Work play drive is by far the best on KZitem very detailed.
@WorkPlayDrive
4 жыл бұрын
Wow, thanks!
@ParabellX
4 жыл бұрын
Back again, just finished this, and I gotta say, I love it. I had a check engine light for P121B which is the actuator, and this fixed it permanently. It’s louder if you have a mid muffler delete, but stock exhaust is very subtle. No more squeak from my right active exhaust as well. Easy install. Thanks again for this video!
@WorkPlayDrive
4 жыл бұрын
awesome!!
@Boogiesu12
4 жыл бұрын
@@WorkPlayDrive Is there a potential problem if it remains open? I have a P121B code as well - took it to the dealer and he said that the damage was caused by hitting something. I did run over a skunk(night time) and heard the bang and it bent the actuator. The service dept told me the problem is severe and leaving it in the open position will cause severe damage to the engine.
@WorkPlayDrive
4 жыл бұрын
The decision is up to you, but 😂 sorry severe damage to the engine 😂 did they explain how? what about everyone who removes the CATs and straight pipes or installs a custom exhaust?
@mikeprice8307
3 жыл бұрын
@@Boogiesu12 so what was your final resolution to the p121b?
@blacksrt3791
3 жыл бұрын
2018 scatpack with mid muffler delete. Removed active exhaust fuse 5 seconds after cold start Sounds amazing now ! Even louder But 3x deeper tone. Noticed big difference in back pressure so returning fuse due to check engine light
@mikebythesun
5 жыл бұрын
I installed this on my HC a couple months ago and have been throwing a code. The manufacturer told me I likely didn’t install the M-FER perfectly lined up (crooked), but said nothing about the springs. Thanks for sharing this - looks like I found my problem. Great video as always.
@WorkPlayDrive
5 жыл бұрын
Thank you and I hope that's the issue.
@ssparrrkyy
3 ай бұрын
FYI: Check your spring for wear especially if you have the original without the Teflon insert. The spring will slowly wear down and may need replacement.
@MYute87
5 жыл бұрын
Thank you for the assistance on the install, I played the video on my phone while installing just to make sure.
@WorkPlayDrive
5 жыл бұрын
Happy to help 💪
@glane5854
5 жыл бұрын
This is my 1st comment/review I have ever done. The reason being is I wanted to let you know that this is a great video, not only for the install but also describing the remedies and issues that require you to have it.!
@WorkPlayDrive
5 жыл бұрын
Thank you 🙏 I appreciate that.
@batzparanormal1079
4 жыл бұрын
Love this product.. it helped the noise on my exaust valve .. I had a noise while I accelerate but this product took it away....great product
@WorkPlayDrive
4 жыл бұрын
Awesome 👌 so true it gets rid of that annoying squeaky exhaust valve problem
@burst-__-matiic8311
4 жыл бұрын
Really? I’m having that same problem, how’s it been doing as of now?
@batzparanormal1079
4 жыл бұрын
@@burst-__-matiic8311 the sound is gone u gotta check sometimes to make sure is tight and the screws aren't loose
@Kdaybaby
Жыл бұрын
I bought this to get rid of my squeaking problem too. I now have check engine light on bc of the install… did the mechanic install it wrong ?😢
@WorkPlayDrive
Жыл бұрын
@Kdaybaby there is a possibility that the mechanic did install it incorrectly. The check engine light will show up when the actuators don’t go through a full cycle and receive the expected input If you left the actuators unplugged or he didn’t install it correctly, it will receive the wrong feedback and trigger a check engine light after 20 minutes of retrying
@jimferry4751
4 жыл бұрын
Thanks for the video. My install went perfect. No CEL and sounds great. Next up is mid-muffler replaced with Vibrant 1794's. Thanks again for a perfect install video.
@WorkPlayDrive
4 жыл бұрын
🤙
@oldschoolrichierich4670
5 жыл бұрын
The best install video on mfer1 Michael great guy !
@WorkPlayDrive
5 жыл бұрын
Thank you!
@oldschoolrichierich4670
5 жыл бұрын
Workplaydrive I know you're a busy man but check my channel out and my KZitem install video on the MF for 1 which watching years made it extremely easy and I plugged you big time thanks for all the awesome info that you provide so I have one question for you when you put a 180 thermostat in a 392 I'm thinking you need to have the fans recalibrated am I correct and what I want to know is will the Dodge dealership do it for you or letting them know you changed the thermostat out will it void the warranty any info you have on this would be greatly appreciated my friend hope one day we get to meet in person
@RTLife
5 жыл бұрын
Nov 3rd buddy - This is a really cool find for people that want to hear that nice exhaust note regardless of mode. nice install
@WorkPlayDrive
5 жыл бұрын
What's November 3rd???
@RTLife
5 жыл бұрын
Next meet - Pilgrim State in NY. If you want to come hangout again
@WorkPlayDrive
5 жыл бұрын
Whoo hoo!
@glockmodder
4 жыл бұрын
I got a ticket not to long ago for LOUD EXHAUST I was in sport mode stupid ticket so I'm gonna make it louder now thanks. I still don't understand why we can't just plug in a resistor and make it not get a cel you can do it with a o2 sensor or many other emmisions equipment. Also are you trolling us with that bandaid
@WorkPlayDrive
4 жыл бұрын
Lol nope cut my hand and that’s the one my son gave me 😂 The system needed to go through a cycle to confirm the exhaust valves are unobstructed. A resistor won’t work in this situation because each position has a value that needs to be detected.
