Be careful at 11:12 as you’ve assembled that wrong The final weight plate (smaller one) goes ON TOP of the weight selector bar
@alexgalvez7506
4 ай бұрын
I made that mistake 😅
@dbay22
3 ай бұрын
I came here just for this step, looked back at my paper and went "well that don't look right lol*
@sarahitangelita
3 күн бұрын
Ugh yeah. I did all of them wrong so I was eagle eying this step. Trying to figure out why my selector stick kept getting stuck instead of going down the hole. Well all my weights were upside down! But yeah this last plate in the video is upside down
@TheLegendOfTheFall22
2 жыл бұрын
Just finished building mine, it was so much easier watching your video. Thank you so much for it, I'm sure many of us gladly appreciate it🙏
@mitchbluntschly2921
3 жыл бұрын
I assembled this casually over 3 days. I have about 4 hours in it thanks to you and your DIY guide. The ratchet and Hex bits ($10 Amazon) are a must. The only thing I messed up was running the bottom cable under the bar on the front two pulleys. Took me 5 minutes to fix. Thanks dude!
@MasteringMayhem
2 жыл бұрын
You’re very welcome 🙂✌️❤️
@thesanerone
2 жыл бұрын
Great video! Just a heads up for you and anyone watching. The bar that supports the weights goes under the last small weight plate, not over. Check the drawings again. Time stamp on video 11:09
@walketim
Жыл бұрын
Yup.
@weavecity
2 жыл бұрын
Assembly would definitely not have gone nearly as smooth as it did without your video. Thanks, man!
@ronscott51
2 жыл бұрын
DUDE YOU ARE THE MAN. You are the first person after reviewing many video on people saying they are showing you hot to set it up but just want to collect likes. I really appreciate the step by step way you went about showing up how to install this workout station. Thank you so much.
@MasteringMayhem
2 жыл бұрын
You’re very welcome. Thanks for supporting the channel 🙂✌️❤️
@boxerblake1
6 күн бұрын
Building very similar model, but instructions were a bit convoluted on a couple parts. You cleared it up. Thanks so much!
@cvibe93
Жыл бұрын
Man I would not have been able to put my MWM-1005 without this video. THANK YOU SO MUCH for your service sir!
@ronnordstrom5418
Жыл бұрын
Excellent video! As many people have commented, the included assembly instructions are not clear or well illustrated in a number of steps. Your video was very detailed and informative. Thank you!
@GamblerLewis
2 жыл бұрын
Really great video. If you are like me and have the the 1005 model, this video is basically the exact same install with a few steps out of order. Manual for this model does not have the handy zoom in diagrams like the one in the video does so being able to slow this video down and watch really really helped. Thank you to the poster! Took me about 5.5 hours moving at a leisurely pace. Actually enjoyed the install! Was pretty fun! Thanks.
@robc9038
2 ай бұрын
Dude, thank you so much for this video. Usually I have a hard time putting things together. I thought this was gonna be so hard but thanx to u it was easy. Very easy actually. It took me 4 days to put it together but only because I didn't have a lot of extra time to put it together. So I just took my time. Thanx again man.
@marcholmes7509
Ай бұрын
Thanks a lot. My wife brought this equipment, without my knowledge. Your video was a tremendous help!
@johnfammi7741
Жыл бұрын
It took 150 hrs to assemble I was building muscles putting it together
@MasteringMayhem
Жыл бұрын
Glad you got it done though 🙂
@detraed8962
11 ай бұрын
lol same here. I got a work out putting it together. 🤣
@JohnnyOgres
2 жыл бұрын
I just assembled the 990 (same thing) after watching this video. Took me about 4 hours total. Your tips probably saved me at least an hour of time and countless amounts of frustration.
@chyguy9132
2 жыл бұрын
989 and 990 are exactly same so I could watch a video of a 990?
@CHRISHUNT2604
2 жыл бұрын
Used this to guide me on the construction of my MWM-1005 in the UK and it was really useful. I haven't worked out how to fix the ankle attachment to the cable, I have a spare back plate (part no. 20 in my instructions) and one small fixing pin (part no. 72) which for the life of me, I cannot work out what it does! However it all works and I'm really pleased with the end result. Took me two days, very casually. Could have done it in one at a pinch. I have to say, the US instructions used by the gentleman in the youtub vid, were much clearer than mine, which appear to have been drawn in the Far East and then translated to a very small print booklet. I'll probably re-watch to see if I can work out what I missed.
