could i possibly order just a neck like this? I have a bolt on neck guitar and would love this style more than mine. How much would it cost? Do you also pain and stain them?
@karelmensik2698
7 жыл бұрын
Did you ever have a truss rod rattle? Twice I put nothing in the channel to prevent rattle, twice it did rattle. I do very tight channel. Yours seems to be loose enough to cause rattle. Last time I covered the whole 2-way truss rod with another heat shrink tubing, wich also prevents it from the glue.
@HighlineGuitars
7 жыл бұрын
Never had rattle.
@Eumldeuml1234
8 жыл бұрын
What's the size of the bit on the CNC machine? Since the slots for the frets should be around 0.6mm wide I'm wondering if there is a router bit that's so small. Besides that you're doing an awesome job! Going to start my own build soon and your videos help a lot :)
@HighlineGuitars
8 жыл бұрын
It's a .023" diameter, solid carbide, 2 flute, spiral upcut end mill. And they are available in much smaller sizes.
@cdavis6406
Жыл бұрын
What size fret caul do you use since the radius increases with the scale offset?
@russellscott1151
5 жыл бұрын
Like the head design. Seen something similar on another manufacturers site but they also built in a aluminium laminated layer to prevent the head twisting/breaking. Have you had any issues with it doing that and how long have you made that design for? Many thank.
@HighlineGuitars
5 жыл бұрын
No issues that I am aware of, however, I no longer make that design. It's too dated IMO.
@viociarnau1670
5 жыл бұрын
Where did you get the CNC machine from? Also how much did you pay for it? Is that Dewalt router you’re using in it?...
@07LUTE70
8 жыл бұрын
Is that belt sander from harbor freight it's green . I think it's just like mine . What grit is the paper your using the 80 or 60 grit?
@edadpops1709
7 жыл бұрын
Chris did you have your 12 th fret be the perpendicular fret! For 7 string what was the width aat the 1st fret?
@tyler_bt3326
7 жыл бұрын
When working out the fan ( say you're using the 7th fret as the midpoint for the multiscale frets) is it as simple as marking out the top and bottom scales then lining up everything in between?
@HighlineGuitars
7 жыл бұрын
I use this online calculator to layout the fretboard for multiscale: www.ekips.org/tools/guitar/fretfind2d/ Under "scale length," select "multiple." Under "perpendicular fret distance" click the question mark and enter the number that corresponds with the fret you want to use as the midpoint.
@russellscott1151
5 жыл бұрын
How do you make your home made radius sanding blocks accurately for doing the fretboards? They are relatively expensive to buy. Thank
@HighlineGuitars
5 жыл бұрын
I have a CNC machine. I'm about to use it to make a 30" long, 12" radius sanding block.
@russellscott5823
5 жыл бұрын
Yes, I suddenly realised that’s what you probably did. Thanks.
@martinreyes7730
5 жыл бұрын
How do you know where to pit the frets in and the slant and the straight fret an all of that?
@HighlineGuitars
5 жыл бұрын
www.ekips.org/tools/guitar/fretfind2d/
@alisaleh9102
8 жыл бұрын
The question is how did you specify the frets positions? Would you please reply.
@HighlineGuitars
8 жыл бұрын
I use this web site www.ekips.org/tools/guitar/fretfind2d/
@alisaleh9102
8 жыл бұрын
Highline Guitars Thanks a lot this should help
@adampleasance9567
7 жыл бұрын
did you radius the fretwire perpendicular to the fretboard? or did you need to take into account the additionall radius added by the fan?
@HighlineGuitars
7 жыл бұрын
I radius perpendicular. Trying to take into account the fan of the frets would be an exercise in unnecessary futility which might lead to insanity and death.
@adampleasance9567
7 жыл бұрын
Highline Guitars thanks for the reply! I suspected that's probably how you would do it :)
@rockhopper8160
Жыл бұрын
@@HighlineGuitars Thanks for answering this question here, I’ve been looking for the answer to this everywhere
@senseibear2436
Жыл бұрын
... Casually uses CNC machine...
@CaffeinatedAFK
7 жыл бұрын
how can i download the file from FretFind2D?, i cant find the save button or something like that.
@HighlineGuitars
7 жыл бұрын
Try a different browser. I use Chrome. The save buttons should be on the right side of the page.
@CaffeinatedAFK
7 жыл бұрын
Highline Guitars Thank you so much! it worked, i really appreciate it!
Пікірлер: 30