@juanfrancisco7241
11 ай бұрын
Thanks for the video!! Will like to do this on my 392 charger.
@MeanBee392
5 жыл бұрын
Awesome install video brother! Clear and very easy to follow along! I would love to see a video on how it sounds cold start, and drive by. I wouldn’t mind doing something like this to my car!
@WorkPlayDrive
5 жыл бұрын
It is absolutely impossible to record the difference with this I am installed almost all recording devices will normalize the sound so loud exhaust louder exhaust and stupid loud exhaust all sound the same
@jjzbyszinski
5 жыл бұрын
Great install video. I ran into the dreaded exhaust valve squeak on my 2015 SRT Charger and found your video when I stumbled upon solutions to keep the valves open. Needless to say I will definitely be ordering these.
@WorkPlayDrive
5 жыл бұрын
Oh man not the squeak 😱
@apariciopass678
5 жыл бұрын
Yeah mines just start doing it not to long ago. Took it to the dealership they told me $3800 bucks for a whole new exhaust system. Let me know if it work for you. I will ordering if it works.
@aceofspades2352
Жыл бұрын
@@WorkPlayDrive I’m in the same boat with the squeaky squeak sound like u getting up from a bogus mattress. 😢
@WorkPlayDrive
Жыл бұрын
For the squeak issue you may want to check out the inactive exhaust it removes all moving parts. kzitem.info/news/bejne/pW2c4K1vj2ukgYo&feature=shares
@aceofspades2352
Жыл бұрын
@@WorkPlayDrive appreciate it bro. It made my check engine light come on code U1140
@Jaydee6.2
5 жыл бұрын
I’ve got the active exhaust solutions one but these look a lot better.. might make the switch.
@WorkPlayDrive
5 жыл бұрын
I like the fact that they bolt in place 👍
@cummins2getu
5 жыл бұрын
Have the same kit on my 16 Scat Pack Challenger. Love the simplicity of this kit. Love the new sound even better.
@Kdaybaby
4 ай бұрын
Has it thrown a code at all?
@WorkPlayDrive
3 ай бұрын
Nope no codes on any of the ones I installed for myself or friends.
@harrypuran7446
3 жыл бұрын
A check engine light came on for me? Any causes why it happened?
@scott_0492
5 жыл бұрын
great video! thanks for the code, ordered mine last night, he shipped it out already and I'll get it Monday, wow!!!!!
@vedette26
5 жыл бұрын
Hello from Quebec, I received it, good quality, but the only problem I have, well I still have not received my new Scat Pack widebody 2019, probably 2 weeks again. I can not wait
@WorkPlayDrive
5 жыл бұрын
Congrats, the only thing more difficult than waiting for the car is waiting for the 500 mile break in to unlock the fun features ;)
@BBHemisnJets
5 жыл бұрын
@@WorkPlayDrive 500 and 1 miles to be exact (501) I couldn't wait either, so I tested it......lol. ☺ kzitem.info?o=U&video_id=7QawY6ypZgE
@redkeyinuse4754
4 жыл бұрын
I don’t notice any difference in exhaust tone when I have my cat in track. I think it just opens faster. Not stay open.
@oldschoolrichierich4670
5 жыл бұрын
Also stood the squeak the active exhast flap gets after a year or two old
@goodknight6828
4 жыл бұрын
OLDSCHOOL 392 I noticed this squeak immediately the next day 😕
@JoeSmoe1
3 жыл бұрын
2:23 for mechanics looking to learn how to install 8mm socket and 2.5 Allen wrench
@sniffmoneyArmsAndAmmo
Жыл бұрын
Good installation video and clear explanation of everything going on... I need this for my RT 👍🏼
@WorkPlayDrive
Жыл бұрын
Thank you don’t forget to check out my other video titled inactive exhaust. It’s an electronic solution.
@sniffmoneyArmsAndAmmo
Жыл бұрын
@@WorkPlayDrive ok thanks appreciate the info I will check it out
@MrChefdong
3 жыл бұрын
Just installed mine on 2016 auto scat. Hearing the beeping every min or so and check engine light on. Any advice???
@WorkPlayDrive
3 жыл бұрын
Make sure you plugged them back in and the springs are seated correctly
@braney56
5 жыл бұрын
I installed the MFER1 on my 2016 Scat Pack, it's a subtle difference. Next I'll do the mid muffler delete which I think the MFER1 is necessary anyway to get the full effect. I don't see the active exhaust addressed in any of the mid muffler delete videos I've seen. Just cutting out the mufflers doesn't change the action of the active exaust.
@WorkPlayDrive
5 жыл бұрын
Mid muffler makes it louder with a little more raspy sound, but correct no changes to the active exhaust.
@stevev7402
5 жыл бұрын
Another great video, always informative and complete but that is WAY too much money for what it is. Even with a $10 discount.
