Excellent video. One more thing that I think can help with some of the chatter: changing speeds. Sometimes with a certain setup, you get a specific frequency that likes to resonate. So if you change the speed, you might see the chatter diminish disproportionately. You just have to experiment with it to find out.
@bonnieadams9717
3 жыл бұрын
Just want to thank you for these videos and let you know that I have assigned many of them to my high school students to watch, I hope you don't mind. It's almost impossible to teach this online without a good video. Frankly, I think these are outstanding. So professional, to the point, you have a great presence on screen. Also, my cat and your cat look a lot alike not twins similar, mine is close to 19 years old and darker. She started out almost all white and has darkened up over the years.
@bbushong67
11 ай бұрын
I was hoping to see the same cut with the tail supported to see the difference from unsupported...
@westporter1
2 жыл бұрын
"Where that chicken comes home to roost" - Q.D., now added to my rolodex of sayings. Your videos are pure platinum. Thank you for excellent content.
@grahamking1381
5 жыл бұрын
Useful, concise, articulate, clear and straightforward. Excellent pedagogy. Thanks (and thanks to Abom79 for sending me here).
@Blondihacks
5 жыл бұрын
That’s very kind, thank you! Welcome to my channel!
@bdgackle
Жыл бұрын
The butter chatter demo is brilliant. Excellent way to visualize that, thank you.
@ALAPINO
Жыл бұрын
Oh, man. Chatter hurts my soul.
@hansenjantoft2587
Жыл бұрын
i start your program on youtube my dog lay down in my sofa , he know it will take its time. and when i start my baby lathe a C1 it take no time now to make a brass bearing for my old printer. im 67 and have been a book printer since 1975. in denmark . i dint think i could learn more, i can. thanks.
@KW-ei3pi
5 жыл бұрын
Quinn Thank you for explaining this. I have never heard an explanation other than lack of rigidity. This will help a lot in avoiding or eliminating chatter. Again, well explained, clear and understandable. Thank you!
@Blondihacks
5 жыл бұрын
Great! I'm glad the video helped. Thanks for watching!
@turiddu9
Жыл бұрын
Wow, your grasp of the material covered here, and more importantly your explanation of the concept is spot on! Great work and a wonderful approach to teaching these skills! Thank you!
@Uncleroger1225
3 жыл бұрын
I have just discovered your basic series and find your explanations excellent. Concise, understandable, and backed by accurate principals. I also enjoy the lack of "filler conversation" The humor you do add is enjoyable and direct. Good Job!
@mute8s
5 жыл бұрын
Well using the butter example I see two simple fixes. Either put your part in the microwave briefly or run your tool under hot water for a minute. Chatter eliminated! 😉
@Blondihacks
5 жыл бұрын
Haha, I’ll add those tips in a later video. 😁
@madmarty7103
3 жыл бұрын
in some cases you can increase the tool pressure so the tool is loaded with enough force and the "spring-effect" goes away. For me this worked very well with a thin long boring bar.
@HeyChickens
5 ай бұрын
Yes. Because you are cutting away a thick enough layer of metal that even the thinner layer is still not reaching the surface and creating a reduced friction moment that allows the work piece to accelerate.
@VIVA4EVER2001
4 жыл бұрын
Hi, just brilliant. Many thanks for sharing your amazing knowledge in a way that's easy to understand.
@pavelcurtis
5 жыл бұрын
Great as usual, Quinn! Though I was really hoping for the "relief" of getting to see you get rid of the chatter marks on that piece... :-)
@Blondihacks
5 жыл бұрын
Shoot, that would have been a great way to end the video. I wish I had thought of it!
