I learned more from watching your video than I have learned from any foreman I have worked with before. I have been working construction for 5 years now and everytime I asked someone information about blue prints I would always get turned away. I've built all this before. After watching your video it finally clicked in my head. Thank you. I will pass this video on to my friends.
@ConstructionKronies
Жыл бұрын
Exactly why I do this, I know how hard it is to get information out those guys. It's a better world when we pass on information and grow💪 right on man!
@dannyredd1912
5 ай бұрын
999⁹90⁰ⁿ⁰òlĺĺ@@ConstructionKronies
@claytonmichael5237
26 күн бұрын
That's one of my pet peeves. When are a journeyman or an apprentice. Not being involved in the drawings to see exactly what you're building. Vertical wall assembly, very important to know. I am a foreman for a union metal stud framing outfit in Alaska. I don't keep my team in the dark at all, in fact the opposite. I am also determined to sharper than I was the day before.
@hh4545
Жыл бұрын
You call yourself a PRO, but i call you are a MASTER. Definitely!!
@ConstructionKronies
Жыл бұрын
Thank you good sir!!
@KevinDiaz-kz9lt
2 ай бұрын
Nice. I wasn’t familiar with the commercial roofing construction. Thanks for the answer as well! I’m glad you were able to answer it.
@ConstructionKronies
2 ай бұрын
You are welcome anytime!
@ConstructionKronies
Жыл бұрын
🚧 Wanna See More? Check out this playlist: bit.ly/ExpertFramingLessons
@lealoctavio18
Жыл бұрын
You come a long long way!! Video are way better more informative. Yup I see 100k subscribers soon keep going keep going!!!! Been watching you since you had less then 500 subs
@ConstructionKronies
Жыл бұрын
Lealoctavio I of course know you! Hope all is well and thanks for watching man I appreciate you!
@joejackson4140
Жыл бұрын
Ya'll are very skilled! Good job.
@lealoctavio18
Жыл бұрын
You should do a video on how to do coner beads
@tracysullivan3968
4 ай бұрын
What methods are available in attaching/connecting pre-sheathed 8'w x 10't steel stud walls, vertically from 1st floor to 2nd floor & 2nd floor to 3rd floor ? Sheer cassettes are already built into our wall panels.
@ConstructionKronies
4 ай бұрын
Yeah, I'm not a fan of this method, panels are a real pain in the butt. However, after the panel is in place we just drill 1/4" to 3/4" bolts or rod into the concrete and fasten down nut and washer. 9/16" to 3/4" #8 or #10 hex self tapers for the top if steel or just hammer drill if concrete like the bottom. If it's suspended outside like curtain wall you need to pre-install clips with hitting shots or pin boots then 4 screws into a stud.
@mgtazco
6 ай бұрын
Great video quick question my plans say to extend the wall 6 inches above the ceiling why is that? Is it so you stop with the t bar and then do separate rooms or is it for soundproof or fireproof? Can you let me know? Thank you.
@ConstructionKronies
6 ай бұрын
Great question, it's just a reference that your walls only have to be 6 inches above tbar and not all the way to the deck. So say tbar is at 9 foot you can use 10 foot studs for the walls, it doesn't have to be exact just a minimum of 6imches. Drywall too, technically your walls will be at 10' 1/2" so you can keep your drywall a 1/2" off the floor and use 10' sheets or cut your sheets to 9' 6" .
@Marco_Polo790
Жыл бұрын
Amazing job, a lot to learn. Thank you for great content 😄 👍
@ConstructionKronies
Жыл бұрын
Thanks 🙏
@bruins7748
Жыл бұрын
On the soffit you can use angle instead of track already and run ur studs across eliminating the track and making it faster .
@ConstructionKronies
Жыл бұрын
yes bro, angle and furring bar yes, i like that better we just keep it simple with the order for the guys and order all 3 an 5
@bruins7748
Жыл бұрын
@@ConstructionKronies not a bad idea . Great videos man very informative not many people take the time to show what there doing .
