After watching, I took a flat head screwdriver and a hammer. Place screwdriver where blade goes. Turn flathead so it doesn't go into slot! Hit hard once or twice. Fixed!!!! Thank you for your help!
@davidortiz3061
10 ай бұрын
Holy crap it worked!!! Thanks bro!!
@davidfleuchaus
6 ай бұрын
Easy as pie? No! Way easier than that. Easy as hammering the flat side of a screwdriver placed on top of shaft that the blade goes into. Tap tap. Tap tap. Working again. Thx for the tip.
@darrendebrun1074
5 ай бұрын
lol I smacked with a socket extension and it worked 😂
@richardsonsilva1412
4 ай бұрын
lol you the man . Thank you
@downtourth
Жыл бұрын
Awesome thanks bro! I just squirted oil down the tip and banged on it with my channel locks, it started working again. I'm a plumber so mine seems a lot of water and dirt, I'm surprised it still works. Glad I didn't have to take it apart thanks again
@idigit7142
3 жыл бұрын
Thanks for your video, I’m glad I watch the whole thing before I started disassembling. We just hit the end with a hammer! Thanks again!
@mitsumike714
3 жыл бұрын
I was thinking the same thing
@engjds
3 жыл бұрын
My thoughts exactly), sometimes an hammer is the best solution.
@jimferreyra2709
2 жыл бұрын
That large torx nut on the side underneath the cover will turn the motor which in turn will free up the shaft, I used an impact driver with a T-40 torx driver bit
@ianosborn5811
2 жыл бұрын
Thanks! This saved me from taking the whole thing apart
@johnnyconrad4859
Жыл бұрын
Great video Mine did the same thing Bought a new one Monday, I'm gonna try your method
@jimferreyra2709
2 жыл бұрын
The large torques bolt on the side underneath that cover will turn the motor over that’s what it’s there for so if you just take a impact driver or even just a a socket wrench with a T 40 torques driver that will turn the motor over and free the shaft it
@johnvetter.7209
2 жыл бұрын
Thank you so much.good video God bless you and your family!!!
@White000Crow
2 жыл бұрын
I forgot mine out in the rain for a couple days and today it finally took a poo. Time to rebuild.
@xINvAdeZz
11 ай бұрын
mine did the same thing. Big flat head down the middle and a knock with a hammer free’d her up. Thank god I didn’t pull it apart
@ShrimpTechStocks
2 жыл бұрын
Hope this will fix mine cause it's the same problem
@clemmtec9506
2 жыл бұрын
Just use a pice of wood on the head were you put the blade and tap it in and spray wd40 that is how i fixed mine after seen this video, Mine is working fine again.
@Mr.Pop0
3 жыл бұрын
my old man was using mine to cut pipes that had water in them, it rusted shut gonna try to fix it nyself.
@clemmtec9506
2 жыл бұрын
wd 40, and a tape on the blade , don't take it apart
@vdlc84
3 жыл бұрын
Good stuff
@zakaroonetwork777
Жыл бұрын
I just bought this saw and the pivot shoe is jammed. Im going to cut my project then return it an get the older model for $80. Less
@bainsworth8853
3 жыл бұрын
you pulled that off wrong, it wiggles straight off only a small screwdriver to get boot over blade lock mech
Пікірлер: 27