Nice job. The glow plug power is actually programmable. It's set to 85 watts by default, but many have said it will run fine at 35 watts, with the benefit of prolonging the plug's lifespan. In a limited mAh setup like yours, you'd probably benefit from playing with this setting. It's the "pf" in the settings menu. 1=35w, 2=40w, 3=45w, 4=80w, 5=85w, 6=90w.
@JoshsJettas
8 ай бұрын
That’s interesting I wasn’t aware it’s changeable. Although I’m afraid of cold combustion temps causing sooting with the thermostat set up, my thought is quicker it’s hot the better?
@WaffleStaffel
8 ай бұрын
@@JoshsJettas You're right about that, and the glow plug also runs on shutdown I believe to keep the little screen clean, but I think 45w would still make it glow almost white. I guess it's something you'd have to test by pulling the screen out after a few burns.
@chadnelson8752
6 ай бұрын
This video was awesome. I'm not knowledgeable enough to have figured out how to do it on my own, but I know enough to follow your instructions. I use the heater to heat my chicken coop and this solution is going to save me a ton of money and headache!
@JoshsJettas
6 ай бұрын
It works awesome, another option which is easier yet is the Bureck thermostat. It just copies the remote signal and does it’s thing, I switched to that as I needed these relays for something else
@chadnelson8752
6 ай бұрын
Yeah I looked into that one first, but it wasn't compatible with my remote.
@JoshsJettas
6 ай бұрын
Then this is a great alternative. It does need to be baby sat to a certain degree but it works well
@RiDankulous
5 ай бұрын
Smart ideas like this make the world a better place. Thanks!
@philliplopez8745
23 күн бұрын
Set mine up , there are a few quirks , but it is so nice having the heater cycle , and I am certain it will save gallons .
@JoshsJettas
4 күн бұрын
Yeah it’s by no means perfect but it definitely saves fuel
@liamhenderson3753
8 ай бұрын
Great video. This is exactly what I need. You make it seem doable. Much appreciated.
@JoshsJettas
8 ай бұрын
If I was to do it again I’d hook it to the remote and wire to the separate on/off switch
@TimShelnut
9 ай бұрын
Pretty cool setup if I was to do this which I use in my jetta wagon by the way. I would use the remote, I haven't gone down this rabbit hole yet but did want to automate this heater somewhat. Maybe holiday project if I finish some of the others. Jetta tdi needs so maintenance first.
@JoshsJettas
9 ай бұрын
There’s always something to do, im just working away at deferred maintenance on my Touareg. I’m really liking the bureck remote to keep it at a set temp. The heater itself does have a timer so you can get it to kick on at a certain time but people say sometimes the clock gains 5 minutes a day so that kinda throws a wrench in that, whereas the bureck keeps time and has up to 4 timers. How do you plan on mounting it in the wagon?
@TimShelnut
9 ай бұрын
@@JoshsJettas yes sir always something. Touaregs are nice thought about getting one. I have basically took one installed it in the typical harbor freight case and run it into the window. I'd show photo but can't post it here. I used instalation board in window to pass through the heat.
@richiefekecs
10 ай бұрын
looking forward to the Bureck review!
@migikuburic4237
5 ай бұрын
Great ideas ,thank you for help🙏
@jasonruggles1706
Күн бұрын
i purchased the hcalory ss2 diesel air heater. the controller has auto on and auto off. also can set it to Fahrenheit. So you just set a temp. The heater goes on and then ramps down once its up to temp. then it shuts off. then back on.
@Hartloop100
8 ай бұрын
Nice one Good Clip finely easy way to hack this dam heater at last i can rig my one to do the same keep it up making videos
@j.s.t.medicalltd6199
4 ай бұрын
Hey, just put this in my camper. Your instructions were fantastic! I am having this problem with it not switching as it’s technically holding the on button on and prefers a press or and on/off. Do you know of a solution? ☺️
@JoshsJettas
4 ай бұрын
Im prettt sure someone else had posted that issue here too, there must be different variations of this display some are okay with a constant on/off and some aren’t. A timer relay wired in should take care of it
@philliplopez8745
23 күн бұрын
All you need to do is set both stats to the same temperature.
