I was watching your video on lg multi video unit that u were starting up with Manny in Dallas area. Great video!
@EdenGPerez
3 ай бұрын
Cuídate mucho de el calor y el alto voltage soldado
@MannyFrezco
3 ай бұрын
Wow your amazing ❤
@topher8634
8 ай бұрын
A little bit of alcohol in micron gauge will usually correct inaccurate readings.
@simonbernard7409
16 күн бұрын
You should press the calibration button on the micron gauge to fix that problem
@scottriddle5468
9 ай бұрын
Good job brother
@craig1611
Жыл бұрын
Works better if you put a slight vacuum on the system
@Charles-nd4yr
Ай бұрын
Pul a little vacuum next time and it will be easier
@jeffgrant6914
Жыл бұрын
Great video buddy 👍
@FrostHVAC
Жыл бұрын
Man I don't repair aluminum coils, i'd be scared of that call back. I've seen guys repair them and quote out the coil to be replaced regardless. So if the customer denies it, it's not on us
@zaccody6980
Жыл бұрын
Really impressed with coil repair. I've completely destroyed coils before trying to do the same thing. Glad to see you putting out content again man keep on trucking
@luiscorr2190
Жыл бұрын
The microchannel is a product to reduce costs in a fight against the competition, and the manufacturers know it.
@xraybravo7180
Ай бұрын
So i had siimiar hole on aluminum coil but it was facecing down as i cleaned it and i heated up with mal gas it was hard to bring it to teno then when it got temp it would stick.
@mriederer
Жыл бұрын
Glad your back. Really enjoyed your supermarket videos. I just recently picked up the field piece micron gauge when my blu vac was misbehaving. Really happy with the FP so far
@shine-cg9uf
Жыл бұрын
❄️💪👍🇺🇸
@hvac_audaz_firme
Жыл бұрын
Nice & easy, low (heat) & Slow tis was shaky but very satisfying braze (or soder?) Bummer about the micron gauge. Always a great day when you upload Rookie
@-757-
Жыл бұрын
Good to see you back at sharing vids
@drodriguez394
11 ай бұрын
Clean them w rubbing alcohol
@nickproline8382
11 ай бұрын
Big Dawgggg 👍💪🏽
@Justintime631
Жыл бұрын
Great repair. As long as it’s holds, good to go.
@WhiskeyTangoFoxtrot711
Жыл бұрын
Do you think you could make a helpful video for the basics for sequence of operations on most walk in coolers or helpful tips for making wiring easier.
@SaidSuil
Жыл бұрын
Hello man, nice job, just one thing, when removing the old filter, if you braze it you are spreading all humidity that may be trapped in the core into the installation, I know it's a lot easier to unbraze and braze. I read in Danfoss installation manual for refrigeration technicians along with many other tips.
@rookierefrigeration4357
Жыл бұрын
True but I think it’s minimal. Especially when you’re still pulling a vacuum.
@Oz_is_on_fire
Жыл бұрын
Prematurely feeding the rod. Happens to the best of us 😂😂😂
@FatManFishing
5 ай бұрын
Im a electrician (not a HVAC tech) am i having issues understanding how to hook up a couple new trenton condensor units. Is there a way i can contact you or you could contact me?
@OnePointLander
Жыл бұрын
You know NAVAC sucks when you have two identical products and they both are broken.
@805HVACR
Жыл бұрын
Key thing was that your solder stuck. Being rusty is all good. I’ve only soldered on aluminum 1 time and it was horrible but it held lol.
@WswRefrigeration
Жыл бұрын
That’s the thing with all these damn micron gauges. How do you really know they’re reading right?
@rookierefrigeration4357
Жыл бұрын
Exactly
@matthewclemons1574
Жыл бұрын
Likely oil or contaminants on the sensor of your micron gauge. Try cleaning it with alcohol 8:41
@HamiltonMechanical
Жыл бұрын
great to hear from you buddy!!
@brenta1905
Жыл бұрын
Filter first, no. You acknowledged the possibility of replacement if the repair failed. Why waste a filter. Good job. Real work, not theory.
@sherwinalvarez7365
Жыл бұрын
You may have exposed it to positive pressure. Clean with mineral spirits. If that dont work warranty, then use the bluvac. Its better.
@HVACOG
Жыл бұрын
You did well dude 😊
@LarrydWoodruff
Жыл бұрын
Keep ‘em comin brother
@TheSimba86
Жыл бұрын
you might need to clean the sensor of the micron gauge with alcohol
@Patrick-hq7sq
Жыл бұрын
2 smokes and coffee vacuum time is better than no vacuum 😂
@rookierefrigeration4357
Жыл бұрын
😂😂
@gtownhvac1640
Жыл бұрын
Try the fieldpiece vacuum MG44
@ryanisaacson118
Жыл бұрын
This is why i hate micro channel
@chris84662
5 ай бұрын
Micron gauges are a waste of time and money.
@MaxStax1
Жыл бұрын
I used to do stuff like back in the 80's when i was new. But i learned it's better for the customer and everyone involved to just replace the condenser. Are the customers welfare bums? Charge for a new condenser coil ! As anyone at the factory will tell you, and i have talked to them many times, that is a defective coil and other leaks are probable . I guess the maintenance guy is an illegal who should be deported so you couldn't film him. Worthless undocumented workers from Mexico give the HVAC trade a bad name.
@jonnyjonnyyespapa8013
Жыл бұрын
Lol are you serious??? 🤣 😂😂
@zaccody6980
Жыл бұрын
Dam bro putting out a lot of hate right there. Comments like this should be kept to yourself
@BluOrangeJuice
9 ай бұрын
He shows his face in the video and documents his experience on his entire channel. And who cares what you think is better? Not everyone can afford it, period. Keep your ignorance to yourself.
@shadowbanned69
Жыл бұрын
Take the gauge..put in freezer 30 min. Next put rubbing alcohol inside the sensor cap. Shake with finger...blow out with low pressure nitro and shake every 30 sec. Try to use again. If it won't work...replace it, sensor is bad
@luiscorr2190
Жыл бұрын
The microchannel is a product to reduce costs in a fight against the competition, and the manufacturers know it.
Пікірлер: 47