Love brother I was facing same problem and after watch your video I have a solution now😘👍😘👍🌹
@23chilled
3 жыл бұрын
Hello there. What is the value of the resistor that needs replacing before I try to locate a service manual? Save me a lot of hassle. Thanks
@TKFElectronics
3 жыл бұрын
4.7k ohm
@josevirginiojose7531
3 жыл бұрын
Será diodo proteção processador digital ativado marantz sr5400 liga sinal digital som mudo as vese central liga pré out tb mudo qual diodo deve levantar para desarmar proteção?
@josevirginiojose7531
3 жыл бұрын
Amigo moro brasil tenho receiver marantz sr5400 meses car receiver ligar indica sinal digital entrada mas não produz som as vese produz dolby music central será armou proteção placa digital onte abrir limpei cabo flat medir continuidade cabos td ok fechei tampa liguei tos cana funcionou no outro dia manhã liga sem som.que será?
@TKFElectronics
3 жыл бұрын
I am from India, pls write in English, thank you
@sathishsridhar249
3 жыл бұрын
The same av receiver I have.The problem with this is that it automatically goes standby mode when on it.When you turn it on two or three times it will go standby mode.When on a fourth time,av receiver showing ERROR POW5V.Humble themselves to suggest the right solution to this.
@TKFElectronics
3 жыл бұрын
Thank you very much brother for watching my video, their is problem of 5vdc not reaching to Main system CPU ic, therefore u r getting error that. So I suggest u if u r not qualified technical person do not attempt to repair it, where is ur location, my shop is in Mumbai, e-mail me on this electronicstkf@gmail.com
@sathishsridhar249
3 жыл бұрын
@@TKFElectronicsOkay sir.thank you for your reply.can you please send your whats app number
@TKFElectronics
3 жыл бұрын
Dear friend email me on this electronicstkf@gmail.com, I will send you no. Thank you
@TKFElectronics
3 жыл бұрын
+91 9653123582, u can call me on this
@josevirginiojose7531
3 жыл бұрын
I live in Brasil have i marantz sr5400 alloy but without stereo sound The sound comes out of The central surrund box seems to be protection diodo digital plate which diodo tô lift desarming plate.onte open cable clearning tested continuity cable ok. religueis cables closed l connected marantz soud all channels ok. Next day l turn on The sound does not come out stero and mute thank you if can help me.
@TKFElectronics
3 жыл бұрын
My dear friend, you mean to explain that your system is ON but no sound output coming from all channel right. This is the problem
@josevirginiojose7531
3 жыл бұрын
@@TKFElectronics that's right. l am a third owner silver model sr5400 believe it may be bad contacts flat cables go in and out digital card l have Basic eletronic notion Will test put tape part blue tighten but in all flat contact.👍🤝
@TKFElectronics
3 жыл бұрын
Mr.jose, it is quite hard to tell where is the problem without inspection, first check the setting of speaker connection as per operation catalog all speakers parameters setting, if this all ok, then may be fault is in your Power Amplifier board (bottom board) & if this ok then some Electronic components may be faulty in digital main Board . I hope you may satisfied with reply. Thank you friend.
@josevirginiojose7531
3 жыл бұрын
@@TKFElectronics dude l sold 8monthes ago had taken Electronics swap flat cable 15vias Was replaced by generic had clearence in contacts l put tape over it on The base of the cn27 to cn28 digital plate só far ta show everything activated thank you 🤝👍👌
@laxmanchaoudharisukhdeocha8480
3 жыл бұрын
May marantz emplifire,model no 2700 Ded, no powar start,plije gaied,🙏
@TKFElectronics
3 жыл бұрын
Pls call on this cell no. +91 9653123582 to know more in detail about u r Marantz Amplifier. Thank you
Пікірлер: 22