@shannansopko5456
Ай бұрын
Is there a way to fix the weight selector plate issue you guys are talking about without taking the whole thing apart? Also do you need to take the carabineer off the lat bar every time you want to use the ankle cuff? Anyone else have a problem with seat being too low to properly use the pec deck? And what is the small 90 degree angled pin I have left over used for? Thank you for any input on any of these things and thank you for this video. It helped a lot!
@RooLizard33
8 ай бұрын
This video was such an incredible help. My 14-yr old son and I watched it while putting ours together and it made it SOOOO much easier. Thank you so much for taking the time to make such a great video! Yeah, it took us 4 hours, and we started at 8p on a Friday night, but it was quality time with your video providing great guidance!
@johnyreehal8122
3 жыл бұрын
Just to let you know , you insert the last small plate upside down . The small plate should be inserted after the T bar and the notch should be facing down to always pushing the T bar down so all the holes match with bigger plate holes. Thank you
@afernandez1027
2 жыл бұрын
What step is it ?
@zebman9228
2 жыл бұрын
What does upside down mean? The upside would be the correct side up by definition of the upside. Are you saying do not follow the instructions?
@richardcope6523
2 жыл бұрын
I came to the comments to see if anyone else noticed. The last plate should cover the t post part of the weight selector bar.
@jordanj6446
2 жыл бұрын
Do you put the metal ring on the t bar before or after the small plate?
@jordanj6446
2 жыл бұрын
The last plate don’t sit flat if I put it on before
@babuthomas7271
Жыл бұрын
Excellent video , without this video I couldn’t have assemble this equipment. Thank you so much.🙏👍
@tangoindiamike9189
2 жыл бұрын
I just assembled mine a few weeks ago. Your video popped up in my feed about a year too late, but I just followed the booklet instructions and got it done in several hours.
@Darthrtrader
2 жыл бұрын
I just built my Marcy 4965 gym yesterday and it took about 6 hours. For the life of me I could not figure out where to put the ring for the plate pin. I skipped around your video and stopped on the exact spot where you put it on top of the plate pin shaft. It's funny because your directions told you where to put it, mine didn't. LOL Thanks!!!
@MasteringMayhem
2 жыл бұрын
You’re welcome. Glad the video helped 🙂✌️❤️
@fordescape2008ful
Жыл бұрын
Exactly, i am soo hangry, i did the same error at 11min16 and trusted you... i will try to correct without broking grrrrre
@stephaniesullivan7072
Жыл бұрын
You have no idea how much this video helped me! If it wasn't for this video I would have kept it in the box for another few years at least!! Thank you SO very much for this tutorial!!!
@MasteringMayhem
Жыл бұрын
You’re very welcome. Very glad it helped you get the equipment assembled. Thanks for supporting the channel.
@Ernestkun
Жыл бұрын
OMG thank you so much! I was struggling all day because my guide was so ambiguous. Couldn't have done it without you!
@MasteringMayhem
Жыл бұрын
You’re very welcome 🙂✌️❤️
@ahmedalhasan9226
Жыл бұрын
I just want to say thank you. I got the Marcy model 7119 and the instructions that came with it were really crappy. You sir are a life saver.
@MasteringMayhem
Жыл бұрын
You’re welcome. Thank you for the support 🙂
@morrisf3957
Жыл бұрын
2nd hole tension the most I could get with the t bar bolt all the way down.great assembly video.
@MegaKINGANTHONY
3 жыл бұрын
My wife and I just finished working out I think overall it’s a good home gym my only complaint is that I wish the weight can up up about a foot more so I can a comfortable extension
@LLAMA-LLAMA
3 жыл бұрын
We don’t have much interest in gym equipment, but after having all the fun on Saturday night Mayhem and watching your other tool videos we find ourselves watching them. Nice assembly and explanation.
@MasteringMayhem
3 жыл бұрын
I don’t know how much longer I’ll be posting these kinds of videos...probably until I don’t have to make them anymore. They do pay consistently so, until I’m home to do KZitem full time, you’ll see these here and there 🙂✌️❤️
@user-ou4vk5td4w
7 ай бұрын
This was one of the best videos I've ever used.
@MasteringMayhem
7 ай бұрын
I appreciate that. Thanks for the support
@vaskarsubba164
2 ай бұрын
W video me and my dad finished it under 3 hours thanks man
@lenellesunboxings6795
Жыл бұрын
We bought the 1005 gym and if it wasn't for you, I dont know if we could of put it together right, we Thank You so much for the video and instructions and tips. We followed your steps and would pause it and do ours and go back to you and so on. Whew! Greatly appreciated .
