Omg..thank you sir..i was finding these calculations but you made very easy….thank you
@mastermechanicaldesign
Жыл бұрын
Glad to hear that 😊😊
@vinayakbhoee6488
8 ай бұрын
Hi Ayush,waiting for Powered roller chain conveyor calculation video
@mastermechanicaldesign
8 ай бұрын
It will take some time. First we will complete bearings sizing and calculation parts
@selvasenthil1997
18 күн бұрын
Really I got nice knowledge about the selection of motor and gearbox, thank you so much........ Still having some doubts from this video @ 16:03 MOI of an object in linear motion is 0.208 Kgm^2.....But actual calculation as per the mentioned formula 20.165 Kgm^2 coming.....Correct me If I am wrong........
@mastermechanicaldesign
3 күн бұрын
Hey, yeah there are some typo mistakes, your calculation are correct.
@ossielcontreras9543
4 ай бұрын
Awesome explanation, very complete. Thanks a lot!! Keep going with more videos, Bro!!
@mastermechanicaldesign
4 ай бұрын
Glad you liked it!
@maymocthietbi6105
5 ай бұрын
Very good video , thanks Master
@chintanbeladiya1058
9 ай бұрын
It was so amazing explanation 👏 Thank you bhai
@mastermechanicaldesign
9 ай бұрын
Most welcome 😊
@ALAPUSATYANARAYANA-uu4dv
8 ай бұрын
Mostly valuable information sir thankyou.
@mastermechanicaldesign
8 ай бұрын
Most welcome
@learnwithveeru
Ай бұрын
Thanks for sharing good information. If possible please do about power roller conveyor design calculations
@mastermechanicaldesign
Ай бұрын
Sure, I will
@dhirajsoni8792
Жыл бұрын
Kindly Make a video on calculation of axial and radial load for bearing selection.
@mastermechanicaldesign
Жыл бұрын
Sure dhiraj, Complete bearing series is planned.
@FERONIK99
7 ай бұрын
You are great sir ❤
@sureshvijay604
Жыл бұрын
Please explain once the Servo press calculation and selection
@mastermechanicaldesign
Жыл бұрын
Hi Suresh, Servo motor selection calculation ??
@sampathcm5054
10 ай бұрын
Very good and informative videos bro ... thankyou.. i need one clarification, how do select dia of the roller? Is there any standards? And torque based on MOI is it finding for all the drives?..
@mastermechanicaldesign
10 ай бұрын
There is no such standard, but yes roller diameter should be sufficient to roll the belt properly. Means if we take a thick belt then we should consider a large diameter. Also we should try to keep the roller diameter minimum to reduce the MOI Third yes strength but it depends on length and tension on the roller (no significant concern)
@sampathcm5054
10 ай бұрын
Thankyou ❤
@praveenchoudhary5137
Жыл бұрын
Sir ek question hai for example if customer need 100 part in one minute at the end of conveyor then what should be belt speed...means how we will calculate belt speed???
@mastermechanicaldesign
Жыл бұрын
Hi Praveen very interesting question ❓ Here belt speed will also depend on part length. And gap between each parts Let say part length is 100 mm at a gap of 50 mm. Mean conveyor belt should travel 150 mm for one part delivery. And as given 100 part per minute. Mean 100x150 mm per minute 15000 mm per minute, 15 meter per minute. Please let me know if I'm making mistake in calculation 😅
@sumanchand9937
4 ай бұрын
Sir make video on motor selection of servo motor for shaft rotating
@mastermechanicaldesign
3 ай бұрын
Noted !
@annaidu583
2 ай бұрын
thanking u sir u are really good and excellent knowledge in this topic i understtod and learned so many points sir explanation is very clear and awesome 👌💯🙏
@mastermechanicaldesign
2 ай бұрын
You are most welcome
@merugusravan4825
2 ай бұрын
We need more videos on moment of inertia
@mastermechanicaldesign
2 ай бұрын
Okay!!
