M18 Red Lith XC5.0 I jad the same problem. Tried this and it worked. I only left the batteries connected for about 30 seconds. Thanks for the fix! Saved me from dealing with Milwaukee.
@203isaiah7
11 күн бұрын
Worked for me! Took 1 minute
@rvz77
5 күн бұрын
Milwaukee customer service is absolutely 💯 HORRIBLE. Either you pay to ship it in or you go back to the store you bought it from. A BRAND new battery! I will try this, thanks.
@robertthomason8905
28 күн бұрын
Just started working at a heavy diesel repair shop. I noticed many chargers and batteries out of commission. Deap pockets just buy new batteries and chargers apparently. Thank you for the information.
@AccuracySpeaks
27 күн бұрын
Congratulations on your new job! What is your area of expertise, everything?
@rvz77
5 күн бұрын
@@AccuracySpeakshe must be Jack of all trades.
@akkalachhab8547
Ай бұрын
I did it and it worked the only difference is I used a battery maintainer, thanks.
@robertsalasidis7695
22 күн бұрын
Worked on mine - I have a variable power supply - put in 18V 1A max, and in 20 seconds the voltage went up to 11V, with one blinking light on the battery pushbutton LED display. Plugged into the charger, and it worked great
@kaceydavidson
Ай бұрын
That worked great! Thanks for the video! It brought my xc4.0 back to life after leaving it in my sawzall for too long.
@AccuracySpeaks
Ай бұрын
Sweet, glad it worked for you!
@edgardmartinez6026
3 ай бұрын
Wow this shit worked!!!! I had nothing fancy like you. So I used a coax cable stripped it to the wire made two small cables for positive and negative waiting 8 minutes and boom!!! Thank you
@user-uo9sr2vs9r
3 ай бұрын
I did this trick with my m18 battery. It worked!! Thank you for the Video!
@AccuracySpeaks
3 ай бұрын
Excellent, I'm glad it helped you out!
@jayjohnson8613
3 ай бұрын
I had the exact same problem, and i did the same steps you showed here. It worked perfectly!! You save me $$.. Thank you so much!!
@AccuracySpeaks
2 ай бұрын
That's awesome, glad it worked for you!!
@kaceydavidson
Ай бұрын
That worked great! Thanks for the video! It brought my xc4.0 back to life after leaving it in my sawzall for too long.
@pointnozzleaway
7 күн бұрын
You should NOT have to do this for a new 1 Bar Battery. Thanks for the info 👍
@LeoDodier
2 ай бұрын
Thanks...IT WORKED and you saved me from buying a new one!
@AccuracySpeaks
Ай бұрын
Sweet, glad it worked for you!
@mon3starb122
Ай бұрын
I owe you a beer good sir !
@AccuracySpeaks
Ай бұрын
That'd be cool!! Glad it helped you out!!
@ginalt311
7 күн бұрын
Thank you! Worked for us as well. What a dumb design…well smart if the intent is to force people to keep buying replacement batteries
@shapat09
Ай бұрын
Awesome. This worked great! Thank you!
@AccuracySpeaks
Ай бұрын
Excellent, you're welcome!!
@janghyuk8636
3 ай бұрын
I just did this and IT WORKS! my XC5.0
@AccuracySpeaks
3 ай бұрын
That's awesome buddy!!
@mrbrummitt1
14 күн бұрын
Worked for me....took about 30 seconds but be careful, my jumper wires got a little warm
@andrewramirez7087
Ай бұрын
Worked on a h.o. 6.0 Thanks for the info
@AccuracySpeaks
Ай бұрын
Awesome, glad it worked for you!!
@marksanson6788
2 ай бұрын
This is awesome, thank you! It worked for me.
@AccuracySpeaks
2 ай бұрын
Excellent, glad it helped you out!!
@haroldpruitt8207
15 күн бұрын
Much appreciated!!👍
@betorocknroll9400
2 ай бұрын
F.... this work with my battery.. thanks buddy..👍👍👍
@boricua77
10 сағат бұрын
I got a dead battery for let the battery charge off several time using the miwakee fan
@patricktokozer9848
25 күн бұрын
Merci la mienne était plat sans charge du coup il s'allume rouge et vert, je fais la même manipulation sa à marcher !!! Merci
@AccuracySpeaks
25 күн бұрын
That is great, I'm glad it was able to help you out!
