Thank you so much for the video and the compiled code. I hope everyone can appreciate the time it takes to out that together. This is exactly what I have been trying to do with my Growatt inverter.
@emiller233
2 жыл бұрын
Any luck getting yours to work
@jwsolarusa
3 жыл бұрын
Fantastic job well done brother. You are really good at working with little and tiny space. Finally, you are awesome with electronics. Please have a wonderful day.
@edenmadden3240
3 жыл бұрын
Pro tip: watch movies at flixzone. Been using them for watching a lot of movies lately.
@kalebroberto2363
3 жыл бұрын
@Eden Madden Yea, I have been using Flixzone for since november myself :)
@halisdabai
3 жыл бұрын
you really a genius pls i want you to train me more. thank you
@ThanosSustainable
3 жыл бұрын
Would really appreciate it if you could make some content of how MQTT works and why.
@DIYTechRepairs
3 жыл бұрын
Thanks for watching. I could but there are so MANY really good videos about it out there :) I link some for you. Channels that i follow on daily basis: kzitem.info/news/bejne/r6CBsWmXm2JefqA kzitem.info/news/bejne/oql6rnl6m6t9mZw kzitem.info/news/bejne/x62Ym413iayBeqA Those 3 are some of many that explains it. But shortly MQTT is a way of easily sending messages between devices/clients :)
@pandaygaming1646
3 жыл бұрын
thank you for this video. i was able to used it to my Xtra Power Inverter. the inverter is working on PCM but have to use the PIP code to publish inverter information. Hopefully there is a tutorial on how to aggregate or sum those information daily, monthly etc. :)
@wobbleszo
3 жыл бұрын
Very cool! Thanks for sharing your projects with us!!
@TheKilowattChallenge
3 жыл бұрын
Awesome video Daniel. I might try this when I'm up and running
@SignedForFun
3 жыл бұрын
So Mpp Solar HV2-5048 is using P18 protocol. I had to code from scratch not being a programmer, it took a while. I got this working and setting commands work as well. Thank you, for the idea
@jenschristensen8363
2 жыл бұрын
Hi how did you change the protocol?
@SignedForFun
2 жыл бұрын
@@jenschristensen8363 i don't understand the question well - i have not changed the protocol. I have written my own code for d1 mini using the idea from this video. Because that particular protocol (P18) my inverter is using was not available in the code written by the author of this video
@makeitsimple2306
3 жыл бұрын
Grateful for your work in this video 😍😍 Just how the mqtt send data this is so complicated for me😅
@raytry69
10 ай бұрын
1:32 You could make a separate picture of the back side and include that pic later on the video.
@kARTechnology
3 жыл бұрын
I've done this for 2 inverters and working flawless and can set parameters remotely too. Coded my own.
@bobkammoun8375
2 жыл бұрын
Hi could you please give any help about this project.
@kARTechnology
2 жыл бұрын
@@bobkammoun8375 are you trying to build from scratch
@bobkammoun8375
2 жыл бұрын
Yes dear i have already programmed the nodemcu and connected it to rs232 max db and i am getting data from info, wifi and up time but no data from status
@kARTechnology
2 жыл бұрын
@@bobkammoun8375 check the checksum...
@bobkammoun8375
2 жыл бұрын
@@kARTechnology im sorry i didnt get your point where should i check it
@kevinshettle8965
3 жыл бұрын
what is the banging in the background.......the wife chopping onions lol
@DIYTechRepairs
3 жыл бұрын
My kid :) they are Always with me in the garage
@diginomad6016
3 жыл бұрын
Great work. Hope you are doing good
@danfitzpatrick4112
3 жыл бұрын
Awesome! I am very interested in having this setup for my new mppsolar Lv6548 inverters. I am using two of them in split phase setup
@DIYTechRepairs
3 жыл бұрын
Go for it!
