Was really looking for a video on what to look for with injectors using a scan tool, but good anyway
@sadiagnostics
6 ай бұрын
Thanks for the feedback
@mayankhomagalasi7540
2 жыл бұрын
great!
@kevinpalmer7452
2 жыл бұрын
Always great content thanks 🙏
@sadiagnostics
2 жыл бұрын
Thank you 🙏
@tshedzanaledzana5479
Жыл бұрын
@@sadiagnostics i have the same problem with mu 2014 sprinter..i need ur service
@Arifali-wp2ze
Жыл бұрын
Love you sir
@amarimadani5296
2 жыл бұрын
Great video.So can MaxiSys Pro do component protection in VAG groups?
@sadiagnostics
2 жыл бұрын
They are not the best, your better buying live vcds.
@aqibfreed4672
8 ай бұрын
If you mix up injectors by mistake will they still code correctly ? If injectors have become mixed how does one find their correct allocation
@benjaminlevi7792
2 жыл бұрын
Good job
@sadiagnostics
2 жыл бұрын
Thank you
@zeljkomilos7244
2 жыл бұрын
Hi there thanks for the video I’m currently working on a sprinter 2017 mod 313 cdi We have replaced the worn timing chain as It jumped We put the engine back together in the correct timing used the same injectors bled air from the fuel lines but we cannot get the engine to start it keeps cranking but no start however when we spray Starting Agent into the intake the engine briefly starts and runs as long as you keep spraying the agent into the intake I have Autotel Mk 808 Scener ( can this unit perform injector re-coding ?). We checked and confirmed that diesel injectors are corresponding to correct cylinders on the scanner. Common rail fuel pressure reaches 300 bar when cranking there’s no more air in the fuel lines all four cylinders are returning just under 300 psi compression but it seems to be that there is no fuel coming past any of the diesel injectors can it be possible that all four injectors have seized up shut Engine has done 465,000 km and it’s not displaying any more codes..? Any suggestion would be greatly appreciated Thanks
@sadiagnostics
2 жыл бұрын
Hi sorry I can’t really say much it could be anything really, cam shaft sensor etc… do live data and see if anything is coming up
@93mrmm
Жыл бұрын
Hi did I have the same exact problem. Did u solved the problem ?? Thanks
@TheCyberkiller28
Жыл бұрын
@@93mrmm also have the same problem, can start it for 3 days, did you fix it maybe?
@simout3877
Жыл бұрын
Did you find out what’s wrong I have same issue thanks
@Gdljal24
Жыл бұрын
Hello there I hope this helps…I had this same issue we replaced the engine on a Sprinter 313 cdi due bent rod and of course we have to drain the fuel from the system we put everything back together as it should but didn’t wanted to start we found that the injectors got seized up shut we sent them to a shop to get them open and gave us instructions on how to bleed these Delphi injectors they’re pain in the rear but this how you bleed them when they’re completely dry 1st leave the injectors unplugged 2nd do not plug the return lines 3rd cycle the ignition about 5-6 times until there’s enough Diesel in the system 4th tighten the lines then lose them about 1/4 turn 5th have someone to crank the engine until you see Diesel pouring from the lose lines 6th close the lines 7th tell your buddy to crank the engine again until you see Diesel coming out of the injectors thru the return holes 8th plug the return lines 9th crank it again few times 10th plug the electrical connectors to the injectors, it should start Here is a video of these Injectors kzitem.info/news/bejne/wp6nqI19poZ9pXY
@edmilsonpinto4619
2 ай бұрын
If you use easy start spray it would start ???
@resadsubasic6788
2 жыл бұрын
👋
@user-lq4ki8kr7x
5 ай бұрын
BEAUTIFUL PLZ COUD YOU EXPLAIN WHAT IS THE DIFFERENCE BETWEEN CODING AND PROGRAMMING AS WELL AS SOFTWARE TO MOUDLE? THX REGARDS A LEARNER.
@edmilsonpinto4619
2 ай бұрын
Injectores job have been done on my Mercedes and the car crank but don’t start , saw your video and went to check , and saw that he put the injector code from injector number 3 on the on the injector 4 . Now I try to change but wasn’t working , the Maxine was failing to do the programming what is your advice ?? Thanks will help a lot My car is Mercedes E class 220 bluetec 2014
@edmilsonpinto4619
2 ай бұрын
Don’t know if was doing wrong way , the Maxine that I was using it calls Nukar
@joshuavargas9408
Жыл бұрын
Is it the same thing for 2013 mercedes cls550
@sadiagnostics
Жыл бұрын
No it’s different with Petrol cars…
@joshuavargas9408
Жыл бұрын
My car has a check engine light , fuel injector control module, a mechanic scan it and said some one replaced the injector and didn’t enter the values , he said they all say 0
@AhmedAli-hu8ng
2 жыл бұрын
Great information boss waht is name this I mean autel waht model and number
@sadiagnostics
2 жыл бұрын
Thanks it’s Autel Maxisys MS908s pro
@Arifali-wp2ze
Жыл бұрын
One video uploade redar
@tshedzanaledzana5479
7 ай бұрын
Hello sir..my sprinter has the same problem,can i get ur contact
@joshrulz8p
Жыл бұрын
does this apply to w638 vito ? have replaced 4x injectors - will not start on key but can roll start it and runs fine.
@sadiagnostics
Жыл бұрын
Yes all Mercedes are same.
@joshrulz8p
Жыл бұрын
@@sadiagnostics thanks for the reply, its weird that i can get it running from a roll start and it runs mint, just never starts under key
@sadiagnostics
Жыл бұрын
@@joshrulz8p yeh that’s like first I’ve heard but hopefully you’ll get it sorted.
@FrenchConnectie
Жыл бұрын
With my mk906 pro i could not get in to the engine... Didn't show a single hot function and kept saying it was a gasoline car while it's a diesel. I have send the computer back. What a waste!
@FrenchConnectie
Жыл бұрын
And why doesn't Autel send a user manual with the computer!!?? Unbelievable
Пікірлер: 39