@niranjanrawle3488
8 ай бұрын
Power and torque calculation for a shaft carrying cam and rotate with 150 rpm and cam also carrying a load of 200 kg
@mastermechanicaldesign
8 ай бұрын
Cam Shaft Torque = (Normal Force of cam follower on cam) X (distance from cam shaft center to point of contact between cam and cam follower) (tan a (pressure angle))
@nikhilpathak5005
Жыл бұрын
Need a video on procedure for selection of timer belts
@mastermechanicaldesign
Жыл бұрын
Sure, Noted ☺️
@mohankumaras5189
10 ай бұрын
Big Fan Broo .. ❤ please tell me what is the PPT model and animation you using for this presentation.. It's fantabulous..🎉
@mastermechanicaldesign
10 ай бұрын
Thank you so much mohan, PPT model - mostly i design models in solidworks and some images i took from internet. Animations - mostly i do in MS PowerPoint and also in solidworks animation. For b rolls - either i use stock videos or i shoot in workshop
@aniketwalapkar
7 ай бұрын
If the conveyor has an inclination what steps should be added?
@mastermechanicaldesign
7 ай бұрын
Hi, Aniket, In an inclined conveyor we have to consider a cosine value (angle value) in mass, which will add up into conveyor pull force
@KrishSivaperiyanayagam
3 ай бұрын
Excellent lecture bro, can u pls explain the calculation of acceleration time in detail
@mastermechanicaldesign
3 ай бұрын
Ok noted !!
@automationguy9760
7 ай бұрын
Pls make a video of moment of inertia
@mastermechanicaldesign
7 ай бұрын
Noted ☺️
@sagarbhapkar9155
Жыл бұрын
Sir i want to now whole process of selection regarding gantry system vertical and horizontal movement with rack and pinion mechanism
@mastermechanicaldesign
Жыл бұрын
Okay 👌 Noted, Complete series
@jaypeepal8593
Жыл бұрын
Awsome video sir ❤❤
@mastermechanicaldesign
Жыл бұрын
Thank you jay 😊😊
@sivasugandan5381
Жыл бұрын
Usefull video...thank you bro
@mastermechanicaldesign
Жыл бұрын
You welcome sivasugandan 😊
@nishantdhengre8569
10 ай бұрын
Is there any documents or validation documents for your calculation
@mastermechanicaldesign
10 ай бұрын
Not exactly. But i would say whatever I have explained is pure physics, like power formula, speed, MOI etc. Plus for data reference i have given is from manufacturers catalogue. Which you can verify. However if you need specific parts validation, then i can provide. In terms of formula.
@vinaypatil4424
5 ай бұрын
sir we required your complet assembly desigen for study perpose
@mastermechanicaldesign
5 ай бұрын
Share your email id. I'll send you link
@exergy_thedigtallibrary8334
4 ай бұрын
Can you elaborate inclined convayor.
@mastermechanicaldesign
4 ай бұрын
I'll make a video on it
@trieunhat6535
4 ай бұрын
Why is the loading torque smaller than the starting torque in this video?
@mastermechanicaldesign
4 ай бұрын
Could you share time stamp
@littlestguy9589
5 ай бұрын
Hello. Thank you for the video. Where did you get the acceleration times from? "0-2 seconds for 1/5 hp" etc.