@pavelcurtis
5 жыл бұрын
@@Blondihacks Obviously, you should be using me as a test audience during production... :-)
@northbetrue
4 жыл бұрын
I just bought a mini lathe, and I truly believe your videos have prevented all manner of personal injury. As soon as I get ink for my printer, I'm making a poster with a picture of you and "Don't Be Stupid" in a way too large font. Thank you, for the ideas, the pearls of knowledge and the laughs. That poster I mentioned will likely come out semi-good. You should make a good one and add it to your merch. I bet I'm not the only one who would like that hanging in the shop. Cheers from Boston Mass
@futten3230
5 жыл бұрын
i have a problem with a minilathe i get chatter when i face roundstock it has a spiral shapped pattern its a very low frequency sound so i usually have to put the speed at max which is 2500 rpm and take super small kits to get the ugly surface away and dosent matter how far the piece is stickin outa the chuck
@milithemuffin4534
5 жыл бұрын
If it doesn't matter how far away it's from the chuck i'd look at sliding surfaces (what's the contact area between them, is there any play and so on)
@JulianMakes
4 жыл бұрын
I really like your logical and well thought out explanations thanks
@shanedoyle1057
4 жыл бұрын
Ah can’t beat the kerrygold! Hello and thanks from Eire 👍
@ChristopherTate
5 жыл бұрын
It was an effort of will not to leap for a disengage at the "listen to this..." example. O.O
@Blondihacks
5 жыл бұрын
Hehe, I know the feeling.
@1elkym
3 жыл бұрын
Your pedagogy is excellent, your editing is fantastic, your audio quality is amazing, and your sense of humor is divine. Thank you.
@godiasdf
2 жыл бұрын
remember to set your tool at the right height, a tool that sits too high will grab and release, grab and release
@Ritalie
Жыл бұрын
2:54. The slow building of resonance. Nikola Tesla's "Earthquake machine" which apparently almost brought down an entire building by accident during testing.
@Makebuildmodify
5 жыл бұрын
Thank you!
@tonymonaghan5993
3 ай бұрын
Wow...these videos are so so good. Thank you so much. I've just bough a small Proxxon lathe and this is so informative. Thank you!!
@gregmacintyre3646
3 ай бұрын
Really like your video's, I am a beginner and your instructions have helped me a lot. I rebuilt an Old Craftsman 101 lathe and I know there is going to be some sloppiness, but I am still getting a rough finish. I have been experimenting with different tooling HSS, Carbide Inserts and Carbide tip and have noticed that at higher speeds the Inserts preform the worst even with swallow cuts of .001 to .003. I have been using tail stock support on all cuts but still getting that butter effect. Any suggestions on where the problem still might be? My 3-jaw chuck has a .003 run out.
@mickchaganis6607
3 жыл бұрын
I've just bought an old 1958 Lorche lathe, OK it's got a modern upgrade, 1 hp, 3 phase motor with infinate variable drive, I've scoured the Internet for tutorials and found you 😁 I just want to say thank you, your tutorials are brilliant, you put things across in an easy to understand way, this video is a prime example, I now fully understand chatter and am working my way through your tutorials while putting the finishing touches on restoring my lathe. Once again, thank you so much, I am a total newbe to the metal lathe and you are giving me the confidence and knowledge to start turning 💕
@glenn_r_frank_author
3 жыл бұрын
Everything is a spring... and this is where the chicken comes home to roost... so... Chatter is a Spring Chicken? :-)
@waltherstolzing9719
5 жыл бұрын
Wonderful -- but you could have picked cheaper butter, maybe? :P
@Blondihacks
5 жыл бұрын
Don't worry, it still got eaten. No butter goes to waste at Blondihacks.
@protocol6
5 ай бұрын
The hacker in me wonders if the harmonic issue might be something you could tackle from another direction. Namely, the ole' "walk without rhythm and it won't attract the worm" method. It works for beer, coffee, cat dishes full of water and soldiers crossing bridges, anyway. Hack an Arduino or something into the speed controller on the lathe and try to vary the the rotation speed randomly within a range around the setpoint. The variation would need to be smoothed heavily, I think. It probably wouldn't work and it might well cause other problems.
@edwardnikoliich5504
Жыл бұрын
How am I just NOW finding this channel?? Absolutely amazing collection of videos. Thanks for taking the time!!
