decent pulley... could hear it screaming here in Europe though, when you were broaching it : "gimme some oil man !!"
@MrSchoessow
9 жыл бұрын
Always enjoy your videos and learn something too!
@BasementShopGuy
9 жыл бұрын
Dennis Schoessow Thanks Dennis - thanks for the kind words too, I appreciate it ;)
@Herr_Bone
4 жыл бұрын
Yes, you can measure the outside diameter of the pulley with the micrometer screw and then press the key way by brutal force. That was quite amusing to look at. And you're absolutely right about using HSS. It is often the better tool for small machines, sharper, cleaner cut and much more universal. Nice video, even if I would have done it totally different. But that doesn't matter here....
@whitecaps775
9 жыл бұрын
Dang nice looking lathe there sir! Thanks.
@BasementShopGuy
9 жыл бұрын
whitecaps775 Thanks so much!
@MakinSumthinFromNuthin
7 жыл бұрын
Maybe my live center is a POS too, I have a horrendous time parting steel...dread it. LOL Pretty hefty lathe too...an Atlas 12 x 36 Commercial Underdrive Lathe. Excellent result on your pulley, nice job!
@redelk2974
4 жыл бұрын
Very nice. Inspiring...
@LeoTonius
7 жыл бұрын
Very nice lathe you have there!
@thomascoughran1374
9 жыл бұрын
Well done, sir!
@HardwayRanch
9 жыл бұрын
It was still funny even though the lag bolt held. Harbor Freight is you friend - just say'n... Thanks for the video.
@BasementShopGuy
9 жыл бұрын
HardwayRanch I think you're talking about their shop press right? If so, it's on the "next to get" list. Thanks for the kind words too, I appreciate it ;)
@PeterWMeek
9 жыл бұрын
You don't want white lithium grease for the center. What you actually are thinking of is white lead (nasty stuff, and rightly no longer available) - a traditional dead center lubricant. Keep using the Extreme Pressure lubricant until you get your live center fixed or replaced. You will damage your dead center and your workpiece using white (or any other color) lithium grease. It just isn't intended for heavy loads. Occasionally back off the center and work a bit more of the EP lube into the center hole. Wash your hands after using the EP #3, and don't smoke or eat with this lube on your hands. (From the MSDS) It has other additives besides plain petroleum distillates.
@BasementShopGuy
9 жыл бұрын
Peter W. Meek Good info - looks like the EP is good enough. Thanks for the info, very interesting!
@BedsitBob
7 жыл бұрын
I'm curious as to why you felt the need for a steady rest, while facing and centre drilling, but not while drilling and boring?
@turbocobra
9 жыл бұрын
very nice result on the pulley, bummer about the live center!
@BasementShopGuy
9 жыл бұрын
turbocobra Yeah, but with every setback, a lesson learned ;)
@MrShobar
9 жыл бұрын
Brad, you really should lubricate that broach. Fine work as always.
@BasementShopGuy
9 жыл бұрын
MrShobar I know - first time with broaching and it slipped my mind in my excitement to use it.
@PeterWMeek
9 жыл бұрын
Lube that broach with a good dark sulphurated cutting oil.
@BasementShopGuy
9 жыл бұрын
Peter W. Meek I know. My first time broaching and it slipped my mind in my excitement to use it. Next time and always thereafter for sure. Thanks Pete!
@fred.n.german5202
9 жыл бұрын
Hey Brad After broaching must have been a good work out. Good Job brother on the drive sheave. As for your center might need to change out the bearings to fix the deflection. Again Good Job
@BasementShopGuy
9 жыл бұрын
Fred German Hey Fred yeah, the bearings flex about .007 when I finally tested it. Thanks for the kind words too, I appreciate it ;)
@19441978
8 жыл бұрын
Good video Brad. Might want to try some lube on your next broach job.
@bx2200
8 жыл бұрын
Very nice job! So whatever happened wiith your Royal center? Did you send it back to Royal for evaluation/repair? -Chris
@ironhead65
6 жыл бұрын
New to all this, so maybe everyone else already knows. Why didn't you have to smooth the 30deg cuts? They looked rough in the video to me. Wouldnt you want them smooth so they do not prematurely ruin the belt? As I understand it, belts ride on the walks of a pulley. Thanks and great video!
@apollorobb
6 жыл бұрын
A little cutting oil on the Broach Goes a long way in ease of work and tool life.
@oldschool1993
5 жыл бұрын
Since you broke your pulley, what is turning the lathe? Also- why was it necessary to remove the motor pulley to change the belts?
@scottvincent1596
8 жыл бұрын
Good video! I'm glad to be be a new subscriber! Don't forget to lube the broach! LOL! Just joking about the lube! I think you've already been told enough! Lol
@BasementShopGuy
8 жыл бұрын
+scott vincent I know - I too cringe when I watch it. Over excitement really got the best of me, that day, LOL
@sryth1
8 жыл бұрын
I might be missing something, but it looks like you squared your parting tool to the uncut part of the stock?
@AmateurRedneckWorkshop
9 жыл бұрын
Hey Brad isn't this the second time you uploaded this video? What happened?
@BasementShopGuy
9 жыл бұрын
cerberus Was playing with the video editor and it got messed up (and deleted), so I reloaded it
@ibrich42222
9 жыл бұрын
Brad, I liked your video. I usually use cutting oil when broaching thinking it might help no matter how little.
@BasementShopGuy
9 жыл бұрын
Ron Rich Yeah, my first time broaching. Completely slipped me... LOL
@skeeterweazel
9 жыл бұрын
Thx for the video. One little suggestion: i believe you're not using your snap gauge correctly. I wanted to post a link to a video but it won't let me. Please search for "how to use a telescoping gauge".