@libenasukro
4 ай бұрын
Where would i go in those git hub files to change the serial port command set? I have a Steca, but it uses many of the same codes, just for different functions. I thought I would see at least outlandish values, but I get 0 for every field. I even reversed the tx and rx just in case. The same pinout on a usb to serial works fine, so it's not the cable...I fear it's the operator. There are values in Wifi topic, but every other topic is blank. I tried MPI and PIP. No change.
@mzainmunawwer780
11 ай бұрын
Dear sir i M stuck at both lights on ( red and green) rs232 to ttl converter not connecting to inverter. I have checked all the connections. Everything is ok but not connecting to inverter. Voltronic Power Axpert VM3 inverter.
@EbanQHanna
4 ай бұрын
I want purchase 4 of those devices. Please advise how we can make this transaction.
@SignedForFun
3 жыл бұрын
Hi again, so my inverter Mpp Solar HV2-5048 uses a different protocol. I am interested to add a code to your software to make it work.
@jihadkhorfan
2 жыл бұрын
Great work .. is the esp hosting the webpage you showed in the beginning of the video
@Terminator-hy8wv
Жыл бұрын
hi. I use the software "SolarPower v.1.16" If i connect the the computer over the usb port to the inverter, nothing happens. i cant get acces to the inverter. Do you have a hint for me to get a connection started?
@BlueSky-cy5nw
Жыл бұрын
Hi, thanks for the video. Just wondering if this will work with Voltronic inverters. Also would be cool to take this project a bit further and build an Inverter dashboard on Home Assistant.
@SignedForFun
3 жыл бұрын
Hi. Excellent work - a big thumbs up from me! Will this work with MPPSolar hybrid HV2-5048?
@user-es9xi8fp4q
Жыл бұрын
Hi brother Is there any chance to learn me how to connect my inverter (must 3kw) to the mobile via wi fi or Lan cable
@mariamajallow6304
2 жыл бұрын
Am a student an new to the system am really impress with the work i will love to be guide if possible am from gambia
@talharafique8913
2 жыл бұрын
what a really generous person. you made it very cheap but in market these devices cost $70+ . Little question, can our WatchPower software of inverter detect this in-network so eighter showing results in MQTTserver, we can see results in actual inverter software?
@DIYTechRepairs
2 жыл бұрын
No you cant use both at same Time. Its either or.
@talharafique8913
2 жыл бұрын
@@DIYTechRepairs i mean using this device, we connect to our software instead of MQTT server ? is that possible. in that way we can chnage settings for our inverter, as you also doing this before making this device. with wire and PC and inverter software. is that possible with this wifi device ?
@parstal4972
3 жыл бұрын
👍 Imponerande, hokus pokus för mig !
@robertdelczeg8834
Жыл бұрын
hello, do you know how to set phase equalization for this device?
@antonio.stefanelli
Жыл бұрын
Thanks a lot for the content! But is possible to send data to emoncms ? Like solpiplog but for esp and not only for raspberry.
@DIYTechRepairs
Жыл бұрын
Most likely. This only does mqtt so just convert it i guess.
@Mr123trade
Жыл бұрын
Do these work with the MPP Solar inverters? 5048PIP?
@virginiaperez8971
2 жыл бұрын
genial gracias
@guywhoknows
Жыл бұрын
I'm looking for this to work with a growatt min. Inverter. But I was not looking for mqqt, but gagues. I was looking at the code for the ads1115 which is fine but had trouble shifting the data over. That uses JSON but for some reason the strong format (which I had to change) wouldn't work (getreadings) It was to monitor solar strings individually. It would be easy to port to battery and inverter output. But data exchange.. I2c....
@Maaz_Gaming29
Жыл бұрын
kindly help me out is it work for me thankyou really inspired with your work
@roadeycarl
3 жыл бұрын
I would be happy to help test PIP if this is a project you are still working on? Thanks for all your hard work.
