Hello all please hit the like button comment and subscribe
@vincentseidle954
Жыл бұрын
Appreciate the videos! Love learning more
@cryptojohnny7781
6 ай бұрын
Doing this tomorrow ha ha , not looking forward to it. Damn thing keeps arching on the left side . Was going to just replace the stir blade but seeing as you have to remove the guide anyways I guess I ll replace it too , thanks for the vid
@mrfixit8806
2 ай бұрын
You dont have to remove the waveguides to change the stirrer blades
@cryptojohnny7781
2 ай бұрын
@@mrfixit8806ya did one but that plate on the underside inside the damn bolts snapped off ( bad design) been finding lots of arching on these machines lately as I do them all for Starbucks
@johnnydollars
11 ай бұрын
Awesome !!!
@xxxviii007
Жыл бұрын
Kline wire stripper/ stud remover looks expensive... lol appreciate the video man.
@mrfixit8806
9 ай бұрын
Yes there expensive stud removers but they work great
@vashlogoped_174
3 ай бұрын
Hello! Do you guys have video how to change magnetron on Merrychef. We often have 104 error and think of changing magnetron. Is it correct?
@mrfixit8806
Ай бұрын
@@vashlogoped_174 Im not sure if there is. Video on replacing the magnetron yet but it is very possible that a e104 is something else
@roopairs
Жыл бұрын
FIRE!!!!
@init4dawin
Жыл бұрын
What size are the screws to get the panel off smaller than 1/4… very small
@mrfixit8806
9 ай бұрын
5.5mm
@init4dawin
9 ай бұрын
@@mrfixit8806thanks
@gregorye6075
8 ай бұрын
Hi, thank you for very helpful service video. I have e3 merry chef from 2016 and I am kept getting megnatron overheat error e117. I checked current draw and it's 5.5amps max. I replaced temp sensor on the magnetron as it was cheapest option. Would you know what the current should be on a single magnetron unit?
@mrfixit8806
2 ай бұрын
Depends on how many mags you have but you should have a minimum of 7.5 per mag depending on voltage
@mrfixit8806
Ай бұрын
Sounds like a bad mag
@liaqautali3667
10 ай бұрын
Hi Error code E111.. cavity sensor.. Is there a rest button..?? Or does sensor need replacing?? Anythoughts ?? Tnx
@mrfixit8806
9 ай бұрын
Theres a hi limit for the cavity and on each magnetron See if it has continuity if it does then it’s good. The cavity hi limit can be reset
@liaqautali3667
9 ай бұрын
@@mrfixit8806 Thank you.. How do i go about in resetting the hi limit?
@mrfixit8806
8 күн бұрын
@@liaqautali3667you just reset the high limit
@jonnykelly5696
5 ай бұрын
Where are you based where do you cover
@mrfixit8806
2 ай бұрын
Southern California
@johnkane2000
10 ай бұрын
I’ve got an E4s that gives intermittent mag fail and Amps hesitate at 1.3-1.4 before going up to 7a. Could this be the capacitor or diode?
@mrfixit8806
9 ай бұрын
Could be magnetron or capacitor
@johnkane2000
9 ай бұрын
@@mrfixit8806 hey, thanks for the reply. It is very intermittent. We haven’t had an error in 4 wks and then non stop for days. Are their any cleaning procedures maybe we need to spy attention to?
@jarroddouglas8814
8 ай бұрын
A lot of times it depends on what’s being cooked I would check your 2 vents make sure it’s breathing
@mrfixit8806
Ай бұрын
@@johnkane2000 sounds like maybe a board issue but could be anything on the microwave circuit
@Cyborg20231
9 ай бұрын
Если E2S при включении в сеть циклическая перезагрузка и так по кругу. Что может быть? Заранее спасибо
@mrfixit8806
2 ай бұрын
Could just not be connected to the internet
@cryptojohnny7781
Жыл бұрын
If ever you need a job and in Canada give me a shout 👍.
@mrfixit8806
Жыл бұрын
Ty Im in So Cal
@mrfixit8806
9 ай бұрын
Thanks Im in Ca so i dont think that i could work in Canada legally Lol
Пікірлер: 36