@lenchodirker710
5 жыл бұрын
Very nicely explained...Thank you ! BTW Kerigold products are usually stored in the fridge. I'll try my toolbox instead to see if it prevents my teeth from chattering.
@Blondihacks
5 жыл бұрын
It certainly made my waistline chatter when I walk.
@vigwelding926
4 жыл бұрын
@Quinn - Always been fascinated with machinists lathe and have contemplated several times about purchasing one and was trying to learn some basics when I run across your channel. I have to say that I am impressed with your ability of explaining the operational basics of the metal lathe and how to use the tooling. I was curious how you like the Precision Matthews 1022V and if you were given the option, would you purchase it again? I had actually been looking at the Grizzly 602 but I seen a lot of people on the web talk about Precision Matthews lathes. Remember, I am new to all things lathe.
@JohnMcGrathManInShed
2 жыл бұрын
Can't beat Kerry Gold to be fair!
@jontypiper9881
Ай бұрын
Thanks so much for this, I'm new to the metal lathe and trying to just learn after using a wood lathe for around 4 years, so much to learn and this helps a lot!
@ClicheKHFan
Ай бұрын
That butter demo was really great, but I was kinda hoping to see you turn some cold butter.
@eddtube
4 жыл бұрын
Just found your channel - excellent way of describing things, straight to the point and interesting. Thanks!
@Blondihacks
4 жыл бұрын
Thank you for watching! 😁
@chazlabreck
Ай бұрын
Recently i was doing some lathe work and found if i ground the tool to cut towards the head-stock and less towards the work it didn't chatter.. good geometry of the tool seems to also help a lot.. rake angles etc , i think the perception is you go into the work at a 90 degree attack and het driving the cutting edge more towards the head-stock seems to work so much better for me
@Ilikerawfish
2 жыл бұрын
These are great tutorials. My grandfather has a lathe that is without use now. I watched him do beautiful pieces on that and I would really like to bring that machine to life again. Thanks for posting!
@bikewrecker1000
Жыл бұрын
Great video as always! I have a follow up question. You mention that to get rid of chatter, you have to take a cut that's deeper than the chatter marks, but a deeper cut would also increase your tool pressure which would make you more likely to experience chatter, right? So is the solution to increase rigidity elsewhere then take a deeper cut, or should you try to remove the chatter marks with an abrasive before continuing?
@thesmallengineguy4694
2 жыл бұрын
So clear and informative! Thank you for this video. I'm slowly learning how to use my old Sears lathe.
@richardowens9170
Жыл бұрын
Just found your lathe series for beginners. Very clear and well done you are a terrific teacher. Thanks so much for the time and effort you put into the endeavor. I have learned a lot!
@HorizonimagingCoUkPhotography
2 жыл бұрын
Ah yes I can now say confidently I’ve just experienced chatter on my mini mill 😄 Thanks for the clear, concise video - I know what to do about it now!
@dirtydug1831
5 жыл бұрын
Found your channel from Abom79. Do you have a background in Education? Writing? Your explanations are very clear and concise. Really easy to follow. Thanks for sharing
@Blondihacks
5 жыл бұрын
Thank you very much! I don't have a background in teaching, but it is something that I enjoy! Welcome to my channel and thanks for the sub!
@DadGrooves
2 жыл бұрын
I was just going to order some Kerrygold chatter; should I get the carbide or HSS version?
@yolofunk1367
3 жыл бұрын
Hey blonde can I merry you? So that I can learn more from I'm a machinist to,😁😁😁
@boogerzekesweldingemporium4833
3 жыл бұрын
Whew!! I thought I was the only one who kept butter in my tool drawers. Thanks for giving me a little validation Quinn.
@HeyChickens
5 ай бұрын
How am I the first one to like this comment after 2 years? Brilliant!
@brimhalljohn
3 жыл бұрын
I think you're brillant. Love the butter!
