great work, i did this today finally. Some pointers for others that try this: you need to release the parking brake otherwise it will popup an error when you try to open the brake cylinder via the menu system. The error reported is "Conditions not fulfilled. Retry with OK Cancel with Back". Once the parking brake is released you'll be fine. Another thing that caused me irritation was removing the electric connector (not the sensor) from each side, there's a clip holding it in place but it wasnt clear to me how to release it so I broke it on one side. Hopefully it wont cause me problems later, basically though it's held in with that clip and you need to push it up gently while pulling on the plug.
@HotFiya05
2 жыл бұрын
Was able to do this job in 2 hours on my ’19 w213. The hardest part were the brake mount pins. Those suckers were on tight from the factory. WISH I had a lift for ease of access.
@siavashheidari2872
2 жыл бұрын
Thank you sir , this is best I could find in you tube keep up good work.
@superspak
Жыл бұрын
Great video and nice to see the technology in some of these newer cars wrt servicing. I took a brake/suspension class way back in 2014 or so when I was a new engineer, and I had forgotten about how we had to put the EU spec Jeeps with the "lug bolts" instead of the "lug nuts", so alas mounting the wheel can be a bit iffy, but it looks like you got it down 😊
@germansupplycom
Жыл бұрын
Excellent video. One small improvement you could make is to note the location of the rubber composite brake pin. It is fitted to the lower position but you can't tell this in the video.
@autopflegeNRW24
2 жыл бұрын
danke,viel erfolg
@jozefkubasky8712
Жыл бұрын
Hi, what torque specs did you use in order to tighten the bolts?
@MrEddyz1
2 ай бұрын
What do those dots on the discs mean
@ncbrady
2 жыл бұрын
thanks for the video ! can you please share what the blue grease you used was called (ebay/amazon link ?) and the white spray you used ? thanks so much !
@siiNke
2 жыл бұрын
Thank you! Get some W177 and do every single part :D
@josephdibella752
2 жыл бұрын
What is the white spray you used?
@vladas7771
11 ай бұрын
Any precautions when lifting car with an air suspension ?
@DFCGarage
11 ай бұрын
This model nothing to do. Some cars have service mode.
@jgomez7822
2 жыл бұрын
So after you close your break fluid cap and you're done exit fitting position you don't need press the brake with your feet and pump the fluid. or is that what the exit fitting position is for?
@mercedes_and_more
Жыл бұрын
The brake fitting position mode frees off the e handbrake to ensure it doesn’t come on whilst you are changing the pads. You still need to manually push back the caliper (having removed the filler cap first). Once you have exited fitting mode then check the level and refit the cap. Brake pressure will return after the first press of the brake pedal 👍
@miadamov
2 жыл бұрын
Respect ! I'm interested in the crane with which you lift the car. specifications, name, (what voltage) and approximate price.
@DFCGarage
2 жыл бұрын
www.twinbusch.de/product_info.php?products_id=154
@aykay711
Жыл бұрын
When removing the brake rotor the tool used for that is T25 or T30?
@lamoorproduction550
Жыл бұрын
T30
@Bezpokraski
2 жыл бұрын
🔥🔥🔥👍👍👍👍
@jonahfuehring178
Жыл бұрын
Does anybody know all the sizes of the bolts used in this video?
@lamoorproduction550
Жыл бұрын
18 on Caliper, 13 on pins
@lamoorproduction550
Жыл бұрын
How long time did it take for your rotors to be completely uncoated?
@DFCGarage
Жыл бұрын
I didn’t pay attention to that ✌️
@lamoorproduction550
Жыл бұрын
@@DFCGarage i’m asking because I still have a line of coat in the middle of a brake disks, same on both sides. I drives like 100-150km after I change my rotors
@DFCGarage
Жыл бұрын
@@lamoorproduction550 Maybe the lines are from the small holes in the brake disks that help you to see when the disks are worn out.
@lamoorproduction550
Жыл бұрын
@@DFCGarage a line is like 5cm wide, that can be pad that maybe doesn’t pushing one hole disk, until new disk and new pads start to work with each other normally. I don’t know
@machargs123
Жыл бұрын
Ace
@osypky
2 жыл бұрын
What vaseline you use on pins :)
@DFCGarage
2 жыл бұрын
I have a mechanic shop nearby; a mechanic gave me that Vaseline special for the job. I did something wrong? 😅
@osypky
2 жыл бұрын
@@DFCGarage I ask for the type or product 😊
@DFCGarage
2 жыл бұрын
@@osypky is brake caliper slide pin grease, you have a link in the description with the product
Пікірлер: 34