The diffs can be probablamatic as well , where the cv shaft splines into the gearbox check for a lot of play passenger side mainly , you have to poke your fi gears in there to feel it doesn't seam to effect the side of intermediate shaft .
@itsonlyGemini
Жыл бұрын
Hey man I have like a warping high pitch sound at low rpms in all gears an a grinding sound in gear box I’m guessing cause it sounds similar to the sound of a swift gearbox an both sounds disappear when I push clutch in so I’m guessing thrust bearing is okay could be a diff or gear box problem an I deffs need to upgrade the mounts, btw this helps a lot
@mrxakadan2357
5 жыл бұрын
Great car. Have a 2009 MPS BL would highly recommend upgrading to a trilogy set of mounts. Have the dammond set TMM, PMM & RMM in mine and works a treat. Very vibey but it's a sports car and fixed the bursting issues of the stock mounts. First mod I did on both the BL after my BK gen 1 broke it's stock PMM didn't want to replace with stock. Lesson learnt replace those mounts people!
@jonathanleclerc5923
5 жыл бұрын
I'm getting a Dammond RMM anytime soon, it will sure make the ride better
@hanseoul-oh496
2 жыл бұрын
Hi Can you help me to assemble valve body Mazda 3 type 9 2018?
@mikef058
5 жыл бұрын
Brett, this is not related to the video but is there a way to test the pcv valve on the Mazdaspeed 2.3 turbo motors? (Just trying to see if its clogged) I was doing some research and the Volvo guys do this glove test but not sure if this applies to all cars.
@CornerOfTheOval
4 жыл бұрын
Super good knowledge here, thanks for the vid
@claudev.k2
5 жыл бұрын
Hi, what kind of oil do you use for the MPS gearbox? I'm drinving a BK 2007 and want to replace the oil. In german MPS forums many people mentioned noise from and wear on the limited slip differential, when they did not use the Mazda standard oil, because this one has a special additive for the LSD.
@thanos3mazdaspeed
4 жыл бұрын
Redline MT 90
@eugenerayners9883
3 жыл бұрын
I have a noise when car is in neutral. I am sure it's coming from the gearbox. Could it be the input shaft bearing that went?
@fatho8852
3 жыл бұрын
the sound is probably normal unless it recently showed up or starting getting worse. My mazdaspeed always had a noticeable chatter at idle. way louder now that I have stiffer engine mounts but I just ignore it and it's never gotten worse or anything
@tenmillionvolts
4 жыл бұрын
Hi. I have an '07 Mazda3 MPS (gen 1) and the clutch goes soft after a 1st to 2nd hard rev and gear change. Clutch goes near floor and a couple of pumps fixes it. Had this problem for about 20,000km and forums suggest throw out bearing sticks on shaft. Is there a way to lube the shaft a little through the fork hole? Have you had this issue? Seems common as they age.
@bobsoft
3 жыл бұрын
clutch master cylinder
@joshbaca4805
4 жыл бұрын
I have a 2007 speed 3 I just recently broke my cv axle and now my car is making a crazy grinding sound .. could my transmission be messed up as well?
@SkidooGaming
3 жыл бұрын
my cv axle went aswell on my 09 3 , if you broke your inner cv you could be facing with stripped metal within, but i doubt that. you probably just have had a mass hole in your cv boot and now it’s grinding hard on turns or acceleration bumps etc. goodluck, i did mine myself for 100$ cad, literally 5 bolts
@vbrvideoproductions4643
3 жыл бұрын
anyone ever tried to replace the clutch mster cylinder on a first gen Mazda 3 (JDM) MPS right hand drive?
@thfreakinacage
4 жыл бұрын
Never seen that type of flywheel before, meant to smooth out gear changes etc. I'm just thinking "well just drive it properly" but it's still clever :P
Пікірлер: 19