@marcomarchi2745
8 ай бұрын
I don't understand how you can apply a momentary impulse...the relay stays on and simulate a long button press..in this way the heater enter in some option menu...
@JoshsJettas
8 ай бұрын
So this heater is now 2 years old and they seem to update/change controllers frequently. Mine I can hold as long as I want, there’s a seperate button for menu. That being said there was another recent comment that they just bought a vevor and it does what your describing. I timer relay will be needed in your case.
@sunroameroverland
8 ай бұрын
I didn’t see where you mentioned where to get these two parts needed
@JoshsJettas
8 ай бұрын
W1209 on amazon, fairly inexpensive and some can come with a case which I regret not getting.
@jimbo5728
8 ай бұрын
Problem with the two devices is if you get out of sync as you said. That's kind of a big problem... Another youtuber had a similar scheme, with the same problem.
@JoshsJettas
8 ай бұрын
I ran it for a month and had 3 instances where it messed up if I remember right, and once was self inflicted from running the generator. I think ideally it should be wired separately to the remote on and off switches or use a timer relay inline, issue with that is then you need to adjust your time to make sure your heated space has cooled down/warmed up enough
@letzgow6110
18 күн бұрын
Do you have a follow up for the remote control
@JoshsJettas
4 күн бұрын
Ill probably do a final one with everything working this fall, worked well all last winter kzitem.info/news/bejne/wKZ_uJiZjJqYrI4feature=shared
@mickgatz214
9 ай бұрын
Hey Josh, great video. That concept u used is what I want to do with my LifeP4 batteries.. eg/ turn off @ 13.3 or .2, then turn off @12.2 to or whatever the favourable min voltage is. Is there a PLC about that can achieve this? Power Supply 13.8v 35A. Cheers!
@alexzbarazky3038
8 ай бұрын
After you trying to implement a low volt disconnect? Victron battery protect would do that. Or a voltage triggered relay opening an isolator relay.
@d.j.robinson9424
9 ай бұрын
Wow, nice job. This was great showing the details.. is it possible to to run a standard 12v thermostat inline with your control board with a few diodes?? The controller, I thought, allows the glow plug to cool down in programming, with the fan running ...?? Anyways, an excellent video, I need something like this config for my chicken coop; I don't need it to run in the daytime, only at night. Any geeky ideas ?? 👍👍💛🍻🐓
@JoshsJettas
8 ай бұрын
As in a a thermostat that cuts power to the display? That’s not what you want, Since this is wired to the on/off it goes through the required pre/post glow plug and fan cycles as required. I made a second video using the Bureck cd thermostat, extremely simple to set up and use and saves wiring.
@d.j.robinson9424
8 ай бұрын
@@JoshsJettas I just watched it 👍
@CS-uc2oh
7 ай бұрын
It doesn't make sense to use a thermostat on this kind of heater especially if it's being used in a vehicle. There would be a waste of energy starting it up again once the inside temp of the rig drops too low (and it will).
@JoshsJettas
6 ай бұрын
Waste of energy? Like battery energy? It’s the same as your house thermostat, you don’t just let your furnace run 24/7 and crack a window when it’s too hot do you? This set up works awesome, I can get 10 days out of a tank now vs just running the heater 24/7 and only getting 2.5 days.
@WiLLiAMOnline
9 ай бұрын
Fantastic video.. thankyou! very useful and a great hack to get these diesel heaters running a bit more like we all expect ;) subbed! Merry Christmas if you celebrate it 👏🏻
@JoshsJettas
9 ай бұрын
It's much needed, thank you Merry Christmas to you as well. I also did a video with the Bureck thermostat which is working flawless, i did have a few minor issues with this set up.
@dogdazetravellergarrett1367
Ай бұрын
Good video...... Not sure if the extra control of fine tuning the differential temperature is necessary for most applications of use. Very clever, well thought out project done..... Nice job 😎👍
@olegmart2251
10 ай бұрын
Yes I got Bureck and it is game changer
@bureckllc
10 ай бұрын
So glad to hear you like it!
@eda7875
2 ай бұрын
This is gold
@h4z4rd42
8 ай бұрын
This setup definitely needs an inching function, to fire your relays only for a few seconds, to avoid that situation like if you hold the power button too long. BUT, it gave me an idea *how* to use Sonoff smart relays to switch the heater even remotely, so thanks a lot.