@rogaia
Жыл бұрын
Good job 👏🏼
@ConstructionKronies
Жыл бұрын
Thank you!
@RICHARDRIMMER-cn7tu
Жыл бұрын
So the corrugated metal roof decking you chose to “shoot” into instead of a self tapping screw was sufficient support for top track, is it common to be able to make protrusions into the roof decking? I have to frame some walls in a commercial application and I’m more of a residential contractor, Thanks!
@ConstructionKronies
Жыл бұрын
Yes, so it's actually not corrugated roofing panels, it's qdeck. On top of the deck there will be another 8" at least of material before the gravel or sbs. Only shoot to qdeck when it is full of concrete. We use heavy gauge framing screws to screw the track to it. Hope that helps my man!
@user-cu2zu3qu7q
Жыл бұрын
Amazing
@mariocrespimilhem
6 ай бұрын
Hello! I find your videos very interesting, and I'm learning a lot from them. Thank you for sharing your knowledge. Could you recommend any free software for metal stud framing design? I'm eager to learn how to design a small house with a metal frame using software. Thanks for your help!
@ConstructionKronies
6 ай бұрын
Outside of AutoCad, sketch up, revit i don't know much for the designing end. I usually just sketch it up on graph paper myself, I freehand with a drawing tablet in Adobe software.
@hlee5200
4 ай бұрын
伟大的分享🎉
@claytonmichael5237
26 күн бұрын
Very educational video. Fish tales, I've seen them done, I didn't know the exact name. You said something about offsetting your bevels? And also T bar and bulkheads. What exactly are you talking about. T bar like cold roll? Bulkheads like soffits?
@TrentTarasen
6 ай бұрын
Can 25g studs hold double 5/8s drywall to help with sound? Span is less than 10’. Can also use a bracket at the middle of span into floor joist.
@ConstructionKronies
6 ай бұрын
Yes for sure 25g will hold double 5/8". I just wouldn't go less than 3-5/8".
@CCNA911
3 ай бұрын
Hi, I just discovered your channel, amazing stuff. I need to do a round framing platform of sorts 72” on the ceiling above a round table. What would you suggest is the best way to go about it? Thanks?
@ConstructionKronies
3 ай бұрын
You can get track that bends now. Draw the circle on the floor even if its a finished floor just tape down some hard board and draw on that. Then make the top and bottom track, forming it to that circle. Then laser up with a couple pin lasers 2 opposite edges to install the top track. Set a line laser to elevation and check your stud lengths, cut them, install a few to get the bottom track on (still checking with the pin lasers that it lines up with the top. After that just finish studding it out and then wrap with 1/4" or 1/2" drywall.
@andyo.4235
3 ай бұрын
Great video, and honestly as a DIY’er it really helps. Question, I’m planning to add a room in my condo unit, as per the builder’s layout plan. The floor is all vinyl laminate. Should the floor be removed or can I install the steel tracks on top of it? Thanks
@ConstructionKronies
3 ай бұрын
Right on!! Yes for sure you can put the track right on top of the vinyl! Just beware, if you ever want to remove the vinyl it will be a hassle to cut the edges around the walls. Most of the time we just put a new 1/4" subfloor over the vinyl for hardwood or carpet. Its very challenging to remove vinyl, it takes a large machine to do it proper / quick.
@andyo.4235
3 ай бұрын
@@ConstructionKronies thanks a lot. But just to be clear, the vinyl i'm referring to are the floating vinyl planks flooring. Not sure if you responded with the glued-on squared tiles in mind, which i totally agree, those are a pain in the neck to remove. So, would that be okay, or should I remove a section of vinyl planks and then install the tracks? Cheers!
@ConstructionKronies
3 ай бұрын
O ya so that makes it easier even, I would put the track right on top. If later they want to remove the flooring you can use the flush cutter around the perimeter and remove the tiles.
@TheTopfu
Жыл бұрын
Good video Do you have video showing how to read the plan and doing the layout?