@mastermechanicaldesign
5 ай бұрын
This is actually a range (a rough estimation) because acceleration depends on how much the initial load is over the motor. I have taken this from a research paper from ABB laboratory
@pratikt9615
Жыл бұрын
Idler rotatating calculation video 😊
@mastermechanicaldesign
Жыл бұрын
Hi Pratik, To calculate the ideal roller speed, You can use the same formula of conveyor roller speed, only you have to put the ideal roller diameter instead of roller diameter. If Idea roller don't have much slips
@sandeepkumar-qh4mg
Жыл бұрын
गुरु बिन मंगल फेरते गुरु बिन करते दान गुरु बिन सब निष्फल गया, वाचो वेद पुराण
@bejrusxs4816
5 ай бұрын
I have a question, whether the formula above can determine a DC motor for a conveyor?😅
@mastermechanicaldesign
5 ай бұрын
Conveyor driving capacity. Like torque and speed will be the same for all types of motor
@bejrusxs4816
5 ай бұрын
@@mastermechanicaldesign Thank you sir, for replying to my question😁
@vivekmagar7776
3 ай бұрын
1)If I have flat belt conveyor with drive pulley and driven but both are different diameter then belt speed is change or not 2)same question for timing belt
@mastermechanicaldesign
3 ай бұрын
Belt speed will always depend on driver pulley. If both pulleys are the same dia. Both will rotate at the same speed. If driven pulleys is smaller, will run faster. If driven pulleys bigger, will run slower. Belt speed will be same.
@vivekmagar7776
3 ай бұрын
@@mastermechanicaldesign 1. For flat belt is same belt speed if we change diameter 2 but belt speed changes in timing belt if both pulley teeth are different
@sampathcm5054
10 ай бұрын
I have a big problem, when we should use Totque= Fr and T=I x alpha.
@mastermechanicaldesign
10 ай бұрын
Torque is required to rotate something (some load or weight means force F) at some distance (r) then we use T=Fr But when we try to rotate something from the middle like a conveyor roller, then we should also consider the moment of inertia of roller than required torque to rotate the roller about their axis will be MOI (I) x rotation acceleration (alpha) I know this can't be clear in text, so i would plan to make a video on it
@sampathcm5054
10 ай бұрын
Thank you sir please make a video.. am waiting .
@smitkotadiya7239
11 ай бұрын
Calculation for gradient conveyor?
@mastermechanicaldesign
11 ай бұрын
Calculations concept will be exactly the same, Just include the force cosine component as per conveyor gradient angle, (Like in sliding Friction, MOI of belt and load)
@bharathkrishna9669
4 ай бұрын
Can you attachvexcel calculation sheet
@waweeee5080
8 ай бұрын
Hi Sir can I ask where did you get or what book did that table of density came from?
@mastermechanicaldesign
8 ай бұрын
Hi, this table is taken from MISUMI (an automation products manufacturer)
@JayasankarJ-p2l
7 ай бұрын
Amazing
@mastermechanicaldesign
7 ай бұрын
You are amazing
@royalcouple5319
5 ай бұрын
Sir ap ka class hai kay
@mastermechanicaldesign
5 ай бұрын
Nahi. Avi bs yahi pr hai
@akashdoshi7879
7 ай бұрын
Which motor is selected if mass is too low Specifications Width of belt:152mm Number of bottle:50 Mass of bottle:750grms Roller dia:50 mm Belt thickness:5mm Matrial:pvc
@akashdoshi7879
7 ай бұрын
Also gearbox too
@akashdoshi7879
7 ай бұрын
Also belt lenght is 3m
@mastermechanicaldesign
7 ай бұрын
If you are using this conveyor, just to start and Stop. Go for an induction motor.
@akashdoshi7879
7 ай бұрын
but my output hp is too low like 0.00791 hp which induction motor availanle at this range
@mastermechanicaldesign
7 ай бұрын
You can take Higher size like quarter HP. Or take do check out Oriental motor (AC single phase, very compact gear motors are out there)
Yes I haven't mentioned Gearbox efficiency, However As i have already considered the MOI of Gearbox. So this is actually the cause of reduction in efficiency of a Gearbox (MOI and friction between teeth)
@johnwicked6667
10 ай бұрын
Can you provide the entire transcript of calculation in pdf..as my simple guide in conveyor belt calculation.thanks in advance
@mastermechanicaldesign
10 ай бұрын
Okay 👍, Yes it would be useful
@furqanshethwala1224
5 ай бұрын
Well Done Sir, As An Engineer I can say that your Channel will help most of Person who belongs to Machine Design field 👍
@mastermechanicaldesign
5 ай бұрын
I'm so glad 😊
@DavidRoss-h4l
9 ай бұрын
Excellent tutorial, created a spreadsheet from this for future conveyor designs. What additional do we add if the conveyor is inclined?