@conceptautosolutions6584
5 жыл бұрын
Well! Now to come up with the cash before Nov 13! Thanks for this @workplaydrive 🙌🏻🙌🏻🙌🏻🙌🏻🙌🏻🙌🏻🙌🏻
@davebaum7018
Жыл бұрын
Seems like sand, salt, dirt will cause problems down the road as the spring and solenoid shaft are now open to this.
@WorkPlayDrive
Жыл бұрын
This was one of my concerns until I got down there and started taking it apart. I found the spring and solenoid are open right from the factory
@eddiecampbell5925
5 ай бұрын
Why not just remove the spring and wire it open and put back together?
@WorkPlayDrive
5 ай бұрын
The actuator has a set path from full open to full close and if it doesn’t receive the correct travel it will throw a code after 20 minutes. So if you wire the valve open you need to trick the actuator that it’s still connected.
@jaci2002
Жыл бұрын
Do you know if this kit activates a check engine light on?
@WorkPlayDrive
Жыл бұрын
The purpose of the kid is to prevent to the check engine light. I never had a check engine light while using this.
@aquarius8063
2 жыл бұрын
Great install video. I have a 2018 Challenger Scat Pack and getting a random chirp from the back. After much research appears to be active exhaust. No error codes yet. When I put into Sport Mode, chirps go away…which confirms it must be AE. So I saw a couple of videos showing guys squirting WD-40 dry lube into the small port holes. I tried but still seems to chirp. I’m going to try another healthy squirt today and see if that will fix it, otherwise this looks like a good fix. I currently have a mid-muffler delete. So not sure how much louder the car will be with exhaust open. Thoughts? I had an appointment to take into dodge to repair…holding off until I know more…thanks again, very helpful understanding the AE.
@WorkPlayDrive
2 жыл бұрын
That chirp is often the butterfly inside the exhaust pipe. Now you have another option as well. This one takes the mechanical out completely and just responds electronically. Check out my new video kzitem.info/news/bejne/pW2c4K1vj2ukgYo
@fineromike3544
2 жыл бұрын
Hey @aquarius i have a 2018 srt 392 and recently cut off the mufflers and a week later i get the same chirp assuming it’s the AE,, did you ever go to the dealer and figure out what the issue was or did this do the fix ?
@johnhilt1990
4 жыл бұрын
I have a 2017 RT. I’m getting a check engine light on (P121B) will this solve the issue?
@jason_loja10
4 жыл бұрын
I would take it to an auto shop that specializes in exhaust. I took it my 18' RT to the dealership and they tried up selling me a whole new exhaust system. Turns out the spring in actuator was acting up. Yours might be just a simple fix like mine.
@johnhilt1990
4 жыл бұрын
Jason Loja I got under the car and it turns out the entire active exhaust motor stopped working
@bigwewe6735
4 жыл бұрын
@@jason_loja10 im having this problem right now. Ive got an 18 Challenger RT that squeaks everytime this actuator rotates. Did you fix this and how?
@julioalfaro6749
3 жыл бұрын
How did you fix it ?
@carlosbigard2853
2 жыл бұрын
@@bigwewe6735 use lithium spray grease and open the actuator open using 8mm and spray the hell out that spring and all around the inside…cheap $5 fix bro if that doesn’t work buy this beast Kit he’s showing! Or replace the whole actuator for $180
@jameswinstead4027
Жыл бұрын
I installed mine and the active exhaust p121b is still showing
@TowerTruck14
5 жыл бұрын
Great Video I'm def Buying this mod for my Black Bee , one stupid question because these spring open to dirt , road grim , road debris etc.. water ? What the long run on this malfunctioning ? only because the spring is exposed ? That's why Mopar puts it in a housing to prevent this.
@WorkPlayDrive
5 жыл бұрын
You can get the MFER1 extreme if you are worried about debris. Keep in mind while the factory parts are covered they have openings so the springs are still exposed to the elements.
@user-ev6yr5ry1j
9 ай бұрын
where do i buy springs
@WorkPlayDrive
9 ай бұрын
You can grab the springs from their site mfer-1.com/
@carlosbigard2853
2 жыл бұрын
Great video! I have A 2018 RT so my spring is OK??? Also which lit should I order
@renerodriguez5800
8 ай бұрын
Where can I buy it
@WorkPlayDrive
8 ай бұрын
Links are in the video description 👆
@mazinalansari88
Жыл бұрын
Hi man Thanks for video But, why it can't be just fixed ? Do you mean it wasn't a necessary feature from Dodge? What I am losing by doing this?
@WorkPlayDrive
Жыл бұрын
The feature was added to comply with government regulations This just bypasses the part that makes your active exhaust quieter so it’s louder all the time
@tyscottTHEbeast
3 жыл бұрын
Hello, I removed my midmufflers on my 16 hellcat and i'm getting a p1217 code but not one for the other side. I took off the actuator and put it back on and it seemed to fix the issue for about 2000 miles, but it came on recently again. Do you have anymore info on those performance codes and what can cause them, like a bad spring? I'm hesitant on installing the mfer, just out of respect for the neighbors, but the cel is definitely annoying, as I don't want to carry a code reader with me to clear it all the time. Any info you have would be great, since it seems like there is little to none out there on the forums.