@ConstructionKronies
Жыл бұрын
Here is a Playlist for you, thanks! Construction Documents: kzitem.info/door/PLRtmYu3z-FENCbUvLNSNbYm-Onk9QlU7R
@Geor-standoff
Жыл бұрын
I'd like to join the next live broadcast, so can you do it in our hourly time?
@ConstructionKronies
Жыл бұрын
I should pick a time and do everyday at that time. On our way to Jasper tomorrow morning I heard that site is going to be nuts but I will think about the time on the way up and be sure to let everyone know!
@VictorLittleJaguar
Жыл бұрын
Great Video Man👍Hoping You Can Help Me With This Question What Are Framers Making Hourly I'm Currently In South Dakota I Was Thinking Of Going Out To Canada Thanks.
@ConstructionKronies
Жыл бұрын
Depending on the province you can make up to $65 an hour as a journeyman in the union and non union pays $45. The piece work and subcontractor arena is more lucrative.
@VictorLittleJaguar
Жыл бұрын
@@ConstructionKronies Doesn't Sound Bad Well Thank You.
@idus
4 ай бұрын
can you use metal studs to build temporary office pods without fixing the studs to the wall for support? It would be a square box about 10x12.
@ConstructionKronies
4 ай бұрын
You sure can. What we have done too is just double sided foam tape, two runs, on the bottom track so we don't make holes in the floor. Cross brace with 4" to 6" flat stock to keep square and if you can brace to the deck above then tbar (suspended ceiling grid.) The walls just have to be 6" above the ceiling.
@idus
4 ай бұрын
@@ConstructionKroniesIf it had to be low sound or sound proof, could I double up the studs and bridge them across the roof using bracing in between and just put sound proof drywall up? My ceilings are 18ft tall. My wife wants to learn drums.
@ConstructionKronies
4 ай бұрын
Yes sorry for the late reply sometimes replies to replies get lost, KZitem needs a better way to tell us. For STC (sound rating) you can insulate, use 5/8" drywall, even go 2 layers of 5/8" both sides, use green glue (soundproofing glue) in between layers or resilient channel.
@meagaindave2049
Жыл бұрын
Like button SMASHED! 😁🍻😁
@ConstructionKronies
Жыл бұрын
Thank you my man! 🙏
@ToddTerrellLife
Ай бұрын
If I have a freestanding metal stud room, which is four walls, how do I run the ceiling joist… The walls are only 8 feet and the ceiling is 10 feet so it’s not going to be up to the metal structure and the building ceiling.
@ConstructionKronies
Ай бұрын
You should run your walls higher or lower the ceiling that's the only way my friend!
@edwardflango3500
2 ай бұрын
Do you use deflection track on top full length walls making studs 1 inch short and letting them float. No stud screws at top of wall
@ConstructionKronies
2 ай бұрын
Yes, every wall that goes u\s structure has to have slot track. We cut the stud anywhere from 3/4" to 1" shorter and we put the screws just below the half way of the slot. You can also take them out.
@paulorourke618
11 ай бұрын
ok nice to watch your videos ..nice work..i am a licensed carpenter but no experience with this stuff but i now am working on a 60 unit building and have put in a bunch of drop ceilings using hat track and shinny 90 they call it all put together with half inch kelly screws ....but now they want me to build bulk heads in each living room to hide air pipes and dryer vents using hat track and l brackets AKA shinny 90 any advice on hat track spacing and screw length or just any advice would be very very very much appreciated...thanks
@ConstructionKronies
11 ай бұрын
Yes my man, use the #8x1/2" wafer screws for metal to metal and the 1-1/4 drywall screws putting the angle to drywall. I always go 16" o.c. for ceilings and bulkheads never 2'. Hope that's helps. My apologies it took so long to get back to you. I just got back from an out of town job was beat.
@user-ev4cy3xj9l
2 ай бұрын
Is that the metal roof that the top track is screwed into asking for a friend 😅
@ConstructionKronies
2 ай бұрын
No we wouldn't screw to a metal roof, what that is -- is metal decking we call qdeck it goes below the roof or is used between floors. Sometimes filled with concrete if between floors. When it's on the roof the next layer will be roof board, rigid insulation and so on depending on if it's sbs, modified or metal standing seam. It's I think 18 gauge usually so use heavy gauge self taping screws.