@mastermechanicaldesign
9 ай бұрын
Thank you 😊😊 Mainly Pulling force for motor, will increase, Cosine component of frictional force (Vector physics) will be added in total pulling force. 👍 I will make detail video on include conveyor calculation also, very soon.
@derlanmarzela
Жыл бұрын
frictional force = 0,2 x 411,5 x 9,81 = 807,3 N
@mastermechanicaldesign
Жыл бұрын
Yes, please bear with me for example calculation mistakes, take the formula and put your own required values. Apart from calculation typing mistakes every thing is right 👍
@santiagoaldohuamaniolivera7619
4 ай бұрын
haha I was wondering where is the x2? 🤔, thank you.
@joaogarcia9855
5 ай бұрын
My sincere congrats for the detailed explanation on the motor selection; it's reassuring to find that there still are some decent material not solely based on unbiased simplifications! I have a question tough, would you mind helping me out if possible? If the conevyor belt is designed to be pre-tensioned and mounted on top of rollers, in order for an object to move, there must be no slipping between the roller and the belt, right? Hence, the friction is the force pushing the objects forward on the belt and is not a resisting force, meaning there is no pulling force, likewise you mentioned at 11:02. In that case, the only torque is due to the inertia, correct? Does that mean that, when the object has achieved its final velocity, all power given by the motor is spent by friction on bearing, gears and others? Thanks in advance for the video, have a nice day!
@mastermechanicaldesign
5 ай бұрын
Thanks Joao Garcia, Lets discus! Point 1: There must be no slipping between the roller and belt, right? - Yes, it would be better if it is not slippery, but practically zero slip is not possible as you know. Point 2: Friction pushing the object forward on the belt and is not a resisting force- Yes absolutely right. Your last point, all power given by the motor is spend by friction on bearing, gears and other after reaching final velocity- This is complicate, yes this is 100% true that motor required torque will decrease after reaching final velocity means at zero acceleration. but as we are moving a belt, so there will be always a belt rolling friction, (thick belt means more rolling fiction), also there is not only roller MOI, but there is also transferring object and belt itself MOI which always being influce by gravity, as you said, motor is spending by friction on bearing, gears and others, so this term other is going to always much larger as compare to bearing friction.
@joaogarcia9855
5 ай бұрын
@@mastermechanicaldesign Thanks for the response, it makes sense: wile it's true there must be no slip and hence the friction is not a dissipative force at first, it's hard to guarantee no slip, which is hence the dissapative force when the final velocity is achieved. Therefore, while it's not correct stating there is not dissipative friction, it's also not correct stating the pulling dissipative force is F_pull = (load_weight) * friction_coef. , right? Unless we consider "friction_coef." beign much smaller than the actual kinematic friction coefficient. For rxample, rather than adopting 0.2, we take 0,05. Do you thing that's a reasonable approach? The losses in bearings, gears and other I'll consider by using their efficiencies as 99% or 98%, for example. Once more, thanks for the responses, for the video and for the commitment on the subject!