@WorkPlayDrive
3 жыл бұрын
P1217 has a few meanings but it’s usually the active exhaust. I know the early 2015 models had a smaller spring that would cause an issue. Have you gone under the car to see what’s going on with the active exhaust? Is the plug secure, has the spring slipped off?
@BillyKnockout
2 жыл бұрын
My '15 Challenger is showing the P1217 code . Will this remedy that ?
@WorkPlayDrive
2 жыл бұрын
You may want to check out the zAutomotive inactive exhaust. It’s an electric solution. This will completely eliminate the whole setup including the actuators which are probably the part that failed. Check out my video on it. kzitem.info/news/bejne/pW2c4K1vj2ukgYo
@derottv
4 жыл бұрын
I installed this almost a year ago and I’m getting a slight squeal, have you ever experienced this?
@WorkPlayDrive
4 жыл бұрын
No squeal yet but they did modify the design to add a little Teflon pad underneath it. Maybe reach out to them and see if you could put that pad on the older models
@CarlosTorres-zk4ik
5 жыл бұрын
got a new discount code? 😬 and GREAT at explaining everything!!
@WorkPlayDrive
5 жыл бұрын
Soon they are releasing new firmware and once my video is up I’ll have a new code.
@deezygamingmedia
11 ай бұрын
Do you need this if you have an aftermarket exhaust system installed?
@WorkPlayDrive
11 ай бұрын
If your aftermarket exhaust removes the OEM active exhaust yes. But there is a better solution for when the modules are removed. Check out this video. kzitem.info/news/bejne/pW2c4K1vj2ukgYosi=PB79IMlfNZzA2dEM
@richf9608
Жыл бұрын
I don't think you were supposed to put a lock washer after the first 8mm nut and before the standoff.
@sladjanbegic
4 жыл бұрын
Would this remedy my rattle that I’m getting from my active exhaust?? It’s driving me insane. My car is out of warranty and don’t want to have to replace the exhaust system?? Help help help!!!?
@WorkPlayDrive
4 жыл бұрын
That’s a tough question rattles can come from anywhere.
@robrei2117
4 жыл бұрын
Same reason im watching this video im going crazy with that rattling noise
@sladjanbegic
4 жыл бұрын
Update: I fixed my rattle turns out it wasn’t my active exhaust valves. It was my heat shield right underneath the front seats. It was touching my exhaust and creating a rattle. I bend it back up and boom just like that nice and quite.
@sladjanbegic
4 жыл бұрын
kzitem.info/news/bejne/xamOmYB4fl9qem0
@aaronknowles8198
4 жыл бұрын
This fixed my exhaust rattle but now I have a beep like 10:16 everytime I start my car??? What’s causing this?
@WorkPlayDrive
4 жыл бұрын
I have not installed the MFER-1s on my hellcat yer and I hear the same sound every time I start my car.
@tflnorthamerica4585
Жыл бұрын
I was wondering did you notice any loss in bottom end torque using these?
@Nfamous_707
4 жыл бұрын
I’m currently using a different kit that requires the actuators to be ZIP-TIED up out of the way... fuckn hate it. I’ve been putting this off for awhile. Just ordered these finally. Great vlog.. very helpful.
@WorkPlayDrive
4 жыл бұрын
I'm familiar with the Zip tie option :) these are definitely a much more elegant hard mounted solution.
@steve7837
4 жыл бұрын
Does installing this keep the cold start volume/note? My main thing is I want the idle to be louder. The cold start on mine is loud as cold starts are, but it quiets down so much after about 20-30 seconds (presumably the valves closing).
@WorkPlayDrive
4 жыл бұрын
No the coldstart sound has a bunch of other factors along with it one of which being a higher RPM. The active exhaust valves are open for the entire coldstart and they are still open after a minute as the car starts quieting down
@SoGQue
2 жыл бұрын
Installed it now my check engine light is on😩
@WorkPlayDrive
2 жыл бұрын
2 things to check. Are the actuator plugs connected securely and were the springs in the same orientation they were on the vehicle? Sometimes they fall off and people put them on backwards.
@mydigitallife8311
5 жыл бұрын
oh boy, $300 and my neighbor will love me even more. I leave my house at 2 or 4 AM.
@justchairsandtables
5 жыл бұрын
It doesn't help cold start. Only about 30seconds in when it would normally close
@brosiferous
5 жыл бұрын
Excellent job on the vid, seems like a great product. Is there anything out there that will let me close my exhaust butterflies on startup? I love the raspy cold starts, and track mode with the tazer... but sometimes I need to leave early for work or want to keep a low profile starting up the car.
@WorkPlayDrive
5 жыл бұрын
Nothing on the TaZer yet, stock they run open on start. An unlocked pcm and a tune will do it but that gets really expensive.
@brosiferous
5 жыл бұрын
@@WorkPlayDrive Thanks!
@quintosol2006
5 жыл бұрын
My 17 Scat has completely stock exhaust. This would give me the sound of the cold start all the time throughout my drive right?
@WorkPlayDrive
5 жыл бұрын
Nope cold start has nothing to do with your active exhaust. The active exhaust is ope all the way even after the car gets quieter. It’s more like what you get when you drive in sport mode
@quintosol2006
5 жыл бұрын
@@WorkPlayDrive thank you sir. As always awesome info and videos.