@DIYTechRepairs
3 жыл бұрын
IF you have a proper pip modell and the hardware/ some knowledge in programming sure! To debug you should be able to hook Up another Serial port to it. Then send me an email. Info on about page :)
@mlg779
3 жыл бұрын
I am going the other way because I do not use wireless. I use a sol-ark inverter that only has a wireless dongle connected to a serial port. Is there anyway to connect an internet cable to that serial interface? I was thinking to sent the data from inverter, somehow to Grafana or Home-assistant but the inverter company does not offer offer any support on that on that and they only have the wireless connection that sends data to a server in China.. They just provided me with the mod buss RTU Protocol manual. I am brand new to this and I am willing to pay you if you can offer me some direction.
@DIYTechRepairs
3 жыл бұрын
Hi depending on protocol you can use My solar-sis system or code something else :)
@vb9528
Жыл бұрын
what kind of inverter are you using?
@HtikeAungKyaw
2 жыл бұрын
Seems like it doesn't work with Sorotec Revo II Inverter. Too bad... Sorotec uses SolarPower and WatchPower Applications via USB Connection or RS232 to view data on computer. I did most of the parts as you mentioned in the video except for the TTL Module. I used RS232 to TTL (MAX3232 Module). It did connect to the MQTT Server well but didn't talk well to the inverter. Both the red and green LEDs are on.
@DIYTechRepairs
2 жыл бұрын
If it uses watchpower it should work. Most commun issue is The ttl converter
@AnjumSohail
3 жыл бұрын
I think we can't simultaneously connect USB connection with and Rs232 connection with inverter, as Nodemcu has same UART I believe, but you have not used software serial library instead?
@DIYTechRepairs
3 жыл бұрын
No you cant use USB and RX/TX at same time on the esp8266 no. Its either or and its described in the video as well. I do that because running software serial towards this inverters is so unstable due to the libs. Its crashes to much. On the ESP32 though this can be remade but on other hand i have no use having to use the usb at same time as its connected to the modbus adaptor.
@JayJay-rb6rt
2 жыл бұрын
Thank you so much for this video. I would like to ask who is your mqtt server provider
@DIYTechRepairs
2 жыл бұрын
I run my own. I run Mosquitto
@turbosigma
2 жыл бұрын
Will this work with a mppsolar Hybrid V 4048. Does it issue a qpigs command? If so will be able to use it for monitoring.
@DIYTechRepairs
2 жыл бұрын
Look in The code
@AnjumSohail
3 жыл бұрын
Which mqtt platform has been used, can what alterations will be required if use Nodemcu istead
@DIYTechRepairs
3 жыл бұрын
I use mosquitto.
@electrichaidar7841
3 жыл бұрын
Hello, dear brother, we hope you will explain to us about RCD and RBCWA FFD with thanks
@ZulqarnainUlHassan
3 жыл бұрын
Very informative. Does this setup works with with other brand of invertors aswell. I mean the pinout from the RJ45 would be same for all brands?
@DIYTechRepairs
3 жыл бұрын
No they arent. The RJ45 in this case is only for the PCM60x. the device it self can be used for others that do serial and if you have the protocol.
@ZulqarnainUlHassan
3 жыл бұрын
@@DIYTechRepairs Thanks for the update. I am trying to do compilation of the code, the hard way, through ArduinoIDE. It gives out error at Line No 92 "exit status 1 'service WifiMode' was not declared in this scope". Help would be much appreciate.
@DIYTechRepairs
3 жыл бұрын
@@ZulqarnainUlHassan I just tested and no compilation error on latest version from Git. Can you copy paste the full error somewhere and link?
@bobkammoun8375
2 жыл бұрын
Hello, does this code work on nodemcu esp12e-8266 or it needs to be modified ? Thanks in advance
@DIYTechRepairs
2 жыл бұрын
It works but you May need to change port definitions
@roukozabboud1337
2 жыл бұрын
is the data accessible and can be used as part of a code for exemple setting up a buzzer using arduino?
@DIYTechRepairs
2 жыл бұрын
Sure Its open source
@abdullahhasan1769
2 жыл бұрын
Many thanks for wonderful piece of work. I was about to make that, but unable to locate the file src.ino.generic.bin in the source folder......can you help/share link pls?