@Star-Destroyer
2 ай бұрын
But you need a second milwaukee battery to make this work? Is there a different battery i can use as the power source?
@AccuracySpeaks
2 ай бұрын
I'm sure there is if you know what you're doing. I do not know a great deal about electronics, so I don't want to tell you something that can ruin your gear or hurt yourself. I'd imagine if you have a battery with the same or similar voltage you could probably excite the cells enough to trick the charger. As far as I know, all you're doing here is tickling the cells with enough charge to show at least a little charge on the battery so the charger will recognize it is a battery. If you go to throwing too much amperage or voltage to an electronic device, I do know you have the potential for bad things to occur like explosions, fires, and possibly injury, so be careful! If you've never had a battery blow up on you, I'll tell you this, you don't want to! I witnessed a truck battery explode one day many years ago on my Dad's old 70's C-10 Chevrolet. If you would have been working under the hood when that damn thing blew, it would have killed you without a doubt, it was about like a grenade going off, it was a hell of an explosion, one I hope to never witness again!
@RaptorEyeWRX
Ай бұрын
Will this work with the M12 batteries? My XC6.0 is doing the same thing.
@AccuracySpeaks
Ай бұрын
I'm not an electrical engineer, so I cannot positively answer this, however, I'd say it's possible. If it were me, I'd be careful and use similar voltages... I have an automotive charger with this so-called "smart" technology that I have likely replaced several perfectly good batteries because the charger wouldn't charge the battery! I feel this is no accident, they want to sell batteries!
@timgebers2858
Ай бұрын
I bought a 2 pc combo drill and driver pack from home depot that came with a 3rd battery....after trying the insert and remove 20 times (only guidance I got from milwaukee) it still didn't work....I'm going to try this with 1 of my other batteries and see if my 3rd battery just is too dead to charge, I sure hope it works.
@AccuracySpeaks
Ай бұрын
Hope it works! Yeah "OLD Milwaukee" isn't going to tell you anything, they just want your money!
@cleanhonda333
11 күн бұрын
I have a brand new M12/M18 charger, model 48-59-1812, that seems to charger the batteries OK, but the area above the port for the M18 gets so hot that you can smell melting plastic. Has anyone else experienced this? If so, was there a way to correct it other than sending it to Milwaukee for evaluation?
@AccuracySpeaks
11 күн бұрын
If it's brand new it would for sure be under warranty. If it's getting that hot, I'd recommend not using it and contacting them, I'm sure they'd gladly get you another charger out to you, you certainly don't want to burn your house down! To answer your question, I have never experienced the situation you are.
@kevinreeves3161
6 күн бұрын
You got one battery that’s real
@MarcialR4
21 күн бұрын
Helloo, where i can find the cables?
@AccuracySpeaks
20 күн бұрын
I made mine with about a foot of speaker wire and crimped on 4 spade connectors. If you don't have any wire laying around, Radio Shack, if they even still exist, would have some wire, or a car stereo shop would probably have some. They may even throw you a jumper together if they were cool if you asked them...
@calonstanni
Ай бұрын
I don’t have another tool battery to hook my dead battery to. Can I use a trickle charger or my car battery?
@AccuracySpeaks
Ай бұрын
Someone in the comments said they used a maintainer to trick theirs, however, I haven't tested it, nor can I confirm it. Just be careful!
@calonstanni
Ай бұрын
@@AccuracySpeaks um...I have no experience with stuff like this. I'm a 61 year old cat-lady. What should I be careful of? BTW...THANKS SO MUCH FOR RESPONDING!!!😘
@AccuracySpeaks
Ай бұрын
@@calonstanni putting too much voltage or amperage into batteries and such can cause some nasty things to occur. If you do things incorrectly, you can have a battery explode or possibly a fire, and you don't want that to occur! I'd ask a friend that is handy for some advice. As far as responding, you're certainly welcome! I'm sorry I can't tell you anything with certainty. Check out a comment below from a viewer that stated that they used a battery tender.
@Ram-li9wt
Ай бұрын
it melt the cables
@kaufmankdk
Ай бұрын
Battery Issue. The Fix is Place a Jumper from bad battery to a good charged battery. Pos + to Pos + and Neg - to Neg- terminals wait for about 15 minuets for battery to equalize. problem solved. both batteries are ready for work or charge to full
@gonzalezt7081
Ай бұрын
Yea it will work now sell it! Some wrong with the battery anyways
Пікірлер: 58