@RamBo028
Жыл бұрын
Good work!
@ConstructionKronies
Жыл бұрын
Thank you..the carrying channel never came with the delivery. I think these guys cheap out honestly. I always order it and it makes drywall so much easier, just sometimes it doesn't come. I will be putting it in eventually I have extra on another job. Cheers !
@RamBo028
Жыл бұрын
@@ConstructionKronies tell the inspector that.. haha
@ConstructionKronies
Жыл бұрын
Yeah you know, they never inspect our framing only the insulation and fire rating. Do they have it in the code where you are?
@RamBo028
Жыл бұрын
Yes over in Toronto it’s a must every 4’, overlapped and screwed together depending if it’s a fire rated or sound brier. Sometimes they ask for bridging clips..depending on the engineer.
@rantsreviews4609
Жыл бұрын
Do you use 4" stud for the ceilings or 6" what span can you go with 5/8" sheet?
@ConstructionKronies
Жыл бұрын
Mostly 3-5/8 if nothing goes on top. Go bigger both stud width and drywall, maybe add 3/4" ply if you plan to put anything heavy on it. You can really go as big as you want, brace it proper, run furring bar on top with hanger wires to eyelegs in the ceiling, they have for steel self drilling and concrete you can shoot them in with a Hilti. Like tbar but for drywall ceilings. Hope this makes sense.
@willdodd2810
Жыл бұрын
Great informative video, thank you for sharing. How do you go about connecting the tracks to the sheet roof?
@ConstructionKronies
Жыл бұрын
We will use self taping framing screws, wafer heads to the qdeck, and we use clips if the track lands in between them, use self tapers to attach the clips and then we can use regular framing screws to fasten to to clip (for light gauge steel). If it's concrete or structural steel we use the Hilti BX3.
@joelconcrete
Жыл бұрын
Hope all is well with you, how do you put extra support in a ceiling that's 14' by 14'? Can you use a 16' piece of lumber and then attach your track to each side of that for extra support?
@ConstructionKronies
Жыл бұрын
Use hanger wire. You can wrap it around a joist or use eyelegs.
@maximusalmaty
5 ай бұрын
Teaching video where teachers talk about how good they are lol.
@ConstructionKronies
5 ай бұрын
Your missing the point, I try to tell people how long it takes so they know how long it takes.
@deeworkzz2861
Жыл бұрын
at what point would you introduce black iron through the ratholes? my foreman was explaining it to me the other day on a 12ft soffit we installed. at what height would you normally do this
@ConstructionKronies
Жыл бұрын
To be honest with you, I'm not sure. The rod is usually bolted in before we start by the iron worker. If the soffit needs any structural reinforcement the specifications will surely tell you. We stiffen our soffit with channel and furring bar running along the inside and maybe wire or pencil rod we work on 4x4 max spacing at any elevation.
@Joe-jv5mm
Жыл бұрын
Apologies for stupid ? What's a T Bar, joint/taper from 🇮🇪 looking to learn about metal studding, Great Videos on Your Channel 👍
@ConstructionKronies
Жыл бұрын
So cool! Tbar is what we call suspended ceiling grid, acoustic ceiling grid, 2x2 or 2x4 grid! Does that make sense?
@Joe-jv5mm
Жыл бұрын
Cheers man big help, I do more domestic work, small job's but I like to do it right, Your Channel is a Great Resource for the small Guy, thaks for taking the time to Reply 👍from 🇮🇪 🥃
@makermarc70
Жыл бұрын
Hey Chris . Great teaching video. I like the video edit format with your narration. Please, You mentioned something about offsetting bevels in comercial. I am missing what you mean. Its around the 5 min mark in the video. I think. Anyway explain if you ever get time. Thanks. Good work.