@ParabellX
4 жыл бұрын
I know this is a dumb question, but did you jack the front or back of the car up? Just ordered these yesterday.
@WorkPlayDrive
4 жыл бұрын
I lifted the rear of the car the modules are located in line with the rear tires.
@ParabellX
4 жыл бұрын
Work Play Drive Thanks!
@Hemifam
5 жыл бұрын
Nice bandaid bro! 🤪
@WorkPlayDrive
5 жыл бұрын
Paw Patrol is on the role
@MrJohnsl40
4 жыл бұрын
Did the mid mufflers delete six months ago my cel came last weekend. ( Driver actuator fail). Went to the shop replace the spring and installed the mfr1 kit. Reset the car cleared cel but I came back with in one hr. Smh
@WorkPlayDrive
4 жыл бұрын
If the actuator fails then it needs to be replaced. The sensor needs the actuator to do a full sweep if it can’t it keeps trying for 20 minutes then throws a code the next start up.
@MrJohnsl40
4 жыл бұрын
Work Play Drive thanks so much for the reply I was installing the kit while watching your video. Should I reinstall the mfr1 kit when again when I replace the actuator? Or do you think it's fine just to put the new a actuator on..
@lalomontoya1444
Жыл бұрын
Hey so I just installed some headers on my Dodge Challenger rt 2017 it cost me 2,000 for the headers I had some one install them and wen I start it up it makes a loud rubbing or scraping noise even wen I drove for bout 5 min then goes away it comes on every time I start up my car what do you think it could possibly be plz if anyone can help me 🙏
@WorkPlayDrive
Жыл бұрын
It could possibly be the active exhaust butterfly valves. To test what you can do is go underneath and just unplug the active exhaust modules. You will throw a check engine code if you drive it for more than 20 minutes but don’t worry about it because once you plug them back in drive the car for a bit then restart it will go away
@WorkPlayDrive
Жыл бұрын
If it turns out, it’s the valves, you can easily use an active exhaust delete kit to fix the problem.
@NJ_Scat_Hemi_Orange
Жыл бұрын
Old video but question for 2023... Is MFER-1 still relevant? My 2022 Scat pack has track mode. Is the MFER-1 even needed?
@WorkPlayDrive
Жыл бұрын
For some yes. if the stiffness of the suspension, throttle sensitivity and aggressive shifting while Track mode bothers you the MFER-1 or the zAutomotive inactive exhaust (newer video) will keep them open in any drive mode. Even eco 🙃 Inactive exhaust video 👇 kzitem.info/news/bejne/pW2c4K1vj2ukgYo&feature=shares
@NJ_Scat_Hemi_Orange
Жыл бұрын
@@WorkPlayDrive gotcha. MFER plus custom drive mode give your the open valves without requiring you to choose track transmission.
@chaunbishop9373
4 жыл бұрын
Quick question, I completed the install and one small issue. On the driver’s side, there is a hose right in front of the top screw. It was difficult to even get the original screw off but as I put the new assembly on the final screw on the motor, I just couldn’t get a socket on it. I did use threadlocker and hand tighten but do you have any suggestions to tighten with a tool.
@Primerk5
5 жыл бұрын
Do you feel having it in track mode would make the throttle too touchy for a daily driver use on the SP? (not sure how much the throttle response changes between sport mode and track mode) I have an early 2015 SP so i'll probably need the springs. I'm weighing the price of this with the springs vs the TAZR.
@WorkPlayDrive
5 жыл бұрын
Personally the difference between driving in normal and sport mode takes a moment or two for me to get used to the Clutch release. Personally these make it much easier to just drive and not worry about it. For the auto track mode not only increases the throttle response but also makes the shifting points a little more aggressive and jerky
@arthurharris4367
4 жыл бұрын
Okay I got it in the mail but when I put it into sport mode will it change anything? Do I still get sport mode ? Will it affect sport mode will I lose anything?
@daytona5.722
5 жыл бұрын
Those look nice! Great video!!
@WorkPlayDrive
5 жыл бұрын
Thank you
@michaelkuntz9175
2 жыл бұрын
Sorry for the double comment I’m looking at both parts but I have a cat back exhaust on my scat right now, will that change anything on me buying this? Just trying to see if it messes anything up because I have that on already?
@xavierstribling6176
4 жыл бұрын
Will this work on a 2016 Charge Scat Pack with after market Borla exhaust installed?
@elijahboston8621
2 жыл бұрын
Can this be used on the 5.7 hemj?
@WorkPlayDrive
2 жыл бұрын
Yes as long as it’s 2017 and up. Earlier 5.7s did not have active exhaust.
@hemijl8304
5 жыл бұрын
Great install video.
@WorkPlayDrive
5 жыл бұрын
Thank you!
@RaulGarcia-fj2mt
2 жыл бұрын
Where i can buy
@mdecker0420
5 жыл бұрын
Great vid buddy!! Keep em coming!!
@WorkPlayDrive
5 жыл бұрын
Thank you!
@randomdude4160
5 жыл бұрын
I have a quick question and hope u can help me out. The pancake spring broke on my 2015 challenger scat pack and dont really have the money to buy the whole mfer system. Will the new style springs work with the old 2015 actuators?