@can5projects563
5 жыл бұрын
great videos i love the way you explain all. nice and clear...... awesome..
@Garageaholic
3 жыл бұрын
Hahaha I have butter in my mill drawer too. What are the chances!?!?
@heliarcweldandmachine
5 жыл бұрын
the best butter in the world ! bake soda bread and enjoy ! and another good video. go raibh maith agat
@johnstrange6799
5 жыл бұрын
Good stuff, Quinn. Thanks.
@TaintedMojo
2 жыл бұрын
What, you guys don’t keep a pound of butter in your tool chest?
@JC-un4bg
Жыл бұрын
These videos are very easy to follow with a good cadence. Not to fast
@ArtBites
Ай бұрын
How do you clean/maintain a lathe?
@wihannieuwoudt8972
Жыл бұрын
Can the wrong speed (rpm) also cause chatter?
@4SafetyTraining
5 жыл бұрын
Always helps to use good butter.... great job.
@knitt9914
5 жыл бұрын
hey thanks, Im realy new to this topic, recently I use round nose HSS tool with aggressive cut, you're right it chatter.
@Blondihacks
5 жыл бұрын
Its me wrecking stuff That’s great! Glad I could help!
@barakobamadubai
4 жыл бұрын
Very usefull, thank you Quinn
@jitzera1122
2 жыл бұрын
1:15 "this is cheddar." ... No that is butter
@sd94715
4 жыл бұрын
Thanks for video....
@howegav
Жыл бұрын
The more I watch of your KZitem videos, the more I think I'll should check out your Patreon stuff. Thanks for sharing your knowledge. Also, I loved the butter analogy (especially because you used Irish butter 🧈 🇮🇪 ), but using butter was a great was to explain chatter.
@michaelschwartz9485
2 жыл бұрын
Is it better to use "Land O' Lakes" butter to reduce chatter? How about "I Can't Believe It's Not Butter" for reducing cholesterol?! Great series, love your channel!!
@greggarnold5127
4 жыл бұрын
I've just received a new 10x22 lathe and I'm wondering what QCTP you would recommend. I'm looking at an axa wedge type from shars. Interested in your thoughts...thanks
@BernieA01
Жыл бұрын
Thank you very much for your great videos and your superb way of explaining.
@kevinpulver4027
Жыл бұрын
Excellent and very thorough! You're fast becoming my lathe mentor.
@ArtOfGottiKa
4 жыл бұрын
Chatter - if you translate it to german ... hihihi ... schnattern. Ducks are "schnattern" - you know? But you show it so pretty good, you made my day - thanks.
@hartleyhore9040
3 жыл бұрын
I’m glad I stumbled across Your vid very useful, I do suffer with this problem and just thought it was blunt tool edges, excellent video well presented and explained keep up the good work Many Thanks 👍
@mohabatkhanmalak1161
3 жыл бұрын
Excellent, and I like how you describe the workings of the "spring" dynamics in a lathe. Very good tutorials, thanks and keep it up.
@brandon45122
Жыл бұрын
A pretty woman showing me how to machine. What could be better. Your a life saver.
@johneric3886
4 жыл бұрын
I was watching one of your videos the other day. And you use the phrase Bob's your uncle. Been a while since I've heard that phrase. My boss is in Florida for a few more days, it's nice to have some time off. It's little cold here in Northeast Ohio but, we've been lucky this year weather wise. Is it cold where you live?
@Dimisrr
3 жыл бұрын
Very informative series of videos about machining and lathe working. Great work.
@chudleyflusher7132
6 ай бұрын
Thanks so much! This is a great series and you’re an excellent instructor. I’m watching all of these before a training class on the lathe so I’ll have a head start and be able to ask intelligent questions.
