Great job thanks.....the check valves are cupped though make sure the green/blue strip is up.
@605BOLT
Жыл бұрын
Yes. I didn't see any cup on mine but def that's the way to do it. I will pin your comment in case anyone misses that. Thanks for the kind words!
@insanevtec9200
Жыл бұрын
Great video! Will help out with my carb rebuild this weekend! Thank you !
@605BOLT
Жыл бұрын
My pleasure. Remember to stay hydrated! 🍻
@neppy5
11 ай бұрын
@605BOLT thanks for this video! you explained things so clearly and great close ups/camera angles and everything, easily the best rebuild/pop off video i’ve come across and i’ve been using it as a guide to rebuild my dual carbs on an xlt 800 basically identical setup to yours i’ve got this baffling issue where i can’t build pressure above 40psi during the pop off test, i have the same tester and it goes past 100psi with just the hoses blocked off up to the carb inlet, don’t see any signs of a leak in the needle/seat, no bubbling, really at a loss as to why it won’t build up higher pressure
@605BOLT
11 ай бұрын
I have another video coming out later where I needed to adjust these settings. It had a bog off idle that I couldn't fix. I got a bigger needle and seat and pulled pop off back to 45 and it cleared right up. Assuming it will help you too. Thanks for the kind words. Could be not building pop off because the needle and seat are wore out.
@neppy5
11 ай бұрын
@@605BOLT thanks! i’m subscribed and looking forward to that video. My needle and seat is actually brand new oem mikuni, and i used the oem rebuild kit as well. Decided to think out of the box a bit and found that air is actually leaking from the other side!! (pump side?), so weird, i tightened up the screws but it’s still leaking, made a short video of it kzitem.info/news/bejne/2o99qJuNcaeXoaAsi=xZu5CcGbfQNIXnoN the carbs are from 20 year old machine, wondering if they’re still fit for service
@605BOLT
11 ай бұрын
@@neppy5 I'll check it out.
@alfredorodriguezjr8660
4 ай бұрын
Hello my guy..... Greatly appreciate your videos I might be needing some of this information in the near future
@605BOLT
4 ай бұрын
Thank you for the kind words. Ultimately I hope you don't need it!
@alfredorodriguezjr8660
4 ай бұрын
@@605BOLT you see the thing is I just picked up two free jet skis 1996 Kawasaki one of them is a 900 the other one is 750... They've been sitting for a few years... I'm going to start working on them seeing if they run
@605BOLT
4 ай бұрын
Right on. Sounds like a score!
@richardanderson8588
Жыл бұрын
Great video bud/ Your hose to the Accelerator pump has a check valve inside it. Do not throw away the hose. look inside for jet style check valve. Reinstall it! I set my Pop off at 35 psi
@605BOLT
Жыл бұрын
I just went and checked the hoses. I actually kept them. No check valve😬. I wonder what is going on there?
@kyleroman9326
Жыл бұрын
@@605BOLTI just checked my 98 gsx l (5625) none either
@605BOLT
Жыл бұрын
@@kyleroman9326 idk then. 🤷♂️ I'm glad you commented though because I feel like people will be curious
@EEI605
Жыл бұрын
Nice. Liked the video
@605BOLT
Жыл бұрын
That was a crispy pop off though.
@vitaminp579
3 ай бұрын
Just found this...Thanks. it's helping me out big...One question...If you kept the same spring and needle, how did the pop off get to 80 psi? What changed? Thanks ..
@605BOLT
3 ай бұрын
Idk. That's why in the next video I ended up changing some pieces around per sbt. It ran on plane ok but wouldn't hole shot well.
@AchikSarih
4 ай бұрын
Merci beaucoup ❤❤❤❤❤❤❤
@605BOLT
4 ай бұрын
You're welcome.
@guerosern
Жыл бұрын
Cool 😎
@605BOLT
Жыл бұрын
🙏
@omerbbM5
5 ай бұрын
13:25 The gasket and plastic sheet in the picture on amazon is not the same as yours
@605BOLT
5 ай бұрын
True. But it's just a picture. As long as you get the Mikuni kit you're good.
@nickmocilan9067
Жыл бұрын
Do I have to adjust the idles and lows and highs or if they look right then don’t even touch them
@605BOLT
Жыл бұрын
If possible, don't mess with them. If it runs, leave it.
@605BOLT
Жыл бұрын
The settings are highly dependent on where you live and any mods or not.
@nickmocilan9067
Жыл бұрын
@@605BOLTI got my needle and seat out but then that the 2 screws to get to the jets it looks like the last people who did it stripped them pretty bad any ideas how to get them out?
@605BOLT
Жыл бұрын
@@nickmocilan9067 shoot that's gonna be tough. Could try cutting a little slit in the screw to make it a flathead. Might work. Otherwise just leave it maybe. That's from somebody not using those Japanese screw drivers I bet.
@nickmocilan9067
Жыл бұрын
@@605BOLTI ended up drilling the head off real risky but worked out thanks for the help though
Пікірлер: 37