@mastermechanicaldesign
5 ай бұрын
Let's think in this way, 1. To move the belt, a strong frictional grip between rollers and belt is required, stronger the frictional griper of roller will give better will be result in terms of slip resistance, (So, sometimes we do knurl over rollers surface for better grip) in other word, frictional force between roller and belt should be more than frictional force of belt with conveyor's other parts (belt bottom support) with the load over belt. means, Friction force between roller and belt (depends on amount of belt tension, roller contact arc with belt and static co-efficient for friction between rollers and belt) should be grater then frictional force of belt (loaded with material) and belt support plate, 2. At starting frictional force of belt (loaded with material) and belt support plate will be high, and once belt start moving static co-efficient of frication will decrease to kinematic co-efficient friction. 3. Now, motor capacity should be cable to accelerate the belt from its static friction because we started the motor at zero velocity. 4. Friction between roller and belt is different than friction between belt support and belt, our aim should be increasing the friction between roller and belt for no slip. whereas our aim should be drecrece the friction between belt and belt suport, for easy pulling the belt, 5. Now, bearing friction is something that we should not consider in any calculation, you can consider as zero friction (in general) 6. So, for motor selection, these are following load you should consider. A. Frictional pull force between belt with load and belt support, B. Belt rolling friction (or you can say belt rolling resistance or belt drag over the rollers) -Which is actually difficult to calculate. C. MOI of all the rollers, gear box, motor and the load over the belt.
@joaogarcia9855
5 ай бұрын
@@mastermechanicaldesign Awesome! It makes sense for me now. I don’t know how to thank you enough for the time and response! Once more, congrats for the content and commitment! You’ve got a subscriber for sure :)
@g4ur4v88
4 ай бұрын
The video is great but check calculations do not match with the calculator
@alperenylmaz345
2 ай бұрын
7:27 frictional force is calculated wrong. It is twice of the value that you should calculated
@saravanatr7062
4 ай бұрын
Belt mass 2*5=10,2*0.5=1 total 11kg only. how it will come 11.5kg
@badrul6gamba662
4 ай бұрын
Please reconsider moi of roller it should be 1/2 Mr2.....
@narayandivekar8
12 күн бұрын
Excellent Explanation dude!! Keep it up
@Newonyou
3 ай бұрын
For some calculated power for an mechanical application, can we selecte AC induction motor or Bldc motor..? Or both for same power requirement?
@mastermechanicaldesign
3 ай бұрын
Yes power required will be same for all types of motors
@shanmugapriyana2419
Жыл бұрын
The frictional force is 807.36N , but the value is 1614.7 , we have to double it ?
@mastermechanicaldesign
Жыл бұрын
No, It's just trying mistakes, I don't know how to overcome typing mistakes, i really need a team to cross check. I'm the only one who does everything. And mistakes happens
@ronaksoni8425
Жыл бұрын
Thanks for giving calculations for Conveyor Belt Power.. I want to suggest that kindly make a video about Selection of Power Transmission Belt Drive or No. of belt.. in which Counter pulley System.
@mastermechanicaldesign
Жыл бұрын
Noted, I would be better to do this within a transmission design series
@samithdulina6716
9 ай бұрын
sir, how did you select MOI for gearbox from catalogue? its not clear. and also when selscting a motor, why did you select from "4P 1500min-1" catagory?
@mastermechanicaldesign
9 ай бұрын
For motor selection start from 18:02 Gearbox MOI - Find J value in catalogue 16:25
@navneetgoswami9121
11 ай бұрын
you are awesome man
@mastermechanicaldesign
11 ай бұрын
You too. Thank you 😊
@swapnilawalekar334
9 ай бұрын
Dear sir moi torque roller -0.25*15*(0.0225)2*2 value 0.0018 not available. Valve comes to 0.0037 please State whether this answer is correct or not
@mastermechanicaldesign
9 ай бұрын
Hi Swapnil, Yes there is few calculation mistyping in my video. So Your calculation should be correct 👍
@monikashinde6820
Ай бұрын
Very good explanation.....Thank you so much ...find it vey useful....Can you please make a video on Moment of inertia?
@mastermechanicaldesign
Ай бұрын
Will try
@aliff6893
2 ай бұрын
how to have its transfer function?
@SandeepKumar-il9hr
8 ай бұрын
Please make video on Moment of inertia
@mastermechanicaldesign
8 ай бұрын
Noted !!
