My maxima has a standard transmission too. Kelsey shifts like a pro. I love driving my maxima but I have to do the motor mount fix this spring. Ain't gonna lie. Little nervous about the welding and fit. I'm good with mig but all I have is a flux core. Guess I'm going to learn because I love my low mileage maxima. All leather, heated seats, sun roof, Bose system is perfect everything works and runs quick, fast and smooth. Just the motor mount rust thing is the only problem. Thanks for your video on the support fix.
@bryanmurphy26
2 жыл бұрын
Thanks for checking in Mark. Good luck with your support repair.
@snowfall1771
3 жыл бұрын
Did she get alignment after wards
@boogiejonz
2 жыл бұрын
"Her ball joints and bushings are all sloppy..." LOL!
@rodboijones7390
5 жыл бұрын
Good video I have to do this same job. I'm glad to see that you don't have to remove those 3 bolts in the middle of the control arm like I saw someone else do.
@bryanmurphy26
5 жыл бұрын
Thanks. We just got some new coil-overs for her car today too. So it should really drive nice once we replace these worn out 17 year old struts.
@rodboijones7390
5 жыл бұрын
@@bryanmurphy26 Kool I just have one question like what size is the large bolt on the front of the control arm, and is it necessary to remove the three other bolts near the bushing or just that one large one?
@bryanmurphy26
5 жыл бұрын
@@rodboijones7390 I didnt have to remove the other 3 bolts. The big nut that holds the front control arm bushing was a 27 mm.
@rodboijones7390
5 жыл бұрын
@@bryanmurphy26 thanks man!
@ghost-4778
5 жыл бұрын
you and your wife look good working together she funny but you are funny too, that's great more content, also i have a 2003 nissan maxima 6 speed, i would love to see more content on your wife maxima, i use to live in htfd ct but now i live in florida, i'll take some photo of my car hopefully soon so you can see is gray on the outside and gray leather inside lol...
@bryanmurphy26
5 жыл бұрын
Kelsey told me today that she has $1000 that she wants to put into her car. I think we'll be doing some cool stuff to the maxima very soon. Probably starting with some suspension upgrades. Do you have anything done to yours yet?
@ghost-4778
5 жыл бұрын
i just order adjustables coilovers and rotors, i have few stuff that i have for a while, I want to have everything that i want before i install it, i have a whole list and parts for my car i'm just waiting for the right time and money lol...once i start installing i'll send you videos if that's ok with you.... that's awesome cool.
@rigoaparicio9929
3 жыл бұрын
After changing both of my lower control arm ,my drives side one is grinding (touching)my break rotor when making a left U turn....my passenger side is good....what did i do wrong and how can in fix
@Kaijuvq
2 жыл бұрын
Exactly what my 99 is doing and every shop keeps telling me discontinued back in 09. Got aome moog brands bc mi e is an se-limited but didn't know they all may differ or not any Info is helpful. Mine opposite driver good passenger hitting the cv drum.
@noureddineelaroussi7680
5 жыл бұрын
I see that you're using the wrong nut socket for the impact driver, they will go bad quick, you should get the black thick nuts from OEM or Husky!
@NickellessCageless
Күн бұрын
My machine doesn't have the wife😢
@Anthony11qq
3 жыл бұрын
I hate when my girl is even in the same state when l work on cars let alone talking in the garage. You're a better man then me. Good video tho...😂
@bryanmurphy26
3 жыл бұрын
She's my whole camera crew. She usually brings the hype too.
@michaelcurry2000
2 жыл бұрын
Easy when you know how 😁
@kabibnurmagomedov197
Жыл бұрын
Nice and tight always feel better if yk yk 🤣
@shermhart7617
4 жыл бұрын
What year model this one? I have 05 needing to replace, great vid
@bryanmurphy26
4 жыл бұрын
This was an 01, but the front control arms are very similar in design on the 05. Have a look at these. rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F283470166479
@tinhatrancher904
3 жыл бұрын
Do you think Moog makes a good control arms for the Max?
@Kaijuvq
2 жыл бұрын
No grease?
@snowfall1771
3 жыл бұрын
What part# was this
@sbond1963
4 жыл бұрын
Nissans chronically leak PS fluid, eating up bushings on pass side. You can see it all over the control arm
@sbond1963
4 жыл бұрын
Did you torque the axle bearing nut? Wondering what it should be
@bryanmurphy26
4 жыл бұрын
I didn't use a torque wrench. But I just looked up the torque spec, and it says 217 ft. lbs. I usually throw some thread locker on there if the factory nut retainer cap no longer exists, which seems to be the case on a lot of old maximas.
@hiitsmartin
4 жыл бұрын
How are the control arm holding up given they're from Ebay?
