S2 chassis as FM chassis is so out of the box idea. the stability and speed of this build is insane. Excellent build bro!! The problem: I couldn't make the motor backward without open the motor seal.
@izukieternalart
4 жыл бұрын
damn that stability and speed
@19kievanruz86
6 жыл бұрын
very nice setup bro
@afifsyaifuddin9001
Жыл бұрын
The best of tamiya... 👏👏👏👏👏👍👍👍👍👍👍👍
@galihargo6997
6 жыл бұрын
Hi dude your video is great , i have a question, do you need body damper to become competitive? Are there any alternative to it?? Thanks
@ernelperez5731
7 жыл бұрын
Hello sir can you make a video how to make a sliding damper for VS chassis, thanks po
@alwizh9656
Жыл бұрын
Nyimak kak..aku mau belajar
@not_riley
6 жыл бұрын
Would there be a noticeable difference if you used a rigid set-up on a track with a single digital turn section such as that one?
@Z3NBluster
6 жыл бұрын
I've seen results that the times don't really improve. They're fairly similar. But what happens most of the time is that cars that do not have sliding dampers that are being run alot on digital curves have a higher chance of breaking apart. Cars with sliding damper are more durable in situations like this.
@alfredovaldez1173
6 жыл бұрын
Is there an tutorial of yours for making sliding damper? TIA
@antjosh4507
5 жыл бұрын
Hi zen, does the at bumper, pivot, and sliding damper have a distinct advantage over rigid plates in standard Tamiya racing tracks. Thanks
@Z3NBluster
5 жыл бұрын
What do you mean by, "standard?"
@user-ey7by7lh3b
7 жыл бұрын
Cool!!
@Z3NBluster
7 жыл бұрын
GaИeme mini4wd Thanks
@greenberry6464
5 жыл бұрын
bro can u rebuild this car..its to cool for as ..can u,, plzzz 🙏🏻🙏🏻🙏🏻🙏🏻.. im your fan from malaysia
@Jermeister
6 жыл бұрын
I’ve run 19mm rollers on the front, 7+ degree angle but it isn’t very consistent on clearing the bridge Lane Changer. Had to resort to the 12-13mm rollers on the right front. Are your front brakes set quite low? Mine’s at a 2.5mm to tackle the high banks..
@Z3NBluster
6 жыл бұрын
If you're not clearing a lanechanger with 5 degrees, its probably one of two things. There are probably very many straights before the lanechange giving you alot of run up to it. Or your rollers aren't biting properly. I do not have a set height on my cars. I change the setup depending on the track.
@Jermeister
6 жыл бұрын
Z3N Bluster Thanks! I’ll reevaluate my setting then.
@ecllippse
7 жыл бұрын
what do you recommend for rear roller position/height?
@Z3NBluster
7 жыл бұрын
It depends on the tracks that you want your car to be good at. If you want your car be good at cornering you want the top roller on the rear to be pretty high. As long as it's not too close to the top of the wall. If you want your car to be good at tracks that have alot of straights. You will want to lower the height of the top roller on the rear. A 30mm screw on the back should be fine for this.
@samueleipsale5183
6 жыл бұрын
Dolores??❤️❤️❤️
@marclouiesulit7277
5 жыл бұрын
Sir Jan, may i know what is the weight of this setup? (Excluding the batteries) thank you
@Z3NBluster
5 жыл бұрын
This video is from over two years ago. Dolores has long been taken apart. I can not measure her weight anymore. But if I were to estimate, it was probably between 123-128grams.
@michaeljohnsoriano3096
5 жыл бұрын
hi jan, do you have tutorials on how to make sliding damper?
@Z3NBluster
5 жыл бұрын
Not yet.
@maxchroma07
5 жыл бұрын
Hello sir, how did you convert the super 2 chassis into fm Chassis? how did you reveres the run of the car?
@Z3NBluster
5 жыл бұрын
Look for the video called, "FMS2 Full Build," in my Tamiya Mini 4WD Build Playslist.
@maxchroma07
5 жыл бұрын
@@Z3NBluster thanks a lot :)
@jaylivewire
5 жыл бұрын
Sir ano gamit mo sa front bumber, same item ba yan sa ginamit mo sa rear brake?
@Z3NBluster
5 жыл бұрын
I mentioned the part numbers as I went though the overview.
@valentinusarry1069
7 жыл бұрын
how the performance of this machine to jump ramp?
@Z3NBluster
7 жыл бұрын
Bad. Not designed for jump ramps.
@nathanaeldeleon1622
5 жыл бұрын
whats the clearance on your rear brakes sir?
@Z3NBluster
5 жыл бұрын
Doesn't matter, change your brake clearance depending on the track.