@michaelmcphee4732
Ай бұрын
Your work is fantastic. At the 7.29 mark, you show Friction force = 1614.7 N I calculated 806.54? What did I miss please
@mastermechanicaldesign
Ай бұрын
There are some mathematical calculation mistakes from my side
@jugnu361
5 ай бұрын
If u remove the belt support Whete will u keep the Loan ? In Air ??
@mastermechanicaldesign
5 ай бұрын
No. Load will remain over the belt. Conveyor without belt support - Yes for short distance and light weight material transfer like plastic parts we don't give support below the belt. But this is not the main purpose of this video with this example I just want to say. If you don't support the belt then it doesn't mean that required torque will become zero. There will be a MOI of rollers and other items. "Watch the entire video otherwise you will be confused, I'm not confused"
@atishbijai1817
8 ай бұрын
Please make a video of shaft deaign, and also give the information about allowable shear tensile streess and strength and allowable bending moment and fatigue failure and what will be the safe value from protecting above point
@mastermechanicaldesign
8 ай бұрын
Noted Atish,
@seiftamazerti4547
Ай бұрын
@5:03 the unit i_s meter, not mm
@bharathrm5899
Жыл бұрын
Good information and much appreciated your efforts but kindly recheck the considerations for calculations as they seem little offset from actuals, as there is no much difference for the motor KW but when it comes to judge what can be done with other parameters to decide some intermittent operations that you get across while introducing other process based on selecting rpm’s and force flow process, might mislead to wrong assumptions though. All the way nicely explained
@mastermechanicaldesign
Жыл бұрын
Hi Bharathrm, Thank you so much. yes, there is little calculations typing errors with example. But concept and formulas are right. Just bear with me. mistyping will eliminate completely with time. trying to build a cross check community.
@saravanatr7062
4 ай бұрын
Thank you sharing the knowledge
@Newonyou
3 ай бұрын
Can you make a video to design a motorised trolley which is moving on wheel and rail track, with loading capacity of 40 ton. For given speed 20m/min, calculate gearbox, wheel dia, motor power, ?
@mastermechanicaldesign
3 ай бұрын
Yeah sure
@Newonyou
3 ай бұрын
Yes waiting for this video.
@Fenil_Faldu
Жыл бұрын
Need detail video regarding welding types , bearing selection and type gear and pully teeth calculation all those topics in separate detail video
@mastermechanicaldesign
Жыл бұрын
Sure 👍
@cadones3320
Жыл бұрын
Great sir make such videos regards mechanical design selection, calculation, Power train, gear ,shaft , pulley,motor selection etc
@mastermechanicaldesign
Жыл бұрын
Sure 😊, thank you so
@balajielango5383
18 күн бұрын
Excellent 👏
@Elektron318
Ай бұрын
Good explanation, which book you followed for these concepts?
@mastermechanicaldesign
Ай бұрын
there are no such books, I do study from manufacture detailed datasheets or research papers
@ManivannanK-kf5ee
Жыл бұрын
Make a video on leak testing fixture pneumatic cylinder selection
@mastermechanicaldesign
Жыл бұрын
Noted, Manivannan 😊
@vivekmagar7776
3 ай бұрын
In belt mass = volume*density but in video u take it area Unit of density is kg/m3
@mastermechanicaldesign
3 ай бұрын
Yes you are right, but i this equation i have considered Area density (For thin sheets, like paper or belts we consider area density. Not volumetric density. Excuse me for confusion.
@bringyoureyes2980
Жыл бұрын
Sir put video make for material selection of product design
@mastermechanicaldesign
Жыл бұрын
Sure, Noted. My notebook has been full 🤭
@errahulvats91
23 күн бұрын
At 7:26 how the pull force value calculated..? (Pull Force = 1614.7Newton as per your calculation in video) Total Mass is 411.5kg, g = 9.81m/sec sq. COF is 0.2 Pull force = COF x Total Mass x Gravity Constant >> 0.2x411.5x9.81 ==>> 807.363. (according to my calculation) Please correct me if i am missing something.