@fifi6647
3 жыл бұрын
Thx for this video,just assembled it in 5 hours... couldn't of done it without this video...very helpful...many thanks again
@MasteringMayhem
3 жыл бұрын
You’re very welcome. Enjoy your new fitness equipment 🙂✌️❤️
@pattitahmazian6088
Жыл бұрын
Yes, I noticed this too. The pin attachment needs to go between the last 2 weight blocks, not on top of the last block!!!
@tnjzingbling2563
Жыл бұрын
I can. It gets the foam arm rests on I. To weak what's the trick or should I cut and tape them or just leave them off
@MarcyFitness
2 жыл бұрын
Feel free to click the link below to our assembly video of the MWM-998/990 kzitem.info/news/bejne/mI-hyGiJfn6iq2U
@MasteringMayhem
2 жыл бұрын
Hello. Please let me know if you all have any affiliate opportunities. I will be posting a few more Marcy fitness equipment assemblies. Reach out via my email. Either way, you all have a great holiday. 😊✌❤
@trblhdfun
Жыл бұрын
Without your instructions this gym was not going up. Thank you and I think Marcy should be paying you.
@MasteringMayhem
Жыл бұрын
I appreciate that. I agree @marcyhegym 🙂
@tonycat721
2 жыл бұрын
The one thing i did no do was to weigh the plates ...... too late now i have complete build it... i think i used you vid more than the instruction manual ........... thank you ..
@pedorseyiv2426
Жыл бұрын
Just got the -1005 from Sam’s Club. Basically the same. The booklet instructions are not great but really need this video to help with the tension that you pointed out at the end. Thanks
@anew1297
8 ай бұрын
Thank you. That one part with the cable caught us as well. Your video helped immensely.
@MLangevin
2 жыл бұрын
As others have mentioned our instructions were a bit different and not nearly as detailed so this video came in very handy.
@dntchase_replace362
2 жыл бұрын
Thank you so much for making this video! I would not have been able to put together my MWM-1005 without it. The instructions provided weren’t clear at all.
@MasteringMayhem
2 жыл бұрын
You’re very welcome 🙂✌️❤️
@tylergraham9537
2 жыл бұрын
You can the same one I got than
@pedorseyiv2426
Жыл бұрын
Yeah I had a problem with the poles being uneven. The instructions did not say anything about making holes straight. Thanks
@Behold876
6 ай бұрын
Thank you so much sir.. Couldn't do it without your video. Thanks
@stocktonRolloffDriver
7 ай бұрын
Thank you again...appreciate it..made it easier for me forsure...
@ma-so1kb
2 жыл бұрын
Brother hands down ya did a fantastic vid and set up !!! Jus picked 989 up yesterday and started AM “8am” today lay out plan made ALL the difference and the satisfaction once finished keeps the adrenaline pumping into my first workout🔥 the easiest part was running cable for that I honestly jus looked at booklet …you definitely kicked @$$
@zebman9228
2 жыл бұрын
Why are there holes half way up verical rods and why does it matter how they are lined up ?> The Marcy official assembly cartoon video seems to have these same hole 90 degrees from how he Mastering Mayhem gives instructions re these holes at 4:18.
@eric1135
2 жыл бұрын
Just assembled mine today. The holes are for the combination lock and pin to child proof it. It does not matter which way they face as the lock works with them facing forward or sideways. Great video and I found it very helpful, but I was worried about this step since he stressed it so early-and the official manual has them facing the other way. Again, it doesn’t matter.
@williamaldarondo5536
3 жыл бұрын
Greetings, I just bought the marcy home gym mwm 1005 and its the same and you made it look easy.. while i was assembling mine i saw that on your machine you installed the cover weight upside down... and the selector bar would go first... its a miner detail but i think the selector bar wouldn't go as far for selecting the last weights... over all its a awesome vid and i'ved watched a few time while assembling mine, thanks
@williamaldarondo5536
3 жыл бұрын
@gamer boss let me see, i don't know if I explained it right, where the sector bar goes, there's a top weight thats different of the rest... the way I put it on my machine was that even if you don't select any weight it will be on the selector bar... its a miner detail... i hope i explained my self... if not maybe I can send you a pic of my machine... let me know have a great one. 👍🏽
@williamaldarondo5536
2 жыл бұрын
@@mladenalexander8754 sorry to get to you so late, my cel broke and couldn't get to my accounts, i'm glad you could resolve that issue, have a good one 👍
@rachiddoul8591
2 жыл бұрын
Thank you I could not build without your video.
@jodir6114
Жыл бұрын
I can't get the foam arm pieces (27) on the pipe 9&10. Any ideas? I can get it started but it's too tight to move into posiiton.