@bryanmurphy26
4 жыл бұрын
So far so good. I've used them in the past. They held up for 5 years on my maxima before I sold it.
@asaenzm2009able
5 жыл бұрын
Pinchi meco el cv joint no se quita.
@TheUltimate65
5 жыл бұрын
I never remove the driveaxle too lose the bolljoint..
@bryanmurphy26
5 жыл бұрын
I just did it so I could use that puller.
@TheUltimate65
5 жыл бұрын
I have om all years use Hammer of the side of bolljoint, if that help varm it up litle
@bryanmurphy26
5 жыл бұрын
@@TheUltimate65 I'll have to give that a try next time.
@juangonzalez2457
4 жыл бұрын
Don't you have too torque or fully tightened the bolts down when the car is on a level floor with the wheels on? Just curious I seen people do it either way.
@bryanmurphy26
4 жыл бұрын
Good point. I'd say it would be good practice for the front bushing to be close to the center of its operating range before its fully tightened. The rear one, it probably doesn't matter.
@juangonzalez2457
4 жыл бұрын
@@bryanmurphy26 Oh okay then.. Can I just use a car Jack to lift the rotor up to the center and tight it instead of putting on the tire and doing it on a level surface?
@bryanmurphy26
4 жыл бұрын
@@juangonzalez2457 Yes. That's the easiest way.👍
@juangonzalez2457
4 жыл бұрын
@@bryanmurphy26 For sure man thanks for the help!! Keep posting videos they are very entertaining and educational!
@bryanmurphy26
4 жыл бұрын
@@juangonzalez2457 We will. Thanks for the support!
@nicksacco2168
6 жыл бұрын
Hi Bryan I was wondering are you out of Connecticut because I wanted to know where there is some good shops that do tunes
@bryanmurphy26
6 жыл бұрын
Yes, I'm in Connecticut. I've been going to Dave's Tuning in Waterbury and Performance & Style in Manchester. I've also heard great things about Marsh Tuning in Wallingford. A few good options around the state.
@nicksacco2168
6 жыл бұрын
@@bryanmurphy26 Ok thank you
@nicksacco2168
6 жыл бұрын
@@bryanmurphy26 I'm not working with the type of cars I see I. The videos u post. I have a Hyundai sonata and it's not the turbo version. I'm looking to make a sleeper
@bryanmurphy26
6 жыл бұрын
If you're looking to fab up a turbo kit, you might want to try Performance & Style.
@monijewelljewell6267
4 жыл бұрын
Hi,Are you going to put an anti-sway and a upper strut bars?
@ghost-4778
5 жыл бұрын
hey guys what happen to the miata?
@bryanmurphy26
5 жыл бұрын
You'll be seeing it again soon. I think the ECU crapped out again. I have a new Adaptronic ECU arriving this Friday.
@ghost-4778
5 жыл бұрын
yes i remember you try to use the old one and you combine it with some part
@bryanmurphy26
5 жыл бұрын
@@ghost-4778 Yes, it worked properly for a year, then it started acting up again recently. So I ordered a new one.
@johnmartinez4309
4 жыл бұрын
teach kelsey how to hit them gears in that max!
@bryanmurphy26
4 жыл бұрын
She'll be driving my Z all week this week while I get her car ready to pass emissions. She already texted me 25 minutes into her first drive with the Z, telling me she needs more power in the maxima now.
@johnmartinez4309
4 жыл бұрын
@@bryanmurphy26 hahaha too funny. two questions.. any minor mods on the maxima? which Z you own 350 370?
@bryanmurphy26
4 жыл бұрын
@@johnmartinez4309 My Z isa a 350. Kelsey's Maxima has all the basic bolt-ons. Long tube headers, y pipe, high flow cat, megan catback, intake, clutch/ lightweight flywheel, coilovers, underdrive pulley, short throw shifter..
@johnmartinez4309
4 жыл бұрын
@@bryanmurphy26 nice you gotta throw some NWP thermal spacers on the VQ it works wonders and keeps the engine at much cooler temps. also you can add a NWP block off plate to gain more power in the higher rpms. bump the timing 2 degrees and i think she will be very satisfied with her final mods. She will be smashing 350z's and G35's no problem just from my experience tho.
@bryanmurphy26
4 жыл бұрын
@@johnmartinez4309 Good call. Maybe we can squeeze a little more out of it.
@caldwellguy
5 жыл бұрын
Your wife is pretty... Is she single?
@bryanmurphy26
5 жыл бұрын
Lol, I'm stealing that one😂
@kcoren2075
4 жыл бұрын
Very good video, but the none use of personal protective equipment is disturbing.
@bryanmurphy26
4 жыл бұрын
If you like safety, skip to 4:50 on this video. kzitem.info/news/bejne/0Gx41GyIh4qQg5w
Пікірлер: 72