@DIYTechRepairs
2 жыл бұрын
Its there.
@Maaz_Gaming29
Жыл бұрын
i want to add oled at sla and sda pin is it works or need to code diffrent
@Maaz_Gaming29
Жыл бұрын
at d1 and d2
@dannytech4709
3 жыл бұрын
Super Thanks ! Does it work with Schneider mppts ?
@DIYTechRepairs
3 жыл бұрын
Dont know
@FunnyFantasticFail
3 жыл бұрын
Is your 10kW inverter still running after repair? I am thinking about to order the same one.
@DIYTechRepairs
3 жыл бұрын
It is but it doesnt run 100% i would like to swap it out to be honest
@Patalhetas
3 жыл бұрын
hi, great job by the wy ;) this only working with this inverter, right ? is possible use in GTIL inverter too ? or how I change the code (i´m hardware man, not programming) :) regards
@DIYTechRepairs
3 жыл бұрын
thanks. dont know what protocol gtil have. out of the box it wont work no :)
@Patalhetas
3 жыл бұрын
@@DIYTechRepairs i have the protocol , i think :)
@duymelody3531
2 ай бұрын
Can it control the inverter? I want to change SUB - SBU mode remotely
@DIYTechRepairs
2 ай бұрын
Yes I can that
@duymelody3531
2 ай бұрын
@@DIYTechRepairs I have done what you instructed, then I can see where the result is
@PvBastler
Жыл бұрын
what kind of visualisation Software are you using?
@DIYTechRepairs
Жыл бұрын
Grafana and some home built code
@PvBastler
Жыл бұрын
@@DIYTechRepairs very nice, could you Show on KZitem, how we can make this too? Would be very Nice !
@estartermanual
2 жыл бұрын
meanwell TS inverter line not supported, right?
@DIYTechRepairs
2 жыл бұрын
Not unless they have same protocoll. But can be coded
@jamess1787
3 жыл бұрын
HES BAAAAAAAAAAACCCCCCKKKKKKKK!!!
@yuvarajblackpearl
Ай бұрын
will it work for esp32 ?
@DIYTechRepairs
Ай бұрын
@@yuvarajblackpearl could work.
@SalvatoreDePascali
3 жыл бұрын
Hi i made exactly what you show over the video but my Outback Power SPC III 5000W - Off-Grid Inverter - Hybrid dont recived any data. Do you know what is missing.
@DIYTechRepairs
3 жыл бұрын
What protocol does that inverter use? The device works with MPI and PCM devices and have code for PIP but its not properly verified. If you can hook up for debugging
@SalvatoreDePascali
3 жыл бұрын
@@DIYTechRepairs Hi how i know what protocol i need to use?
@DIYTechRepairs
3 жыл бұрын
@@SalvatoreDePascali read the manual for the inverter or talk to the manufacturer so you get the protocol
@MaximumPCs
3 жыл бұрын
Hi Daniel! Does this work with your MPI 10K Hybrid inverter over RS232? I am trying to do the same. Thank you in advance for all your help
@DIYTechRepairs
3 жыл бұрын
Yes it does. But There might be a codeverror. So let me know
@MaximumPCs
3 жыл бұрын
@@DIYTechRepairs sorry what do you mean by this?
@DIYTechRepairs
3 жыл бұрын
@@MaximumPCs I have fixed it. I had an issue in the code that i fixed locally but never pushed to git... DOH!!
@MaximumPCs
3 жыл бұрын
@@DIYTechRepairs wow great! I look forward to trying it =D it seems like a super simple way to send data from my MPI 10K to MQTT together with data from DIYBMS
@MaximumPCs
3 жыл бұрын
Another unrelated question - how have you connected your MPI 10K? Is your grid connected to the red ac grid connector and your house to the black ac output connector? Are you using it to export to the grid at all? I am using grid tie with backup (ii) mode but it seems to be using some grid power when solar is available doesn't make sense
@drc6940
3 жыл бұрын
Does anyone know how to send the MQTT messages to a specific topic? For example how to send these messages directly to node red or emonpi?