@5milliondollarsindebt385
7 жыл бұрын
wow so fast. looks speed 40 km... magkano gastos mo dyan ?
@Z3NBluster
7 жыл бұрын
Around $250
@joaquindelacruz8650
5 жыл бұрын
How did you make the rear bumper to be the front bumper?
@Z3NBluster
5 жыл бұрын
If you place your batteries in the car in reverse polarities, the car runs backwards instead. Now the rear is your new front.
@joaquindelacruz8650
5 жыл бұрын
I did'nt think about that lol😂
@joaquindelacruz8650
5 жыл бұрын
How can i tried to reverse the batts but it wont work
@Z3NBluster
5 жыл бұрын
@@joaquindelacruz8650 Watch my video called FM S2 Full Build. It sounds like you're doing something wrong. One of your terminals isn't bent to the correct angle.
@joaquindelacruz8650
5 жыл бұрын
Thank you so much sir Zen💪
@bone432
5 жыл бұрын
Hallo sir.. what corona gear is used.? Pink, carbon, or orange.?
@Z3NBluster
5 жыл бұрын
Crown gear? Black Carbon reinforced.
@bone432
5 жыл бұрын
@@Z3NBluster yes, what Is it not fast to damage the gear propeller shaft.?
@Z3NBluster
5 жыл бұрын
@@bone432 I don't understand your question.
@bone432
5 жыл бұрын
@@Z3NBluster I also built FMS2 but it quickly damaged the corona gear and gear propeller
@515paolo
5 жыл бұрын
Where can i find those sliding bumpers online? Thanks
@Z3NBluster
5 жыл бұрын
Ask Mad Tang, he ordered them for me.
@515paolo
5 жыл бұрын
@@Z3NBluster thank you :)
@515paolo
5 жыл бұрын
@@Z3NBluster still no reply from mad tang :(
@markymadz4598
5 жыл бұрын
Hello bro, do you know how to make a sliding dumper? can you make a video as well? :)
@Z3NBluster
5 жыл бұрын
Sometimes next year. I'm slowly building up to it with other videos that need to be made and released first.
@markymadz4598
5 жыл бұрын
got ya... :)
@nerbs6125
6 жыл бұрын
Jesus, Dolores is stable af.
@Z3NBluster
6 жыл бұрын
+nerbs She was. Sadly Dolores has seen too much racing. Two Second Place finishes and 2 Third Place finishes. Never First. Lol.
@neofalconracer9716
5 жыл бұрын
Its so beautiful! My friend did this also and it became champion twice!
@neofalconracer9716
5 жыл бұрын
Thanks for the setup anyway
@webreaver01
5 жыл бұрын
Hi, can you please share the link of that Chinese store where you got that custom sliding damper?
@Z3NBluster
5 жыл бұрын
Ask Mad Tang, he was the one I bought it from. Also don't be surprised if it's expensive :( It's custom cut from OG Tamiya.
@mhenardmhenard3602
5 жыл бұрын
Binaliktad poba Yung battery Nyan sir
@Z3NBluster
5 жыл бұрын
Yes.
@neovergara8769
7 жыл бұрын
kuya pwede mag tanong anong chassis yang blue
@Z3NBluster
7 жыл бұрын
I mentioned it in the video. It's Super 2 Chassis.
@samefraimlegnis6544
6 жыл бұрын
cowl is thunder shot junior. chassis is S2.
@samefraimlegnis6544
6 жыл бұрын
How much po magpagawa sa inyo ng ganitong auto? salamat po.
@Z3NBluster
6 жыл бұрын
I don't build to sell cars. If I were going to price this car out with parts and labor, I would sell it for $300.
@samefraimlegnis6544
6 жыл бұрын
Z3N Bluster: P15,000 if I converted 300 dollars. do you have lower price?
@roncabais4362
6 жыл бұрын
haha normal lang yan 15k.. dati nga 25k nagastos namin for a ultradash setup ms chassis
@FrancisJohnSedanFWPL
5 жыл бұрын
Nasa magkano kaya nagastos mo jan sir?
@Z3NBluster
5 жыл бұрын
I listed all the parts. You can probably compute it with the value of the Peso. I think it was around $200-$250 here.
@FrancisJohnSedanFWPL
5 жыл бұрын
@@Z3NBluster ohh okay sir. May kakaron kasi samin ng event kaya nag babalak kami bumuo huling laru ko nyan bata pako 15yrs ago. Salamat sir.
@TheChickybastard
6 жыл бұрын
Can i buy your car?
@Z3NBluster
6 жыл бұрын
No, I took it apart already.
@geohabitat
6 жыл бұрын
Sir do you have facebook account? Can add you?
@Z3NBluster
6 жыл бұрын
Just contact me on my instagram. Username: z3nbluster
Пікірлер: 76