@selvasenthil1997
18 күн бұрын
Same doubt bro.....Got any solution for this??? Also at 15:35 MOI for 2 rollers = 0.25x15x(0.0225)^2x2 = 0.0038 kg/m^2 might come, but I guess wrongly mentioned as 0.0018 kg/m^2....Correct me also....I am also having the doubts.......
@errahulvats91
18 күн бұрын
@@selvasenthil1997 Yes. Method is OK just correct the calculations.
@engineeringfundamentals6958
8 ай бұрын
Powered roller chain conveyor calculation par video banaye.
@mastermechanicaldesign
8 ай бұрын
Let me first finish this bearing calculation series. Also i have used a powered roller only once in my experience. So it will take some time to research. I hope you understand me.
@SrinivasanSeenu-bk8jw
9 ай бұрын
hi sir, in the 20:26 second final velocity u gave 146.5 mm/sec but u didnt mentioned how it came there can u please explain it to me, Thanks for sharing the great video as usual awesome great content
@mastermechanicaldesign
9 ай бұрын
Its selected motor final speed- watch from 19:50 You welcome Srinivasan
@SrinivasanSeenu-bk8jw
9 ай бұрын
@@mastermechanicaldesign Thanks a lot sir😍
@vikaskumar-vi1pd
3 ай бұрын
All design understand but motor calculation not understand.
@mastermechanicaldesign
3 ай бұрын
Which calculation of motor ? Load or speed or torque ?
@ندىسلامة-و6ث
8 ай бұрын
how the convyeor belt density equal 2.3kg/m^2 the density equal kg/m^3
@mastermechanicaldesign
8 ай бұрын
Hi, The table which i referred to for belt density. There is belt "area density" kg/m2 defined. means mass of unit area of belt. For different thicknesses of the belt, So to calculate the mass of belt, we multiply the total area with unit area mass density.
@ندىسلامة-و6ث
8 ай бұрын
@@mastermechanicaldesign thank you❤
@Arfankhairularrasyid
3 ай бұрын
Thanks master,how to calculate chain conveyor
@mastermechanicaldesign
3 ай бұрын
I will make video on it, for sure
@Fenil_Faldu
Жыл бұрын
Please tell us indepth about welding symbols its types and methods
@mastermechanicaldesign
Жыл бұрын
Sure Fenil, noted. In content list
@vikramchoudhary4871
3 ай бұрын
COULD U PLEASE LET ME KNOW HOW TO CHOOSE MOTOR FOR Z OR INCLINE CONVEYOR.
@mastermechanicaldesign
2 ай бұрын
Yes, pull force become Pull force X cos A . (A - inclination angle)
@gauravyeolekar3231
2 ай бұрын
please make video on how to design slat conveyor.
@mastermechanicaldesign
2 ай бұрын
Noted
@avjart7748
3 ай бұрын
Sir please make a video on moment of inertia in detail and how to use it in design.
@mastermechanicaldesign
3 ай бұрын
Sure I will
@Ajinkya-16
3 ай бұрын
Thanks for Such wonderful knowledge. Sorry for this question. Have you started earning from this channel on KZitem? Asking because I am planning to do same. Asking for genuine advice
@mastermechanicaldesign
3 ай бұрын
You welcome, yes, this channel has been start earning since Nov 2023. with CMP around 5-6 USD. Genuine Advice- Yes, Doing KZitem is worth it in many ways, if you are doing it in the right way.
