Thank you very much for your comprehensive video!!! I received my sakura today and I'm going to attempt to assemble it.
@knicklicht7945
2 жыл бұрын
I have this model partially build in the basement for about 8 years, its badsically the same as your one. I might pick it up again.
@avijitsadhukhan8371
3 жыл бұрын
Good one. Love your channel.
@Joyplanes
3 жыл бұрын
Thank you very much!
@americanbrandon
3 ай бұрын
Damn that music at at 1:15 is 🔥 I was totally staying to freestyle in my head 😂
@americanbrandon
3 ай бұрын
Check it!… I’m flying my RC plane Im flying every day Birds trying to take me down but I chase them away! What 😂
@balfasladicra5270
3 жыл бұрын
First From Indonesia!
@angelrc9869
3 жыл бұрын
Good job,Ilike 3d airplane.
@sajalacharjee7008
3 жыл бұрын
That's super cool
@fc1133
2 жыл бұрын
Thanks for posting...
@wjsbruwer8206
3 жыл бұрын
I love when you upload a vid about a micro rc planes ;)
@user-bj8bi2ku8z
3 жыл бұрын
初めまして、素晴らしい❗公園で楽しめる飛行機ですね。私も注文しました。
@suji99hettiarachchi
8 ай бұрын
Hello, I received this kit version(without any electronic) of E010 Sakura airplane from AEORC factory so I weight the overall body parts of the package included all items but excluding the instruction manual, the weight was 38g(grammes).I searched every where to buy likes this UHU por type of glue but unfortunately, the oversees air transportation doesn't support to ship the glue items through the air. Hence I measured the weight of just only one stick of glue gun stick, it was 10g(grammes) so I asked from the factory that will it fine to use the Hot melt glue for reinforce the parts of this airplane so they said that if I used the hot melt glue the aircraft overall flying weight will be increased so as the result, it would be hard to fly, hence use a specified glue for foam. I am using very light weight electronic components like 2g servos, a 1106 brushless motor with prop saver and a 5030 propellers and a 8g of weight ESC, with a ELRS micro receiver and this Byme A flight controller ,I just prefer to build this model to fly on 1s(3.7v) and so far the motor unit can trust 165g in weight when supply 2s power, therefore if I prefer to build this airplane in 1s(3.7v) power and with using the hot melt glue for reinforce the parts , will it fly fine without any issue?
@anthony3D
3 ай бұрын
De la colle blanche (colle a bois) ça marche aussi mais le temps de séchage est plus long.
@vanditsharma6100
2 жыл бұрын
its cool how it looks like an f3p slow flyer but it flies fast
@suji99hettiarachchi
8 ай бұрын
Hello, I couldn't find the UHU brand POR type of foam glue to reinforce the parts of this airplane, therefore is it okay to use Hot Melt Glue in medium temperature to reinforce the parts of this airplane?
@haokaixuan
3 жыл бұрын
First, cool! 😃
@dzar2230
2 жыл бұрын
I love this video
@Maurice419
2 жыл бұрын
You can get foam safe CA glue.
@sametguler6769
3 жыл бұрын
Çok iyi bir proje eline saglık
@josedavidbanegasalpiri7953
3 жыл бұрын
Hello Joy vas a subir el mismo video al otro canal no
@gtjumper
7 ай бұрын
It's tailheavy
@radekjakl186
2 жыл бұрын
Your troubles with motor loks me like bad timing setup. You can reed manual which was suplied with ESC how to setup higher timing. Very simple procedure just listen beeps and moveng throtle up and down based on count of beeps. I bouth it as well and it works well. I am just little bit disapointed that servos are quite slow. Whole system works on low voltage 4.7v. definetly it will be improvizace to run it on 6v but it means diferent esc may be receiver as well. Or buy better servos. Both ways are dificuilt and expensive for me so i set it up to use just part of servo stroke(70%). I lost resolution and force but gain speed i hope it will be ok. Enjoy flying bye R.
@bruvbruvbruv6191
3 жыл бұрын
Plz make a slope souring wing
@ninjapicklez69
Жыл бұрын
I wonder if anyone's used lighter weight 1s electronics. A 1203 6200kv has about 70g of thrust on a 5030 prop @3.8v
@easy_3d
2 жыл бұрын
What is the AUW? And also what receiver did you use? Can you send me the instructions manual photo, i want to build one by myself.
@rc_models23
Жыл бұрын
Is the Akku in the der too
@johnmarktamano8834
3 жыл бұрын
Have you tried those indoor slowfly planes?
@notaprofessionalneonazi2157
3 жыл бұрын
WAIT? There are 2d rc planes?
@torinkyemba647
2 жыл бұрын
I guess so lol
@kxdmotovlog6898
2 жыл бұрын
if i have flysky i6 remote control and his receiver this plane work???
@purplefurture6960
Жыл бұрын
for beginners?
@aaamodeltrainsandplanes3774
2 жыл бұрын
Does it have any type of stabilization in the receiver to get it out of trouble when needed ?
@mixed_by_pgee
2 жыл бұрын
Nope, I don't think so.
@mustangxxmatty3106
Жыл бұрын
got one in and motor wires were ripped out of motor with no way to solder back on and the carbon was wrong size ..!!!!BUY AT OWN RISK
@panosth4th441
3 жыл бұрын
where are you from
@MartyLJ57
3 жыл бұрын
Too bad radios don't come with the plane
@masamokish9184
3 жыл бұрын
Why it is bad? I think it wouldn't be very comfortable if I had got 10 planes and also had 10 radios, what if I lose one of them or something else. I can buy only one radio and fly with every plane I want. Also, now radios doesn't cost a lot: radio, that was featured in the video (FlySky FSi6) right now costs only about 50$.
@antoniorausa9695
2 жыл бұрын
@@masamokish9184 I have it, and it is awestome
@alejandrosanchez6782
3 жыл бұрын
Where can you buy it ?
@dzar2230
2 жыл бұрын
At the description
@mandydoncansil9606
3 жыл бұрын
where I can buy tht sir
@masamokish9184
3 жыл бұрын
There are links in the description. You can buy it in Banggood, Aliexpress or somewhere else
@F3AFlyer05
3 жыл бұрын
Plane is way to small if you have a biger plane around 80cm span you van fly way better and you van hover better
Пікірлер: 51