these m37s
@WatsonsWagons
3 жыл бұрын
Thanks, I’ll be jumping back into it soon
@jackcollins2344
4 жыл бұрын
I can't believe no one else has any interest in this project or if they do then I can't understand why you have no other comments.
@WatsonsWagons
4 жыл бұрын
Jack Collins most people watch and move on. I don’t get many “likes” and there is one guy out there who is waiting with baited breath to give me a thumbs down. Hahahahaha it’s all good
@thedudeabides7864
4 жыл бұрын
Jack Collins Probably because traction has not gained on this channel or series yet. I have an M37 1953, and I do searches for videos on the topic often. I only found this channel by chance through a Facebook video I happened to come across, otherwise it never came up before.
@frankdavidson9675
3 жыл бұрын
do you need help with anypart of it i igot mine in 2011 not many parts i havent takan off and fixed i found a way to covert dist to civ. very easy and cheap less than 50.00 new wire and 2.00 plugs fixed mine 7 yrs ago never had a .problem since 20.00 s[park plugs too much if yoy have tble with 24 voltage reg and gen you replace the whole mess for around 80.00 with 28 volt alt 1 wire to connect
@frankdavidson9675
Жыл бұрын
do not under stand you turniing that bottom bolt it just hold bottom of shoe in place its not tight the shoes are not holding the drum they do not touch thr drum unless you apply the brakes a lot of work for nothing
Пікірлер: 30