@JoshsJettas
8 ай бұрын
Yes it could definitely be improved, another thought was wire separately to the remote. I bought these for a different project so I was just making due with what I had
@h4z4rd42
8 ай бұрын
@@JoshsJettas just bought a vevor heater myself. Funny, this one turns on/off at a short press and enters the menu at a long press. So remote access achieved easily by a sonoff relay.
@j.s.t.medicalltd6199
4 ай бұрын
Hi, I have done this set up and am having this problem with it not switching as it’s technically holding the on button on. Do you know of a solution? ☺️
@patrickday4206
7 ай бұрын
I did exactly the same thing just once in a blue moon doesn't shut off but i had to do a delay switch so it stays on for a couple of seconds
@JoshsJettas
7 ай бұрын
Yes that’s exactly what this needed.
@syncrosimon
7 ай бұрын
Great idea and explanation 🏴🏴
@navigatingthedestination
9 ай бұрын
My Chinese diesel heater doesn't have a remote. Is this my only option unless I change the controler and motherboard. my control panel looks the same as yours. I like the amount of control you have with your system. Oh, could you connect a house thermostat the same way as yours. I'd like to do this modification for in my van. Thanks for sharing 👍
@rudbeckia885
8 ай бұрын
My switch won't turn on fuse good power to fuse good
@djohnsto2
8 ай бұрын
This is interesting - What I want to do is power off the unit safely when my mains-based 12V power has an outage - It'll still run on battery for a while but eventually it'll suffer a hard stop when the battery is drained. I had this happen but I was standing right there and saw it, so I gave mouth-to-mouth to the air intake to cool the combustion chamber, and quickly alligator-clipped on a secondary 12V source and powered it on, then off and it did its cooldown properly. So it didn't get damaged. I'd rather not have to give it another BJ.
@JoshsJettas
8 ай бұрын
I assume you want a relay to shut the heater off at say 12v instead of the battery killing it at 11.5v? Are you using a cordless tool battery to power it? I have no experience with it but try a xh-m609.
@timnelson5037
7 ай бұрын
Just curious, if these have a c (cold ) and an hour (hot) setting , just wonder if you could just use one instead of 2 ?? Not trying to be negative, just wondering...
@JoshsJettas
7 ай бұрын
Not that I could see, it was one or the other
@tbrcwings5898
9 ай бұрын
Great video Josh. Saved me a ton of head scratching to figure out how to thermostatically control the heater I am just about to install.
@JoshsJettas
9 ай бұрын
This worked awesome for the month-ish i used it, if you want a flawless system look in Bureck CD thermostat
@tbrcwings5898
9 ай бұрын
@@JoshsJettas Yeah I discovered them a while back. A bit pricey for what I assume is a arduino based cpu running simple code. Bit of a electronics nerd myself and enjoy building stuff. Not sure if the code Aaron runs is open source or not. Besides that, the particular heater I bought is not compatible with his rig. Red remote. :(
@JoshsJettas
9 ай бұрын
@tbrcwings5898 yeah this set up is simple and cheap, and as you said it’s universal. I’m not much into electronics but I’m good at researching solutions to my problems, I had planned on going with arduino but that learning curve was pretty steep. Maybe one day I’ll find some time to play around with coding.
@Danguy351
10 ай бұрын
Hey Josh, just curious what the out the door cost of the Bureck ended up being after exchange, duties, shipping to Canada, and all that fun stuff? Did you opt for the battery model or just the usb powered?
@JoshsJettas
10 ай бұрын
I’m planning on posting a video tonight on it, I went with the corded version. $50usd plus $5usd for shipping came out to $78 cad. Shipped with usps/Canada post and didn’t have any duties.
@Danguy351
10 ай бұрын
@@JoshsJettas that's awesome--I'm going to go ahead and order one up. Looking forward to the video
@gordonseykora8137
9 ай бұрын
Use a Bureck.
@JoshsJettas
9 ай бұрын
This was a temporary set up while waiting for the bureck, apparently mine had some issues at the border
Пікірлер: 67