@ConstructionKronies
Жыл бұрын
Yes I think what your asking is about staggering where the sheets land on either side of the wall. you want to make sure the bevels (sheets) don't land on the same studs. For example: Side A we will start with a 16" strip then full sheet and Side B we start with a 32" pc so that the joints are staggered. Hope thats it bro!
@amritpalmatharu7
27 күн бұрын
Do you use slotted track under q deck for bulkheads?
@ConstructionKronies
27 күн бұрын
No, only on full walls from floor to deck. Use standard track for everything else.
@jezreeljamesmanrique6724
10 ай бұрын
Where to used tracks? Is it only on ground and top?
@ConstructionKronies
9 ай бұрын
Pretty much, the STD track can be used for headers, box beams and, for penetrations. Slott is only for under structure top track for deflection and fire rating.
@christianarrizon9796
Жыл бұрын
Do you ever just use 90 90 n just hand shake everything instead of of using bottm track
@ConstructionKronies
Жыл бұрын
Sure, sometimes we do it all with angle and furring bar, carrying channel 👍
@antoinezihenni1832
2 ай бұрын
HI
@ConstructionKronies
2 ай бұрын
Yo Dog!
@shaneash1598
2 күн бұрын
Cake/ gravy
@ConstructionKronies
Күн бұрын
Gravy f-ing train baby!
@shaneash1598
Күн бұрын
@@ConstructionKronies I'm on the t-bar right now fixing a f***** up ceiling. that was just built it was out of square diagonal measurement was 53"😂 As opposed to 52 and 1/4 " what a mess The boss wants it taken apart and reused ffs lol anyway stop giving away trade secrets .. It's almost like A green horn watched one of your videos and tried to build a t-bar ceiling😂 With that being said, mad skills fellas lathers Rock 💪....
@ConstructionKronies
Күн бұрын
@@shaneash1598 HAHA yeah man we have been seeing so much of this out there and is why I am trying to help. Mostly cheap labour is the reason for all the shit work. Canada right now is so bad we are literally driving the modern day slave trade with these unskilled cheap workers its very sad for everyone.
@shaneash1598
Күн бұрын
@@ConstructionKronies yes indeed cheers.
@scooleydc3457
Жыл бұрын
Great information in this video. How long of a span can you do on a ceiling before you need to add a support to the concrete floor above? I have a 16’ x 10’ space. Using 1/2” drywall. 2 1/2” x 10ft stud. Would I need to support it?
@ConstructionKronies
Жыл бұрын
Yes grab some furring bar, run 3 rows (rule is braces every 4x4sq area) equal distance apart and make sure to attach it to every stud on both sides of the furring bar (2 screws every stud) make sure it literally runs end to end screwed into the track either end and also screwed together, then shoot kickers up to the ceiling every 4' staggered on those runs. You should be able to hang off it with no movement.
@leecarey2516
10 ай бұрын
What gage are your metal studs?
@ConstructionKronies
10 ай бұрын
On this job it was 25 gauge.
@rileyjenk
Жыл бұрын
Any considerations when framing walls for a walk in shower?
@ConstructionKronies
Жыл бұрын
Use 20 gauge studs and blue mold resistant board! Wrap it with detra as well before tile.
@rileyjenk
Жыл бұрын
@@ConstructionKronies thank you! Been twenty years since I did metal framing with my dad (was twelve= nearly zero help). Lots of detail I hadn’t considered.
@rileyjenk
Жыл бұрын
@@ConstructionKronies Follow up question....do you recommend 20eq studs or actual 20 gauge?
@ConstructionKronies
Жыл бұрын
@@rileyjenk 20 gauge studs, they are my favorite gauge. Super strong and efficient!
@KevinDiaz-kz9lt
2 ай бұрын
What is your ceiling attachment detail for the top track of the hulk head to the roof? You’re not screwing into the ceiling panels are you? Serious question, not a critiquing tone, just super curious
@ConstructionKronies
2 ай бұрын
Yes we screw the top track to the q deck if it's hollow or shoot it with direct fastening tool like hilti or ramset if it's filled with concrete. The roof itself will start 3 to 6" above the top flute so you never have to worry about holes in it.
