I know you’re just showing the proper way that you should do it but honestly how many guys even put the vendor on the floor for a 30° offset or any offset for that matter other than a 90°? Most of my bending as an apprentice I’ve been taught to do in the air
@tragan1442
Жыл бұрын
Soon to be cw here thanks for the vid
@mohammedhassani3975
4 жыл бұрын
good job
@jakirsheikh2631
3 жыл бұрын
how need majarmant
@adams6798
Жыл бұрын
Great video but explain to people how multipliers are found using Trig?
@glennmann634
3 жыл бұрын
Great video. Thanks for posting. Nice looking bender. What brand is it? (Thanks in advance for the answer.)
@passionateengineer04
3 жыл бұрын
Sorry i didn't remember the brand.
@Bapuji42
Жыл бұрын
This doesn't show how to use shrinkage to calculate for a given distance between the end of the conduit and the beginning of the first bend.
@jarrisyed8372
3 жыл бұрын
hey viewed by me :D
@ryanb1874
4 жыл бұрын
Does the diameter of the conduit have anythi g to do with the "shrink" or is it all treated like a thin line?
@passionateengineer04
4 жыл бұрын
Consider it as thin line.
@mariamontolla5978
4 жыл бұрын
Ok!! How tje eff do you find the multiplier
@ryanb1874
4 жыл бұрын
The multiplier has to do with the angle, it's 30 degrees, sine of 30 = .5. But we are dividing by SINE 30, so it's like multiply by 2. Get the uglies manual.
@diazaa
3 жыл бұрын
45=1.414, 30=2, 15=3.86.... Those are the only ones I have memorized.
@lazarevic95
3 жыл бұрын
a way to find the multiplier for any bend angle is - 1/Sine(angle
@diazaa
2 жыл бұрын
@@lazarevic95 Hey now, dont give away these magical tricks of the trade!!!
@diazaa
3 жыл бұрын
Depending on bending angle you should put your mark on the tangent of the angle. In this scenario you can see that the mark is in front of the bend as it should be in the center of the bend. This is important if you need the bends to be in an exact location.
@AngelRomero955
2 жыл бұрын
How do I put at mark at 0.57735026919?
@diazaa
2 жыл бұрын
@@AngelRomero955 .57 degrees?
@AngelRomero955
2 жыл бұрын
I found in another video that when making parallel runs with offsets. You need/want to use the Tangent of the offset angle. So it checks out. I’m a 1st year apprentice I still haven’t done any fancy bends.
@diazaa
2 жыл бұрын
@@AngelRomero955ok but what was your question about marking at .57? I have alot of experience (10+yrs) measuring for, routing and bending hydraulic tubing.
@Bapuji42
Жыл бұрын
@@AngelRomero955 Huh? The distance between marks is 1/sin(angle) times the offset rise.
@patricktelfort
4 жыл бұрын
What video is This from?
@passionateengineer04
4 жыл бұрын
For conduit bending
@patricktelfort
4 жыл бұрын
The title of the actual video
@passionateengineer04
4 жыл бұрын
@@patricktelfort Multiplier method of offset bend
@jondyer4753
4 жыл бұрын
PASSIONATE ENGINEER Good video
@juancarlosarayamanriquez2850
3 жыл бұрын
Si hubiera subtitulado español sinvirioa
@alen2283
2 жыл бұрын
Its time to move on kopex like rest of the world!!
@FuquarProductions
9 ай бұрын
"pick a spot, bend it... then pick another spot, bent it... then you have nothing you're looking for. Thanks for not actually explaining what the multiplier is and how you find it.
@joseargumedo6389
2 жыл бұрын
Ahhh yes Vietnam
@akurukyo6217
2 жыл бұрын
You probably forgot to show the 1st and 2nd step which is ; preparing the necessary materials,tools,and equipment. And wearing ppe
Пікірлер: 36