@DIYTechRepairs
3 жыл бұрын
You configure to send the data to your mosquitto server. Then you set emon or node to listen to Them. You configure the topic it sends to in the web ui
@zigavucic754
3 жыл бұрын
i can test PIP if you want,i have voltronic igrid 5kw 2 in paralell, pip 2,4kw low voltage solar and high voltage and 5kw high voltage solar, flashed your bin file but in mqtt config even if i set it to PIP it sends P003PS Message
@DIYTechRepairs
3 жыл бұрын
The latest release? Ping me on mail or github and lets take a look. I did upload new code a week Ago btw
@zigavucic754
3 жыл бұрын
@@DIYTechRepairs git
@MoAlisaab
3 жыл бұрын
Exactly what I've been looking for. I have the MPI 10 kw hybrid model and i gave the manufacturer SNMP card a try which died in a month. Awfull. Did you get this to work with your MPI inverter? Ive built this device and it connects to the inverter. I get the green light. In Mqtt explorer it reads all values as zero. I think it might have to do something with the communications protocol. In the Mqtt setting i choose MPI. Ive tried with the other two options and I get similar results.
@DIYTechRepairs
3 жыл бұрын
I have been running it solid since the start without issues. If you dont get data back that means you dont get answer from the inverter. Its important to connect the board that converts the signal from RS232 to the 485 that the inverter uses. If you have the knowledge you can hook up and debug the data on the tx2 port.
@MoAlisaab
3 жыл бұрын
@@DIYTechRepairs Thanks for the reply. My inverter has an rs232 female port on it. I could try using a esp32 to debug on the tx2 port maybe?
@DIYTechRepairs
3 жыл бұрын
@@MoAlisaab just connect it to the Serial adapter on your computer that you used for flashing
@MoAlisaab
3 жыл бұрын
@@DIYTechRepairs I think I know what the problem might be. There is a start bit that the inverter is looking for before a command "^" Im not sure how to input that into your code. Can I take you up on your paid offer to help setup? Thanks.
@DIYTechRepairs
3 жыл бұрын
@@MoAlisaab its already included in the code. If using correct type. But sure Contact me. Info on Contact page
@uzairtanveer666
3 жыл бұрын
hi any video for how to make mqtt server for this.
@DIYTechRepairs
3 жыл бұрын
If you run linux then install Mosuitto and you got the server :)
@bobkammoun8375
2 жыл бұрын
Hello again, does any body know what do we need to change in the code in order to get the data as INT not as STRING to get more accurate data. many thanks.
@DIYTechRepairs
2 жыл бұрын
The data is always returned as string since its serial. Just convert it from string to INT instead if you need it like that.
@bobkammoun8375
2 жыл бұрын
@@DIYTechRepairs I mean I am getting data like battery voltage as 24v without any decimals but in the video, it seems that there are decimals in the received data.
@DIYTechRepairs
2 жыл бұрын
@@bobkammoun8375 There is as well. You need to look at the raw data you get and convert it. I just forward the data as its recieved from the inverter :)
@bobkammoun8375
2 жыл бұрын
@@DIYTechRepairs Many thanks for your support.
@DIYTechRepairs
2 жыл бұрын
@@bobkammoun8375 it can also be confusion between , and .
@rashidrdm
2 жыл бұрын
Assalamualaikum I'm Muhammad Rashid from Pakistan. I like it. I need your help. I have VFD invt chf100 i want to make it wireless. Can you help me?