@WorkPlayDrive
5 жыл бұрын
Sorry I'm not sure if it would fit, but you could also contact the dealership parts department and get the part number for the smaller spring.
@arthurharris4367
4 жыл бұрын
With this on and in sport mode what is the mfer1 like? I have a 2018 rt ? I don’t need to put it in sport mode after but if I do what is it like and do you recommend it is there any sound difference etc. ????
@hebee81
5 жыл бұрын
Would you know if there is anything out there to make it quite or loud when you want. Like the NPP on the Camaro and Corvette.
@WorkPlayDrive
5 жыл бұрын
Not with the stock exhaust, but I did install the Noweeds and it allowed me to go from stock loud to Extremely loud at the push of a button.
@nathanwall9160
5 жыл бұрын
Work Play Drive can you install these and the noweeds? I like the simplicity of this. But want the sound of the noweeds when I’m messing around. My plan is to install these on a flowmaster cat back system.
@ogtimmy2355
5 жыл бұрын
I ALWAYS drive in Sport Mode. So I don't actually need this then correct?
@WorkPlayDrive
5 жыл бұрын
I know sport keeps the AE open more, not sure if it's open all the time though.
@ogtimmy2355
5 жыл бұрын
@@WorkPlayDrive i have the Tazer too..so i could put it in track mode. But i never noticed a difference in track mode. 🤷♂️
@justchairsandtables
5 жыл бұрын
Only track mode. Still need Mfer on sport.
@terrym.6795
3 жыл бұрын
I took my car to a repair shop and they said because I have a mid muffler delete, that's damaging the valves. Is that possible?
@WorkPlayDrive
3 жыл бұрын
I’ve been thinking the same thing, that mid muffler delete is the cause of it, but mechanically I can’t see how that would damage the metal butterfly 🤷
@terrym.6795
3 жыл бұрын
@@WorkPlayDrive One the mechanics was saying it’s because there’s nothing in between to absorb the pressure on the valves but he wasn’t sure. I was thinking about ordering the MFER-1 tomorrow, do you think that’ll make the check engine light go away?
@WorkPlayDrive
3 жыл бұрын
It all depends on what’s going on down there. If the actuator is bad you’re better off with the Zautomotive solution. What’s the code?
@ayoFlav
4 жыл бұрын
dumb question. do you do this to both of the sides since it comes with 2?
@WorkPlayDrive
4 жыл бұрын
yep you install this on both sides.
@JB_Kustom
5 жыл бұрын
Hi I had a question about a long term review of your springs with the mfer1 as the springs are exposed to the elements now. Have you heard of anyone having springs break over time or corroding? I recently ordered the mfer-1 and didn’t understand until now what the mfer-1 extreme had to offer.
@WorkPlayDrive
5 жыл бұрын
No issues, but also know that the springs have always been exposed, the original design had openings and a drain hole for any water that got in. I’ll be taking them off the scat pack soon and doing a review. I will cover the spring being exposed.
@JB_Kustom
5 жыл бұрын
Work Play Drive thank you for the quick reply! Your guides are always super helpful
@WorkPlayDrive
5 жыл бұрын
Anytime ;)
@SgtFurby
Жыл бұрын
How does always open exhaust affect MPG?
@WorkPlayDrive
Жыл бұрын
Didn’t notice a difference on the hellcat/scat pack. No logs just didn’t see a difference.
@slomango7927
5 жыл бұрын
I had these for a while but if you use eco mode at all it sounds horrible and drones like crazy in 4 cylinder mode....
@WorkPlayDrive
5 жыл бұрын
I'm glad I don't have MDS (4 cylinder mode)
@slomango7927
5 жыл бұрын
Work Play Drive I actually really enjoy it even though I thought I wouldn’t either....I traded a 6 speed manual car for my 8 speed scat pack and haven’t looked back....
@WorkPlayDrive
5 жыл бұрын
There are a few times racing where I wish I had the a8 but for my commute and driving experience with this car I really enjoy the Manual. 😊
@ramymesiha
5 жыл бұрын
What’s the latest tazer discount code please? - everything mentioned in your other videos has already expired
@WorkPlayDrive
5 жыл бұрын
Discount expired, I should have a new one next month.
@5ohdaddy_95
3 жыл бұрын
So you won’t throw code with this??
@WorkPlayDrive
3 жыл бұрын
If installed correctly it allows the motor to operate as expected and will not cause codes.
@Saab469
3 жыл бұрын
Will this eliminate the rattling and buzzing noise from the active exhaust
@poweredbysrt_savage9456
3 жыл бұрын
I got a 2021 only 3 months old it’s doing it now and I’m trying to fix it it’s getting annoying in the mornings
@Rey-su8eg
3 жыл бұрын
Yes it will. There may be other metal parts under the car that may rattle due to vibrations, but gets rid of the annoying valve noises. Plus, it doesn't kill your MPG like driving in sport mode does.
@WorkPlayDrive
3 жыл бұрын
Yup 👍 what he said 👆
@Guitarist555000
5 жыл бұрын
Awesome! So with my 2015 srt 392 its just a quick bolt on then? Nothing else needed as long as my module has that newer thicker spring?
@WorkPlayDrive
5 жыл бұрын
Yep a few minutes each
@Guitarist555000
5 жыл бұрын
@@WorkPlayDrive hell ya, just what i was lookin for, thanks dude!