@Ajinkya-16
3 ай бұрын
@@mastermechanicaldesign thank you very much for your advice. Reading your reply actually gives me goosebumps. I asked multiple peoples but no one clearly tells. Thanks you very much
@magnusindia1577
3 ай бұрын
Sir, I know these calculations are for educational purposes only, but still the calculation for frictional force is wrong, I mean in your calculations it directly shows double value. I have tried it my end but the final result the comes to around 0.5 HP of Motor. Please clarify. or is any other value added to the mass x gravity value. I am talking about the calculation on 7:30 time. Please help.
@mastermechanicaldesign
3 ай бұрын
Hey, I very sorry for your Difficulties, yes there are some typo mistakes, please consider whatever your calculation is saying, solo motive of making of this video is to give you complete guideline, calculations steps and formula, and its expiations but unfortunately, there are some typo mistakes in example calculations.
@magnusindia1577
3 ай бұрын
@@mastermechanicaldesign Thank you for your response. Your video has helped me a lot to clear many doubts.
@nikhilsuwarnkar412
4 ай бұрын
Sir trunnion ball valve design calculation
@mastermechanicaldesign
4 ай бұрын
I can't help with this. I don't have experience in valve design.
@vipulbhalerao1982
2 ай бұрын
Plz share topic movement of inertia
@mastermechanicaldesign
2 ай бұрын
Sure!!
@automationguy9760
8 ай бұрын
How to select the motor for driven purpose of a machine from one place to another can you able to prepare a video for that
@mastermechanicaldesign
8 ай бұрын
How do you want to drive.. Like on wheels or pick and drop. I mean I'm not fully understanding your requirement
@automationguy9760
8 ай бұрын
Can you able to share your WhatsApp num so that I can share the image of that machine so you can easily understand
@tzb05
9 ай бұрын
I appreciate your help in providing me a brief equation or rule of thumb to calculate the specific energy consumption as Kwh/Mt/Km length = 5 Km , Flow = 2500 to 3000 Mt/Hr , Route inclination= zero inclination, Width = 1200 mm , trough angle=30 how much electricity will be consumed in electrical motor
@mastermechanicaldesign
9 ай бұрын
HI, Its very simple, 1. power consummation is equal to your conveyor motor required power. 2. 1 unit electricity is equal to 1 kW per hour. Let say your conveyor required motor power is 2 kW. Means your electricity consumption is 2 kW per hour means 2 Unit. -- for motor power calculation, refer formula of this video.
@tzb05
9 ай бұрын
@@mastermechanicaldesign the installed power is not the consumed power
@mastermechanicaldesign
9 ай бұрын
Yes, as i said, power consumption is equal to the required power to operate the conveyor (point 1)
@sambathbunkh
8 ай бұрын
Best explanation video
@vivekmagar7776
3 ай бұрын
What if incline conveyor ????
@mastermechanicaldesign
3 ай бұрын
In incline conveyor, belt pull force will increase, multiply with cos A
@DFazio-t8m
4 ай бұрын
I would clarify the no friction part. I think what you were saying was the first part was the load to move the belt and load at constant speed then the second part was to start the belt from rest to the set speed which would require the diameter of the rollers. Is this correct?
@mastermechanicaldesign
4 ай бұрын
Yes that's what I'm trying to say.. when we will start the conveyor from rest. An extra torque will be required to move the belt because of MOI of everything.
@DFazio-t8m
4 ай бұрын
@@mastermechanicaldesign thanks helps ALOT to know the nuance and can tackle other issues like if it was at an incline.
@cesarbeltran6353
10 ай бұрын
Is the diameter of the roller according to the motor or is it the design for the belt?
@mastermechanicaldesign
10 ай бұрын
According to me, diameter of roller should be according to belt thickness and belt material, like allowable minimum bending radius of belt top of that we should keep the roller diameter minimum just to keep MOI of rollers minimum also to save cost
@cesarbeltran6353
10 ай бұрын
@@mastermechanicaldesign it depends on the length of the belt too? for example I am designing a 10 meters belt with the same material you used in the video, how much diameter do you recommend to use for the roller?
Пікірлер: 295