Outstanding instructions, I changed out the gearbox in my washer today. Works perfectly. 😊
@bernardopadilla1842
4 ай бұрын
I would only change the sequence of the splutch and actuator to avoid any stress on the actuator arm, other than that, it is a great video with lots of usable information, congratulations and thank you for sharing.
@captainbeyond4350
Жыл бұрын
It's only three years old and you have to do a bearing replacement, that's messed up
@scrapman502
2 жыл бұрын
The washers with the large nut holding down the drum instead of the plastic clip are a different story. The agitator plate has a pot metal center in a plastic plate and it's mounted on a steel shaft of the gearbox. I have yet to come across an agitator plate that comes off without resistance. I've seen people use 2x4's and a hydraulic jack pressed up against the bolt to remove them. I sometimes have to beat the transmission shaft down with a length of 2x4 with a metal plate screwed to it as a makeshift sledge hammer while pulling up on the drum to release the transmission.(after un-bolting it first). The "bearing seal" on the shaft on some washers is made of metal with a rubber coating on it press fit to the shaft. It always gets stuck inside the drum. It's nearly impossible to get it out without cutting it out or splitting it with a chisel. The new transmission comes with one on it, so the old one HAS TO come out. re-assembly is never a problem. On complaints with this model of severe shaking, I have found that there are a lot of pennies and dimes that have slipped past the wash plate and get stuck in the drain holes in the drum. Removal of the drum is necessary to remove the coins.
@johnnyrubio4141
2 жыл бұрын
Exelente esplicacion
@elye3701
Жыл бұрын
Thanks. Good stuff. Kinda wondering why there are mixed imperial and metric screws/nuts.
@khalilhassni3663
3 жыл бұрын
Good job man with the best wishes
@Appliancevideo
3 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@exarkunn69
3 жыл бұрын
This video helped me fix mine, thanks!
@Appliancevideo
3 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@bulldogsandlife
3 жыл бұрын
Thank you so very much for this awesome video! Helped me out so so much
@Appliancevideo
3 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@jeffwilson4972
2 жыл бұрын
Thanks for this video!
@ChaoticStep
5 жыл бұрын
So mine only makes a grinding noise on agitation. Not during the spin. Any chance, could my issue be the same? Update: so I found a nut that came loose on the big pulley that connects to the main shaft through the tub. All I did was tighten it and the noise stopped. Hope that helps!
@Appliancevideo
5 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 6-days A week Monday -Saturday, or search at www.SaveMoreOnParts.com 24 hours 7- days A week.
@lloydgmail
4 жыл бұрын
I think mine does the same thing. Do you know the issue? I've replaced the gearbox in the past, wondering if I'd have to do it again.
@realtorromeo
3 жыл бұрын
Hello. Is it necessary to take the tub/basket out? Why? Also, a new gear case comes with seal right?
@billro6665
3 жыл бұрын
Did you watch the video ??????
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@troyleong7412
5 жыл бұрын
Great video.....but there's no way I could do this fix. I'd have to have a picture of each step.....so I could transfer everything back over. Cheers to you for being able to do this. ;)
@Appliancevideo
5 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@alexhatcher8812
5 жыл бұрын
Could you tear down the gear box and show where the damage actual is? The details directions for swapping the parts is excellent. be really helpful if we could see what is costing that much money!
@Appliancevideo
5 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Sunday, or search at www.SaveMoreOnParts.com 24 hours 7- days A week.
@JaleelJohanson62
3 жыл бұрын
It's so expensive because they've got it and you need it and nobody else can supply it....
@austinbrown8936
3 жыл бұрын
My problem was separating the transmission from the tub .
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@carlthornton3076
Жыл бұрын
Very Good!... #38 ✝ {11-9-2022}
@ScantPear
5 жыл бұрын
I have the kenmore version of that washer
@Appliancevideo
5 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@vond7495
4 жыл бұрын
Two questions.....1) How do you recalibrate a newer model Maytag MVWX700XL2, after replacing the actuator (It shows the error codes on a digital screen). I can't seem to find instructions to recalibrate a newer Maytag after a repair. 2) I've done everything to remove my Maytag Bravos XL washer pulsator (some call it a washer plate)...it won't budge. It raises up about 1/2 inch and seems to hit something, like it's locked in place. I want to check for coins that may be stuck underneath. I don't know what else to try. I tried turning it from side to side, as if it's washing, but it won't move back & forth either.....not sure if that's possible with the power off. What could be the problem ??
@Appliancevideo
4 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Saturday, or search at --www.SaveMoreOnParts.com-- 24 hours 7- days A week.
@terencetaylor9319
Жыл бұрын
What plastic clip? Your head was in the way the whole time.
@minza1989
5 жыл бұрын
Mine isn't making the same sound when spinning it manually but there is a little bit of water coming out and it when it is going on its own it sound like plastic spinning could this be the same thing that I need to do?
@Appliancevideo
5 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Sunday, or search at www.SaveMoreOnParts.com 24 hours 7- days A week.
@pauldow1648
4 жыл бұрын
So how much is gear box $ ?
@Appliancevideo
4 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Saturday, or search at www.SaveMoreOnParts.com 24 hours 7- days A week.
@Tonyinmemphis
4 жыл бұрын
The reason this happens is using too much soap And not cleaning the soap resin due to more than 1 tablespoon of soap. or 1/2 shotglass of soap.
@Appliancevideo
4 жыл бұрын
Hello Thanks for the good tip, I hope it can help others with the same issues. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page
@valwilliams3590
2 жыл бұрын
it would of been nice to actually see the bad part, how do we know it needed that whole thing ? maybe it just needed a bearing or plate or like the guy down below a nut came loose. OVER CHARGE I call it !
@bobbyphillips6596
2 жыл бұрын
I just replaced mine. Unfortunately, for this particular model, the bearing is sealed inside the transmission and is not serviceable. Other washers have accessible tub bearings, this one doesn't :(.
Пікірлер: 43