@geeder9086
3 жыл бұрын
Nice video! I'm putting together my MWM-990 right now -- it looks [identical] to your model. I had a crooked mount for the rear base bar where the facia panel for the stacks connect. The hole was off by about an inch -- but a few whacks with a hammer straightened it to 90 degrees. The facia panel is also dented in bent in several places -- I might need to have them send me another. It looks like they didn't pack enough #65 washers in mine. Last time I got a Marcy bench they replaced a cut preacher pad (somebody used a razor on the box, not me) -- no questions.
@thomasmorse6692
3 жыл бұрын
I wasn't ready for such a weighty subject but I stuck it out to the end. I'm stronger for it but next time I will stretch first.
@valeroush2407
Жыл бұрын
More thanks sir with your help putting together my MWM 1005 and all is good. 😊
@MasteringMayhem
Жыл бұрын
You’re welcome. Thanks for the support
@erikw9226
Жыл бұрын
I assembled a Marcy 4965 and the cables have to be pulled way to far before it engages the weight. Any suggestions as to what I may have done wrong? Thank you!
@selomdoke5687
8 ай бұрын
This video could not be any nicer. Thank you Sir!
@rupindersinghdhillon2294
Жыл бұрын
Really appreciate your video, brother you make my job easy . Thank you.
@MasteringMayhem
Жыл бұрын
You bet. Thanks for the support 🙂
@Cry4America
8 ай бұрын
Thanks - you helped me do this myself 🎉
@MRSclypse
2 жыл бұрын
Thank you, Thank you, Thank you!!! Our instructions were a little different from yours but your video helped us power through! Especially the timing for adding the weights! We are looking forward to using it after the workout of putting it together :)
@MasteringMayhem
2 жыл бұрын
You’re very welcome. Thanks for supporting the channel 🙂✌️❤️
@derrick6112
Жыл бұрын
I was soo confused. Thanks for shedding the light.
@MrDugath
2 жыл бұрын
Thank you for this. My instructions for some reason we're printed slightly differently and very hard to make out. Following what you did helped alot.
@danundisputed3189
2 жыл бұрын
Thanks for the video. There is an issue that the top cable seems to be shortened after all pulleys were installed. I had to lift the weight support rod about 8-9 inches higher to fit all pulleys and cables. What could be wrong here ?
@RespectGamez
2 жыл бұрын
If it wasn’t for you and your video I would be lost fam. Much appreciation and happy holidays 2021
@MasteringMayhem
2 жыл бұрын
You’re very welcome. Enjoy your new equipment. I hope your 2022 starts off well for you and yours. Thanks for supporting the channel 🙂✌️❤️
@MrEach1Teach1
3 жыл бұрын
Thank you! you saved me money! your video was excellent and easy to understand.
@MasteringMayhem
3 жыл бұрын
You’re welcome. Thanks for supporting the channel 🙂✌️❤️
@luillopr314
3 жыл бұрын
Veryhepfull... greetings from Puerto Rico 🇵🇷
@yogi_d8508
2 жыл бұрын
A great help. So glad you made this video. Instructions could be better. Thank you very much.
@RC-Panama
2 жыл бұрын
Thanks so much for posting this video. It answered all the questions I had on certain sections. Appreciate it!
@socio8096
Жыл бұрын
Just finished putting mine together thanks for the video tutorial.
@MrPhilmckrevis
Жыл бұрын
Well done young Sir!!! Massively useful
@jesusjrmelendez2103
2 жыл бұрын
Thanks so much for helping me build it
@bobbicarriger7248
Жыл бұрын
Thanks!
@footballvideos8327
11 ай бұрын
Hello! We just put this together and have piece #72 left over. It’s on the final page diagram but not in the instructions. Where does that piece go?
@briansutter7696
5 ай бұрын
Just put this gym together, and like you had, piece number 72 is left over, and I can't tell where it goes. The diagram isn't clear. By any chance, did you figure it out? Thanks
@khaledgarwash1728
2 жыл бұрын
Thank you for an amazing video, I referred to it to set up my Home Gym MWM-1005. The instructions that came with it were rather confusing. Keep up the good work, dude!
@chrissmallears
3 жыл бұрын
The time lapse didn't help me. Can I pay someone to come install it for me
@WBSmith-ol7sn
2 жыл бұрын
I just got mine and finished putting it together.
@kevonmartinez8350
Жыл бұрын
Excellent video, just finished putting mine together , was easy watching your step by step...thank you.
@daniyal.2741
Жыл бұрын
Thank you for the video. But you did a mistake in step 7, the bar should go in first, and then you should put the final weight on top, as the instruction shows This is to make sure that the minimum weight you can choose for exercise is the top final weight which is 10 abs, and not 0 lbs as you assembled.