@brianhamilton6123
3 жыл бұрын
Great explanation. Chatter is a very simple word for a very scientific phenomonenon of frequencies created through vibration or maybe the other way around lol
@davenicholson3491
4 жыл бұрын
Nice video 👌. In my experience there are basically 2 types of chatter in machining. One is work piece chatter eg. a very little long shaft machined without a stead or without a live centre. Two is tool chatter eg. a boring bar that’s too thin and protruding to far . But like you said rigidly is key in overcoming chatter. Always make your setup as ridge as possible ✊🏻
@louiel8711
2 жыл бұрын
Thank you for posting the lathe and also mill videos, the information presented has been very useful for an apprentice machinist. Thanks again and keep up the good work.
@km18l
3 жыл бұрын
Aw, auto-generated subtitles are in another language other than English and that's the video I need to understand what's wrong with my lathe's chatter and vibration problems :(
5 жыл бұрын
Very nice explanation! Kudos!
@Blondihacks
5 жыл бұрын
André Esteves Thank you! 😁
@markkoons7488
3 жыл бұрын
Can chatter be intentionally used in soft materials to create a decorative surface without harming the lathe? If so, what parameters would encourage non-damaging, repeatable chatter?
@paulmeynell8866
Жыл бұрын
Brilliant thank you
@jamesfield5346
Жыл бұрын
I am so thankful you have made these in depth tutorials. I cannot express how much you have explained, helped and clarified the operations of michining. Your tutorials are the only ones that answer all of my questions without having to ask them. I am going to support your channel as soon as i can afford it. I apologize for not being able to at this time.
@jeremy7923
3 жыл бұрын
Ahhh the cringing at 1:33 😖😬
@qwertyui90qwertyui90
3 жыл бұрын
Hi, can you tell me what the special drill you're using to make the small hole for the tailstock live end to go in and help with rigidity ? looking to get one but not sure what to even search for haha
@frenchroast1355
Жыл бұрын
Just got into machining with a mini lathe and I have to say your vids answer more questions than ten vids of anyone else's of the same subject. Well done.
@TheOriginalMack
Жыл бұрын
More concepts should be explained with butter - nice job!
@JimFleming1953
2 жыл бұрын
Ms. Quinn, I have to ask... Have you ever heard the term "overhang?" This is the second time I've heard you use the phrase "stick out" a few times now. And it might be the vernacular you use, but all my working career we've used the term overhang. There's nothing wrong with using stick out, aside from the fact it makes this old guy cringe. ;-) Yes I'm working my way through your material, from the start to the present... Not bad, "young'n..." not bad at all. I greatly appreciate how conscientious you are about PPE. You know... that stuff that gets in the way of seeing, hearing, touching, and measuring, but keeps chips out of our eyes, terrible screeches, groans, bangs, rattles and clatters, burns and dirt and cuts and nicks from our delicate little pinkies, and finally doesn't help us get the feel we want with our measuring tools (mikes and calipers)... I'm grinning as I write this dissertation... Enjoy.
@Blondihacks
2 жыл бұрын
Every machinist I know calls it “stick out”
@JimFleming1953
2 жыл бұрын
@@Blondihacks Good enough...
@vicosee4439
4 жыл бұрын
Nice 👌
@garthhowe297
2 жыл бұрын
I am a soon to be owner of a mini lathe, and your videos are terrific. They are clear and to the point. Thank you!
@bexiboo1981
3 жыл бұрын
Super useful! I'm glad I found this channel!
@LouwrensvanderMerwe
3 жыл бұрын
Brilliant! Many thanks. Helped me a lot.
@memoonausman7342
5 жыл бұрын
How I can control chattering on long shaft without using ssv because I have not option of ssv in cnc fanuc control lath
@paulmorrey733
2 жыл бұрын
Thanks Quinn
@I_SuperHiro_I
10 ай бұрын
You are very, very good at practical teaching.
@su-vs3em
5 жыл бұрын
Side cutting edge angle effect should have been also explaines
@gagasmancave8859
2 жыл бұрын
Cheers Quin this answered an issue I have been having recently
@michaelberna987
2 жыл бұрын
This is the first video in the series that represents my machining.
Пікірлер: 163