amazing job! I've been following your progress for quite some time now.
@ThisDesignedThat
3 жыл бұрын
Thank you very much!
@JohnJones-oy3md
3 жыл бұрын
3:30 - Me: How on earth could one possibly align those two parts in a press so they line up properly? You: Hold my beer. LOL
@lxnyn
3 жыл бұрын
Lol
@ThisDesignedThat
3 жыл бұрын
😁
@stevenschroder789
4 ай бұрын
Could you share what epoxy you are using? Thanks
@TheHadMatters
9 ай бұрын
What's the benefit of going in two steps here, instead of just making the negative in metal? Is the metal unsuitable for the press?
@ThisDesignedThat
9 ай бұрын
It's very difficult to get the tolerances tight enough on a low cost CNC machine that will produce an accurate positive and negative
@RTCDigitalS
3 ай бұрын
Hey bro! Amazing video ive learned alot from you. The other foil stamping video with resin pront was great too! What is the name of this machine called ? Ive tried to find it for so long, tried "foil press" without luck. Thank you!
@ThisDesignedThat
3 ай бұрын
Hot Foil Platen Press 👍
@anantnarayandash4629
Жыл бұрын
Great tutorial. But what if someone wanted am intricate artwork to be embossed on paper ? Will the same process ?
@ThisDesignedThat
Жыл бұрын
generally, yes, it is the same process
@ewanpowell9448
2 жыл бұрын
Are you able to share what kind of CNC setup you're using here to cut the aluminium? (assuming it's aluminium and not steel!)
@ThisDesignedThat
2 жыл бұрын
Take a look at my CNC playlist, should cover most things - kzitem.info/door/PLThNZEmqjs3kP6h8Ynm7TI6QWgbg4NCqK
@donochetti2177
Жыл бұрын
Hi great video, I am about to make one on the cnc but was wondering why not cut out the male part out of alu as well? Cheers!
@ThisDesignedThat
Жыл бұрын
My machine tolerances are not accurate enough to create the male and female dies. I would say most hobby machines wouldn't be able to do it, especially intricate shapes like letters
@donochetti2177
Жыл бұрын
@@ThisDesignedThat Ah ok I have pretty good tolerances on mine so will give it a go. I really appreciate the reply thank you again for the great video !!!!
@jmerilo
3 жыл бұрын
Would it be possible to use that clamping jig for die cutting small boxes?
@ThisDesignedThat
3 жыл бұрын
Im not sure you could make something sharp enough with this method to cut card. Usually you lay a blade in a groove to make the die cutter
@bavllysamy3321
2 жыл бұрын
Hi Paul, Really, it's fascinating Could you please advise for these three questions? 1- How much time spent to hardened the epoxy? @ 2:20 2- Does the heat will affect to expedite the process? 3- And there is any side effect on the surface of the counter-part or its composition due to use of heat? Thanks
@ThisDesignedThat
2 жыл бұрын
1 - I leave it overnight but your epoxy brand will give you a specific cure time, its usually 6-24 hours 2 - Heat will speed up the epoxy cure time I believe 3 - Not sure I understand your question
@bavllysamy3321
2 жыл бұрын
@@ThisDesignedThat I would like to thank you for your interest & respected reply And if you don't mind to send your email, I'll be grateful to you Because I already sent you an email on that one that's exist in description But may doesn't work
@JohnJones-oy3md
3 жыл бұрын
Paul, quick question - how hard is the polyurethane used for the counter-die? Is it in the rubbery Shore A range or a more rigid Shore D? Thanks.
@ThisDesignedThat
3 жыл бұрын
Hi John. Its polyurethane resin with a shore D rating of 72. Its incredibly tough. No reason why you couldn't use cheaper epoxy or polyester resin to do this though.
@alvint4944
2 жыл бұрын
Hi! What was sprayed on the metal plate? Also, what type of epoxy was used?
@ThisDesignedThat
2 жыл бұрын
Mould release spray, link is in description I used polyurethane resin, but epoxy or polyester resin will also work fine
@alvint4944
2 жыл бұрын
@@ThisDesignedThat thanks for replying, will check out the mould release spray. Will this work on small details or small text?
@ThisDesignedThat
2 жыл бұрын
@@alvint4944 Yes it will work very well with small text, get a good quality mould release spray, it really helps!
@alvint4944
2 жыл бұрын
@@ThisDesignedThat thanks for the tip!
@joelwhite55
2 жыл бұрын
Hi Paul, wondering if you would be able provide your email, I’d be interested in having a die made to emboss our company presentation folders. Thanks, Joel
@ThisDesignedThat
2 жыл бұрын
Hi Joel, you can find my contact info on the about page - kzitem.infoabout
Пікірлер: 33