@derringercycles
5 жыл бұрын
I remember your video where you put the scope on the exhaust and showed that it stayed open using the tazer in track mode, I'm curious if you happen to know what exactly sport mode does in a scat pack (to the exhaust valves)? There is a lot of conjecture on the forums with people saying that it opens the valves all the time, or sooner, but you are the go to mythbuster in this community so I thought I would ask. I have a manual and it seems like it may be a little louder but it could just be placebo, especially considering that the throttle response is more aggressive which has an effect on the sound as well.
@WorkPlayDrive
5 жыл бұрын
Might be a good idea for me to revisit this one... Once I get the car finished I will add this to the video list ;)
@anoint426hemi6
5 жыл бұрын
I agree with you on manual trans cars being louder. I've had a manual trans scat pack and Hellcat and now have an auto Hellcat and the sound is tame compared to the m6s in any driving mode. I guess it's a quirk? of a automatic. lol. God I love stick shifts....
@WorkPlayDrive
5 жыл бұрын
Same here I really enjoy driving one.
@5ohh3
5 жыл бұрын
is there a left and a right?
@WorkPlayDrive
5 жыл бұрын
The kit comes with 2 pieces, but they can be used on either side.
@ravismaximus7972
4 жыл бұрын
Easier to have a tuner program out as it doesnt have anything with emissions and straight pipe flap out even open that flap creats restriction and turbulence
@oldschoolrichierich4670
5 жыл бұрын
Great video going to get these for my 2016 Scat Pack charger my question to you is if I delete the mufflers with the straight pipe kit I see available online will it throw a check engine light
@WorkPlayDrive
5 жыл бұрын
Nope I have a few friends with a mid muffler delete and no codes. It’s only when you remove the Cats that the O2 sensors will need a sleeve to prevent a CEL.
@oldschoolrichierich4670
5 жыл бұрын
I'm trying to buy the mfrs and for some reason your discount code doesn't work?? I'm trying to buy the upgraded ones because it's funny when I looked at your video my thought was The Xpose spring what eventually rust. When I get them I am going to make some modifications as I think the parts that they put around them there still a little room for improvement. But overall the great product compared to the ones that you hang off of the fucking brake lines how fucked up is that
@WorkPlayDrive
5 жыл бұрын
Code has expired. I will be reaching out to him soon for a new one. Just a heads up the spring are exposed from the factory. There are grooves and drain holes in the assembly around the spring that lets all the elements flow through. My 2015 has been driven in the east coast winter for 4 winters now 3 winters at the time this video was done. As you can see no rust so there is no reason to spend any effort to improve. He created the extremes for people who drive their challengers in the snow, slush and muck. I’m sticking with the standard personally and will of course report back if I have issues
@oldschoolrichierich4670
5 жыл бұрын
Thank you for getting back to me I'll wait to order till you see if you get a new code nice to meet another Jersey Boy I'm actually going to go all the way back to the start of your videos as number one you answered me and number to you make a hell of a video very very informative and thank you for answering me
@WorkPlayDrive
5 жыл бұрын
Thank you. I’ll get to your other questions a little later once the kids are asleep ☝️
@scatpack1073
5 жыл бұрын
Really enjoyed this video, I have a 2018 charger scatpack is the MFER-1 $135 for one or Does 2 come in a pack for $135?
@WorkPlayDrive
5 жыл бұрын
Thank you 🙏. You get 2 in the kit for $135 along with the hardware to install it.
@scatpack1073
5 жыл бұрын
I ordered the mfer-1, but I just seen OCD video, can you tell me the difference between Mfer-1 and the extreme version? I really would appreciate it,
@WorkPlayDrive
5 жыл бұрын
The extreme has a shroud around the springs if you are driving in extreme conditions like mud, slush etc.
@scatpack1073
5 жыл бұрын
Sorry to keep bothering you about this Mfer, I install it and it still seem like the active exhaust is still closing, it starts off loud and then calms seconds after, like usual, Did you get a steady sound level when cranking at cold start, letting you know that it’s open, that’s how I tried to see a sound difference, steady flow lol. or is this open valve only noticeable when driving?
@benramirez4482
5 жыл бұрын
i thought the NoWeeds would do the same thing? so you will have both open?
@WorkPlayDrive
5 жыл бұрын
NoWeeds cuts off the stock exhaust right after the Cats and dumps it out at an obnoxious volume under the doors. I don't generally drive with the NoWeeds open due to the sheer volume of it ;) I use it more for shows. The MFER-1 will open the butterfly in the stock exhaust to make it a little louder.
@justchairsandtables
5 жыл бұрын
I'm still running open most of the time. Can't do it with windows closed
@somejackball
3 жыл бұрын
which kit do i need for my 2020 R/T Challenger, the MFER-1, or MFER-1 Extreme?
@WorkPlayDrive
3 жыл бұрын
MFER-1 is perfect for most installations. If you often drive in extreme conditions like mud, slush or on gravel and dirt roads go with the extreme.
@somejackball
3 жыл бұрын
@@WorkPlayDrive k, thanks!!
@Davvida210
4 жыл бұрын
My active exhaust is hanging from electrical tape etc, sending a CEL to the dash board, any way I could fix it ?