@khrystyna.vavryniuk
Жыл бұрын
By code can you use it Stud Crimper or you need to use only screws?
@ConstructionKronies
Жыл бұрын
I don't believe it is code. What you need to know is if it is in the construction specifications either in the contract documents (drawings, specifications) or product details. They will tell you what type to use and where to use them. If it is not specified I would say use what you want. At the end of the day the drywall will hold it all together if your screws are in the right spot. I think it is industry best practice to at least screw 1 side in and crimp the backs, I know guys who crimp only the top back. If you can keep studs proper on center, and square go for it. We screw them in always so its faster to drywall and better to tape and so on. Its important to have square studs and screw the soft side in the bevel first. That way the sheets won't pop out and give your walls humps.
@Ticonderoga12
Жыл бұрын
Hi, what gauge steel is recommended for residential ceilings?
@ConstructionKronies
Жыл бұрын
25 gauge, you can use 3-5/8", 6" studs and track or 25 gauge furring bar and angle depending on your clearance.
@Ticonderoga12
Жыл бұрын
Thank u so much, cud u do a video on hanging prehung doors using metal studs, nobody has one on yt.
@user-pg4xq2xz2b
Жыл бұрын
Where you are in canada????? O where ????
@ConstructionKronies
Жыл бұрын
Edmonton Alberta!
@Omarmarquez-pg4yh
10 ай бұрын
HOW MANY LINE FEET FOR FRAMING SOFFIT TYPE L ON 8 HR YOU THINK ITS GOOD FOR ONE GUY
@ConstructionKronies
10 ай бұрын
That could depend on many factors, but if you can complete 10 feet an hour, you are doing well.
@RamBo028
Жыл бұрын
Where are the carrying channels! Lol
@HICDIY
9 ай бұрын
Great job how I can contact you
@ConstructionKronies
9 ай бұрын
chris@constructionkronies.com
@campervanbreton8918
Жыл бұрын
Hi, what's your annotation software?
@ConstructionKronies
Жыл бұрын
I use Adobe Acrobat for everything now. I used to use Nitro PDF before I started editing video but having the creative Cloud apps Acrobat Pro is included and really great stuff. nitro has more estimating tools tho.
@carterbacon6232
Жыл бұрын
What about cold row ?
@ConstructionKronies
Жыл бұрын
Do you mean wall channel? Every 4' it goes we just didn't have it on site but I will put it in before drywall.
@carterbacon6232
Жыл бұрын
@Construction Kronies very nice
@me7229
Жыл бұрын
What happened to the Sunday morning lives?
@ConstructionKronies
Жыл бұрын
They will be coming back bro I promise, work has been just so nuts I haven't had any time to program a new stream in obs. I'll be live at some point today from the studio. My apologies bro. I miss them a lot myself.
@GoatZilla
Жыл бұрын
why can't we build houses like this?!
@ConstructionKronies
Жыл бұрын
Ive done 3 houses with steel, we are working on one right now. Will be back on that job next week. They still aren't doing it right but if I was designing it I would do it like we do in commercial for sure. We talk about this a lot. I have tried to educate the builders on how to do it proper but they keep going back to panels and it doesn't work with panels. (Pre built 10x10 sections)
@denisbonilla293
Жыл бұрын
Do you work in Calgary?
@ConstructionKronies
Жыл бұрын
Mostly in Edmonton, live in Terwilliger but I do jobs all over. Calgary, cold lake, Jasper. We were building mansions out of steel stud in Calgary last year.
@denisbonilla293
Жыл бұрын
@@ConstructionKronies I live in Calgary I’m 20 and looking for work I have 3 years experience It would be a great opportunity to be taken under your wing I would learn a lot from you I’ve been watching your videos since 17 and they helped me a lot
@ConstructionKronies
Жыл бұрын
That's sick man. We have 2 jobs coming up in Drayton Valley here soon. Shoot me an email chris@constructionkronies.com let's keep in touch I'll shoot you my number.
Пікірлер: 132