@BasementShopGuy
7 жыл бұрын
You slightly tilt it, expand it, then rock it out of the hole which will push the plunger back in at the exact diameter of the hole. It might have glitched with the lack of room and possibly rushing.
@garthn2561
9 жыл бұрын
Dialling in to a thousandth is an absolute waste of time if you are still turning the outside down. The only benefit is to avoid vibration - a thousandth or two does not cause that
@BasementShopGuy
9 жыл бұрын
+Arduous Andotherous Dialing in? Meaning with the chuck?
@jackminer2783
8 жыл бұрын
+BasementShopGuy yea what was the reasoning behind doing all that initially zeroing if you hadn't turned anything yet?
@rickl.orchids
9 жыл бұрын
was even better 2nd time around......
@BasementShopGuy
9 жыл бұрын
Rick L Thanks buddy!!
@paulgreenlee190
4 жыл бұрын
I've asked before if you could possibly give some advice, I have a 13" South Bend. The front bearing is set good but the rear bearing gets hot. Right now it's showing .006 when I apply 50 lbs. of lift. If I remove .002 on each side you can't turn it by hand and there is no way it will turn freely like yours by hand. It was damaged like this before I bought it. Did you do anything different when you put your bearings and caps on? Old Iron Lover gave me some advice to remove .001 from one side at a time to see if I could get it down to the clearance of .0007 to .0015. I have to use the chuck key in order to move it. Any advice at all?
@BasementShopGuy
4 жыл бұрын
The rear right get hot due to the back gears transferring heat to the spindle. Or it's not getting proper oil. It's hard to stay without being there. Mic the shims to ensure you're removing the right amount because they're laminated.
@paulgreenlee190
4 жыл бұрын
No your right, hard to make a call not seeing it up close. I had to pull the bearings and capillary oilier out, they were shot and went back with new. The rear is a monster, damage from the previous owner and damage from the expander pulling through the bearing. I filed and reshaped as much as I could and I have to be careful not to break the small screws pulling the expander up. This spindle has never spun easy at all. Maybe the spindle is not true but how would I check it in the lathe? I'm worn out trying to find a fix for this lathe. Thank you for at least taking the time to respond. I have learned a lot watching your channel. You don't have to bother with the old stuff any more with your new lathe in your shop. That was a great move in the long run.
@medvedmedvedoff4803
7 жыл бұрын
Chatter... A lot of chatter. I mean dead spindle sleeves or bearings is a reason of chatter. Thank you for video! Subscribe and like.
@stewartfrye
4 жыл бұрын
thousandths on a pulley, really final measurement WHY
@Logicinfact
5 жыл бұрын
Chatter is from too much surface speed.
@Reese_Asher
8 жыл бұрын
*17:45**, What RPM were you running?*
@BasementShopGuy
8 жыл бұрын
+Reese Asher Around 80-90.
@Reese_Asher
8 жыл бұрын
*GEEZ that low*
@BasementShopGuy
9 жыл бұрын
Was messing around with the video editor. Video got messed up a little and saved as a new video.
@jimstone2669
9 жыл бұрын
OIL OIL that broach
@BasementShopGuy
9 жыл бұрын
jim stone I know, lol... In my excitement to use it for the first time, it slipped my mind ;)
@BillyDocWalker
5 жыл бұрын
Put some oil on it DA
@BasementShopGuy
5 жыл бұрын
William Walker oil isn’t needed with those light Cuts. But you know because you machine right, dumb ass?
@MadHatter123456
7 жыл бұрын
All this trueing and indicating for nothing. Just mount it in the chuck, center-drill (no need for a facing-cut) and jam the live-center into it. No need for anything more than that since you're machining all the surfaces anyway...
@BasementShopGuy
7 жыл бұрын
Well, no... My 3-jaw wasn't big enough to support this piece, so I needed to use the 4J. And to machine it safe, without introducing a whole mess of vibration, etc - you dial it in. It was also some practice for the 4-jaw competition at the 1st Bash. And you'll notice I dialed it within .002 and mentioned that it was good enough, being that it'd be turned down.
@shawneliason790
6 жыл бұрын
you should shave your eyebrows off as well..
@jmanatee
9 жыл бұрын
Bummer I was hoping for a new vid....
@BasementShopGuy
9 жыл бұрын
***** More to come, for sure! Thanks for the kind words too, I appreciate it ;)
@KnolltopFarms
9 жыл бұрын
Congratulations, nice handiwork on that daul-pulley! I know I I'm ever to upgrade to a 2hp that I will want to not only have a beefier set up, but will also attempt dual drive and driven pulleys for supreme power transmission. That is if you think my flat belt could transmit the load to my cone-pulleys? BTW, I have a new pair of videos showing my current set up from parts I had here in the shop...excepting of course my drum switch that went in flawlessly the very 1st time[Proudness!]. I'll be wiring it with armored 12/3 flex-conduit and with a possibly slightly different arrangement when I get some dough, and also will be installing an endless flat-belt like you glued up. Things are slowly coming together :) Thanks for sharing this nice show, and I'm sorry about your triple bearing Royal center, that is a BUMMER! Doing my darndest to come to SoCal to meet you all, Aloha...Chuck
@BasementShopGuy
9 жыл бұрын
Knolltop Farms Thanks Chuck! Yes, I DO think your machine will transfer the power with a rubber-backed belt. My machine is supposed to have a 2hp motor and leather belt. It (has) a 1hp, so someone must have swapped it out. However, I'm planning on getting a 3hp to better transmit power to my carbide inserts. Thanks for the kind words too, I appreciate it ;)
@fabiankirschner9982
6 жыл бұрын
i hope i will never ever have to see such bad turning amen
Пікірлер: 65