Brilliant in all the ways, a true professional. Thanks alot for all your lessons here! Respect for your modesty, explenations and and calm way of teaching. Keep it up!
@wrestler4life521
28 күн бұрын
Thanks for the video. I thought soldering Lithium batteries was a no no and could damage the cells. Any reason not to spot weld them instead?
@Paul-IE-Repairs
28 күн бұрын
Ive had to repair factory spot welds, with solder. As long as you dont overheat them its fine. I do have a spot welder now i just need time to get it setup. Also with spot welding ive seen dewalt batteries that over penetrate and blow holes in the end caps
@wrestler4life521
25 күн бұрын
@@Paul-IE-Repairs I see. Thank you for the feedback.
@mesranhobbies3799
Жыл бұрын
terbaik informasinya...
@daniellappin2191
Ай бұрын
Thanks for the video. I have a question: It looked like you were recharging those two new cells using/thru the battery pack. So all of the cells are receiving a charge when you really are only suppose to charge the new cells so that they are balanced before connecting the actual charger. This is so the other cells don't get overcharged trying to bring the new ones up. I'm trying to learn...Is my thinking correct?
@Paul-IE-Repairs
Ай бұрын
Yes, you are correct, before you put them on the charger they should all be within 100mv of one another. If not it will thrown a cell error fault
@daniellappin2191
Ай бұрын
@@Paul-IE-Repairs Thank you!
@georgeg8130
2 ай бұрын
Awesome video. I have question about 18650 battery brands. Does it have to be exact brand and model or just 18650 with same specs? What you recommend?
@Paul-IE-Repairs
2 ай бұрын
You can mix and match, as long as they charge and discharge at the same rate
@georgeg8130
2 ай бұрын
Thanks!!!
@TacticalThib
Жыл бұрын
Why is the 2804-20 starving for power with these 5.0 packs of you've ever tried to use a 5.0 4.0 3.0.. the drill will surge and make a weird noise is it the motor starving for amps under load??
@Paul-IE-Repairs
Жыл бұрын
What you are describing sounds like the Pulse width modulation doing its job, there is firmware in the tool and the battery that communicate and adjust accordingly for optimal tool and battery life
@TacticalThib
Жыл бұрын
@@Paul-IE-Repairs thank you for clearing that up I always wondered why it did studder with anything lower than the 6.0 high output battery under heavy load. I appreciate you reaching out...
@halbrookins38
Жыл бұрын
Impressive but confusing.
@gmarine357
Жыл бұрын
I have a 5.0 that died after use. No lights on indicator. Flashing charge.
@Paul-IE-Repairs
Жыл бұрын
you may have burned out the fusible link on the positive bus
@spinnanz
Жыл бұрын
You'd be best to get spot welder to weld those cells in. A $25 welder will be far better than a $150 soldering iron.
@Paul-IE-Repairs
Жыл бұрын
its on my this of things to make, but I work 7 days a week and average 75hrs
@rscrubc300
Жыл бұрын
Can i send you a 12 ah pack to fix?
@Paul-IE-Repairs
Жыл бұрын
unfortunately I don't have a PO Box rented for people to ship stuff to me for repairs at this point.
@davekleiboeker4614
Жыл бұрын
Shipping lithium
@user-tt8zn5ss7s
Жыл бұрын
I need to know the reason about my battery have 21.3 v ,but it can't work. How can I do?
@Paul-IE-Repairs
Жыл бұрын
you may have blown a fuse, or the BMU module is bad, is there any flash errors when you push the fuel level button?
@user-tt8zn5ss7s
Жыл бұрын
@@Paul-IE-Repairs In this case I should be change Bms of my battery, yes or no?
Пікірлер: 36