@DIYTechRepairs
2 жыл бұрын
Do You have its protocol? If so its possible. If its Close to same as mpp you can use My code as base
@rashidrdm
2 жыл бұрын
@@DIYTechRepairs it has 485 communication port and also some type of terminals as well. Please check specifications of invt CHF 100 VFD 15-18 kw
@erwinmariacher1413
Жыл бұрын
Thank you so much for this tutorial - i've solderd everything together; TX RX RS232 and TTL is correct; in the MQTT Explorer i get Infos that the device is alive and also the variables (e.g. solar1w...) but there are no values. Can you please help me? Thanks
@DIYTechRepairs
Жыл бұрын
Then you have a problem in the com between the device and the inverter. Either wrong protocol or its wrongly connected.
@MIUdk
3 жыл бұрын
Is the PIP supportet now? ☺️
@DIYTechRepairs
3 жыл бұрын
Should be but i cant test since i dont own One :)
@MIUdk
3 жыл бұрын
@@DIYTechRepairs Sweet, thanks! 😀
@DIYTechRepairs
3 жыл бұрын
@@MIUdk ping me when you installed it and i can help and or correct If something doesnt work
@VirusX87
3 жыл бұрын
@@DIYTechRepairs I have had the PCM up and running for a few weeks now working perfectly, i have tried the PIP however i am getting no output over mqtt, i have looked through the source and it appears the PIP section is missing with a message saying "This one is not done..."
@DIYTechRepairs
3 жыл бұрын
@@VirusX87 code is There but i hvae not been able to test since i dont own One thus adding that some Day back in time :)
@mohammedghassan1165
3 жыл бұрын
Hello sir how are you is there any way to communicate with you?????
@DIYTechRepairs
3 жыл бұрын
Dont know. I Guess you just did?
@mohammedghassan1165
3 жыл бұрын
@@DIYTechRepairs ihave a lot of questions
@mohammedghassan1165
3 жыл бұрын
I would like to inquire about the rear axle help me please
@DIYTechRepairs
3 жыл бұрын
@@mohammedghassan1165 you have Contact details on My KZitem about page
@mohammedghassan1165
3 жыл бұрын
@@DIYTechRepairs I have a rear axle of 120 cm space that I have to leave between the frame and the chassis
@user-lf2bl2mo4h
3 жыл бұрын
Hello friend, I would like to ask you about point D1 and D2 how far left and right angles are help me please ❤️❤️❤️ (Your follower)
@DIYTechRepairs
3 жыл бұрын
Hi Thanks. Not sure i understand what you mean?
@user-lf2bl2mo4h
3 жыл бұрын
Well, the topic is about building a Locost7. There are two points in the book called D1 and D2. How do I calculate the sides D1 and D2?
@DIYTechRepairs
3 жыл бұрын
@@user-lf2bl2mo4h ehh you know you replied to My video about wireless inverters right?
@user-lf2bl2mo4h
3 жыл бұрын
Yes, I know and I apologize for you because I commented on the video that is not related to the topic, so I said to myself, I will comment on the last video in the channel because you did not respond to a comment for me in the super7 series again. I apologize for the comment in the dedicated video in the following. Help me build the Locost7 (your follower)
@DIYTechRepairs
3 жыл бұрын
@@user-lf2bl2mo4h You have all the meassurements in the drawings. Im not sure what you should calculate. All meassurements is in the drawings. sevenesque.com/plans/
@drc6940
3 жыл бұрын
Has anyone been able to get the bin to load for an ESP32 yet?
@DIYTechRepairs
3 жыл бұрын
Its not compiled for the 32. You have to recompile it and of course recode it.
@drc6940
3 жыл бұрын
@@DIYTechRepairs Thanks Daromar. I am in the middle of doing it now and I will drop in my notes to this comment.
@drc6940
3 жыл бұрын
@@DIYTechRepairs Goddamn this is harder than I had imagined. I'm struggling to get the libraries updated for ESP32. Anyone else?
@DIYTechRepairs
3 жыл бұрын
@@drc6940 some Day i might recode it but since the 8266 is cheaper i run with that :)
@TattooSilence
2 жыл бұрын
I am so dumm i hab Problem Order the reiht wifi Modul you Bild your one
Пікірлер: 191