@lorischuster6224
2 жыл бұрын
Thank you! This video helped so much!
@detraed8962
11 ай бұрын
Do you know of a simple way to remove the weights ? I put some of the weights in the wrong direction.
@kevq35
2 жыл бұрын
I knew I wasn't crazy, in my instructions the 4th step was to add weights. Your step 4 is my step 6, but my diagram has the weights added already (I planned to do it your way). Someone messed up the instructions. My model is MWM-1005, but it's the same.
@MasteringMayhem
2 жыл бұрын
I had to learn it the same way. Sometimes the instructions make things more difficult. 🙂✌️❤️
@Bassmanwcm
Жыл бұрын
How did you get the foam to go on so easy...mine seems to be to tight?
@fareedhamil7394
2 жыл бұрын
Great video.First plate needs to be upside down with the plate holder underneath,in order to get it low enough to reach the bottom plate.
@thekidsofawesome3678
Жыл бұрын
Top cable appears to be too short to screw into the weight selector t-bar piece. Any ideas? Am I missing something?
@marcomendez5757
2 жыл бұрын
Thanks man saved me 200 bucks
@MasteringMayhem
2 жыл бұрын
You bet 🙂✌️❤️
@WBSmith-ol7sn
2 жыл бұрын
I just purchased the mwm989 and the poles that hold the weights show the holes on the side not facing forward. Now I'm stuck trying to see which way is right.
@GameAtol117
Жыл бұрын
Thank you so much, but this used and disassembled and couldn't figure out the pulley system!!
@jerryshafer1688
Жыл бұрын
Part #72 - there is no place for it in the instructions?
@marleneyearwood3139
3 жыл бұрын
Thank you, Sir. Your video was really helpful.
@walketim
2 жыл бұрын
Dude. Thank you.
@rohitsharma-xz3se
3 жыл бұрын
Thank you for share this video sir......its help a lots
@garysmith2048
3 жыл бұрын
what did you do with part 73 & 74 (lock pin and combination lock)?
@teriana24
2 жыл бұрын
I am curious about that as well
@user89214
Жыл бұрын
Great video! Helped me build my 1005 ! Thank you!
@TheChandler1
2 жыл бұрын
I appreciate the help but tbh the time lapse defeated the whole purpose of the video. Shoulda just kept it in normal speed
@AnsiGaming
3 жыл бұрын
0:49 My machine didn't come with the part 41! The rubber stoppers etc. I saw that yours didn't either! Is it okay to build the gym without it? I just wanna get it over with. I looked everywhere and I can't find the rubber stoppers for the two poles which is part 41.
@mizterperfecto1012
3 жыл бұрын
Me either I think we’re good without it
@alesiaf4798
Жыл бұрын
Any suggestion on how to get the back pulley 26:59 in to stay straight? it keeps curling the cable in the other direction
@bozopriester
2 жыл бұрын
You are absolutely wonderful!!!!!! I bought a (barely) used Marcy Pro from a fella who couldn't find the assembly instructions. We disassembled only as much as we needed in order to fit it in my car. Your video helped the reassembly process immensely, even though mine is a slightly different model (the cabling is the exact same). Thanks again!!!
@johnnyrotten9853
2 жыл бұрын
Hey, where does the second cable attach to? This is the only issue I’m having right now
@Aventuras_JP
2 жыл бұрын
Very helpful thanks so much , thanks to you i was able to build this machine step by step 👍keep up the good work
@H0plite99
2 жыл бұрын
Did it without the video in 2 nights, about 3 hrs each night. Not too bad. Just a little cussing and swearing when repeatedly dropping the hex nut wrench and having to step down to get it but hey that's good exercise :D
@bluefox12factsbeforefeelin58
2 жыл бұрын
Bro seriously thank you so much 💪🏽💯
@geeo1965
Жыл бұрын
Whats the lock and the little L shaped pin for????
@stevesutton3996
Жыл бұрын
Good question. Scratching my head over that one too!
@geeo1965
Жыл бұрын
@@stevesutton3996 The L shaped pin goes in the weight lift rod in the back of the panel. Then the lock lockes it in place to prevent anyone from using the stack. It took me a minute....
@saanvisamazingworld306
2 жыл бұрын
Thank you so much for the detailed explanations! We saved $200 with your help 😀 All set to go!!!?
@MasteringMayhem
2 жыл бұрын
You’re very welcome. Thanks for supporting the channel 🙂✌️❤️
@denisvatamaniuc3510
2 жыл бұрын
Good job! Thanks for the video! It helped a lot.
@WarmThread
2 жыл бұрын
Thank you, That was helpful. Great Job man Keep the good work.
Пікірлер: 224