I don't know what he paid but leopard motors are about $100 ,esc are about $120 each , set of left right stingers and flex drives from about $140. hope this helps
@JMSpeck
10 жыл бұрын
It's a beast!! Great work peace RCFL
@zeeek1
10 жыл бұрын
Nice ride! Too bad gel coat broke, lucky it did not get too wet. I may try this setup.
@TheRcEnergy
11 жыл бұрын
Hello Octura X445? There are left / right of Octura only X442 and X447 but you can shrink a X447 (47mm) to 45mm. All of 42mm-48mm is ok.
@dizzychizzy1
11 жыл бұрын
I live in Australia.. would cost me an arm and a leg to get one of thoses rigs... looks sick.
@stats432
11 жыл бұрын
Holy Hell, I'm getting this boat!
@TheRcEnergy
11 жыл бұрын
As described 2x Leopard 4082 2200KV with 2x Seaking 180A, 2x 6s 5000mAh, 2x Octura 447 L + R
@lkeen383
11 жыл бұрын
impressive speed, looking at doing a similar build trying to gather info what size of battery's were you using
@zoxwolf2133
10 жыл бұрын
awesome mate awesome
@TheRcEnergy
11 жыл бұрын
it was very windy that day. It was all ok after crasch :-)
@ijanmotoclubijanmotoclub9039
4 жыл бұрын
amazing speed after run not overheat sir?? that lipo 6s 60c??
@RcBoatArgentina
11 жыл бұрын
thanks!
@guazzoa1
9 жыл бұрын
hi, Can you tell me what is your receiver? please. Because I do not want to make a hole for the cable of the receiver so I would like to know what are you using receiver. Because I am worried That That since the hull is made of carbon-kevlar i can have some problem of reception
@TheRcEnergy
9 жыл бұрын
guazzoa1 I use the CCX Pro Jamara without dying antenna for mice to perform .
@MRTWINTURBO88
11 жыл бұрын
Hi, I have been contemplating using this hull for a while now. I want a setup similar to yours. If you don't mind me asking but how much did this setup cost you?
@TheRcEnergy
11 жыл бұрын
The controller is set to 1: 1, 2:1, 3:4, 4:5 are I think the standart values
@RcBoatArgentina
11 жыл бұрын
please can you tell me the setup for the 180a esc do you use? thanks
@mooen83
11 жыл бұрын
i have a tips, try 2X tp 4050 3250kv 18v 3200w, 2x 180a esc, 2x 4s a spec nanoteck 5000mah, and 2x 642 octura. you take that speed.
@pixelus973
10 жыл бұрын
nice !!!!
@RcBoatArgentina
11 жыл бұрын
Yes, but how do you set the 180a esc??? Item 1: 1 / item 2:6 .... thanks
@dizzychizzy1
11 жыл бұрын
mission accomplished! how did it pull up after the crash?
@amisol4995
7 жыл бұрын
hello again, what timing do you suggest on leo 4082 2000kv, seaking 180a v3 and 6s?
@daiciuapostol79
2 жыл бұрын
answered late15°😁
@amisol4995
7 жыл бұрын
Hi there. Do you still have this hull? I´m going for 2 x leopard 4082 2000kv, 2 x seaking 180a v3 and to start with alu props 2/444 r+l, and of course 6s on each side. Any thoughts?
@TheRcEnergy
7 жыл бұрын
I still have, yes that is ok. Think you get to 120 km / h
@amisol4995
7 жыл бұрын
Thanks for reply. Do you think think I could go for cnc 2/448 props? And noticed you replied quoistion regarding bullet plugs. I have the original leopard 6mm bullet and original seaking esc 6mm bullet. Is that OK?
@TheRcEnergy
7 жыл бұрын
yes, no problem
@amisol4995
7 жыл бұрын
Okay, now my boat is ready. Only wondering. What do have on the timing on your motors? I have 200kv less than you. Any suggestions?
@danielmomesso6377
7 жыл бұрын
hey, i use an octura X447 on my rc boat, there amazing!
@TheRcEnergy
11 жыл бұрын
My next setup in 2x 4050 L 2350KV and 3600 watt 2x 180A at 2x 6s 5000mAh x450 LR for 160 Tip : the L have more Power 3600Watt !!
Пікірлер: 34