@WorkPlayDrive
4 жыл бұрын
why is it hanging from electrical tape? I would recommend re-assembling it so it's mounted to the exhaust
@Shadow-Banned-Conservative
4 жыл бұрын
Just ordered the kit. Question...Did the car throw any codes after a while? Any issues at all? Thanks.
@WorkPlayDrive
4 жыл бұрын
Nope no codes and no issues at all, just the sweet sound of unrestricted exhaust.
@Shadow-Banned-Conservative
4 жыл бұрын
@@WorkPlayDrive Noice...I agree with what you said before, the stock exhaust sounds great on the 392. No need to spend over a grand on a Corsa or Borla when the stock system is stainless anyways.
@tommynguyen9348
5 жыл бұрын
Hi, thanks for the video. Do you need to make the valve to be in an open position, full a fuse to keep it open prior to the install?
@WorkPlayDrive
5 жыл бұрын
nope, when you turn off the car the resting position is wide open.
@wtaylorhudson3702
Жыл бұрын
Can the plate be installed to lock the valve in the quiet mode?
@transam2000guy1
2 ай бұрын
No
@CarlosHernandez-rb1yt
4 жыл бұрын
I have a question if I disconnect it is the same or what happens
@Wassenhoven420
3 жыл бұрын
it might be the same, but your check engine light would come on.
@bigjojo49er
5 жыл бұрын
When the active exhaust module goes bad does it make a squeal sound, not like a bad fan belt sound.
@WorkPlayDrive
5 жыл бұрын
The squeak like metal on metal is usually the butterfly, the electronic motor strain sequel this could also be the butterfly is stuck or the motor is bad. The easiest way to find out the issue is to remove the actuator and take note of the position, then turn the exhaust butterfly manually to see if you hear the squeak and it should be easy to move with your finger. if it squeaks or it's hard to move you have an issue. If it's easy to move then put it back together and hop under, have someone put the car in run with the engine off so you can hear and see what's going on with the motors.
@lospanditas8023
5 жыл бұрын
That's correct. I took it to the dealership to get it fixed since I still have the warranty on the car. And they just replaced the whole exhaust system. Is there a way for them just to fix or replace the exhaust module without replacing the whole system?
@WorkPlayDrive
5 жыл бұрын
If it’s the butterfly sadly no it’s welded into the rear piping.
@lospanditas8023
5 жыл бұрын
@@WorkPlayDrive That sucks. Thank you for your help! Nice work with your channel
@TowerTruck14
5 жыл бұрын
What if you could just take the butterfly out ? Would they throw a engine light if they were not there?
@jaimefernandez7458
4 жыл бұрын
Do u get extra pops. 😎😎😎😎
@WorkPlayDrive
4 жыл бұрын
installed yep nice pops on the down shift :)
@jojit23
5 жыл бұрын
Love your work. I've install & got this MFER1 (w/updated springs) for my '15 Chally Srt thanks to this video. But recently I got a CEL code p1217. Says active exhaust valve 1. Do you know what could be causing this? Its a new part & I dont think it's broken already. Pls advise. Thanks!
@WorkPlayDrive
5 жыл бұрын
Check your install the code means the valves did not successfully complete their full open and close cycle. Since the MFER-1 makes it easy to see the valves put your phone on the ground below the exhaust valves and record as you turn on the car. Then watch to see what is going on.
@jojit23
5 жыл бұрын
@@WorkPlayDrive the code says "active valve 1 performance. Do you know which side that is? I'll do just that. Thanks again and keep up the good work!
@WorkPlayDrive
5 жыл бұрын
The service manual only states that the p1217 is due to the valve not completing it's full sweep. The system will try every 30 seconds for 20 minutes then on the next key cycle throw the light. It's possible when replacing the spring it may be on backwards or something is bound up.
@MrJohnsl40
4 жыл бұрын
Did you resolve the issue I'm having the same problem. My cel won't stay off
@elanimal305
5 жыл бұрын
hey a question I did a muffler delete to my dodge daytona 2019 ,2 days ago, and the sound, it started in a way that bothers me, but it only sounds when I'm driving but when I'm standing and accelerating it does not sound but when I drive yes, i only need goo 15 mi he star the noise and I want to know if that sensor can produce such sound because they checked the whole muffler and everything was perfect thank you
@WorkPlayDrive
5 жыл бұрын
Sorry can you please give more detail on the sound you are you referring to?
@jwoodard1369
4 жыл бұрын
Are you still running this on your car is so any problems and do you still like it or does it get annoying being loud
@WorkPlayDrive
4 жыл бұрын
Nope not annoying and no issues after the install.
@michaelt2071
4 жыл бұрын
Have u guys had an issue regards your active exhausted. I installed my mfer 5 months ago and now I'm having this issue code p121b.
@WorkPlayDrive
4 жыл бұрын
Nope no issues, check to see if the active exhaust module is making a full sweep when you start the car. Could be stuck or you have a bad module
@mikeprice8307
3 жыл бұрын
Did you find out what caused your P121b code?
@michaelt2071
3 жыл бұрын
I did. I did some test and found out my right exhaust valve actuator not working.i replaced it now no more trouble code. I heard this is common.
Пікірлер: 328