Good to know, my S1 L400 pump is still going well, but it helps to have this sort of information. Hope to see more on the 4m40
@manealaughlin8230
3 жыл бұрын
Thank you, my vehicul is a 2.8Turbo diesel , so i have to put the Notch at the (T) mark 🙏thanks.
@sameuljones5496
3 жыл бұрын
I want to turbocharge my non turbo 4m40 so should I adjust my pump to T mark once I slap this big turbo on and wind it up to 30psi of boost?
@cobra646
2 жыл бұрын
Here is a link to a directory from the Delica Canada forum that includes engine manuals for the 4M40 and 4M41, including procedures for removing and installing fuel pump www.delica.ca/manuals/L-400%20Manuals%20&%20Plans/
@bushmechanic-howtofixyourcar
2 жыл бұрын
Thanks so much 🙏🏽I lost my manuals years ago could never find them again no matter how much I searched on google 🙏🏽
@jeffn1384
3 жыл бұрын
So is it reinstalled when number 1 piston is at top dead centre?
@bushmechanic-howtofixyourcar
3 жыл бұрын
Yes
@roshsookraj790
Жыл бұрын
How many degrees before top dead centre must it be set.
@Armageddon-qo4wy
2 жыл бұрын
Are those factory notches on the gear or did you put those in yourself
@bushmechanic-howtofixyourcar
2 жыл бұрын
They are factory notches
@robwhite240z
4 жыл бұрын
So do you set it at that point. then slide it on, or slide it on to that point . As sliding on will move it 1 whole tooth over.
@bushmechanic-howtofixyourcar
4 жыл бұрын
you slide it on to that mark so you offset it and slide on to point
@Free-j3t
3 жыл бұрын
That’s a critical piece of info you left out
@jasper232
3 жыл бұрын
What is the brand and model of this injection pump? Thanks
@ahmeed363
2 жыл бұрын
سؤال لدي سيارة باجيرو وعندما تم اصلاح مضخة الوقود لم تعد تعمل صباحا الا عندما اسحبها بسيارة اخرة هل يكون هذا السبب
@ahmeed363
2 жыл бұрын
او انه لم يتم ضبطها بشكل صحيح
@bhenchannel11
2 жыл бұрын
great bro stop by on the channel
@odenwaldcruise4794
3 жыл бұрын
What is happening when you install the Pump with non Turbo timing mark in a Turbo vehicle ?
@bushmechanic-howtofixyourcar
3 жыл бұрын
It will cause your vehicle to run badly , because it will not be getting correct amounts of fuel for engine with turbo.
@usmaanbhai
4 жыл бұрын
hi , whats the firing order of 4M40 ?
@Cypher-Six
4 жыл бұрын
I was told that when you put it back into the car it moves one notch when you slide it in, is this actually correct?
@siyabongamakhathini
4 жыл бұрын
yes it is correct , this is because when you slide it in and it touches the gears it moves slightly. I prefer to move it half a notch rather than a full notch
@Cypher-Six
4 жыл бұрын
@@siyabongamakhathini so does it need to be set one notch back from the T so it is on the T when it goes in? or on the T before it goes in so it moves forward when fitted?
@siyabongamakhathini
4 жыл бұрын
@@Cypher-Six it needs to set half a notch ( move it slightly above T so notch is slighly above T arrow ) before installalation so when fitted it will push the marks to align
@AndrewBarnard-kr3up
Жыл бұрын
But when you install the pump... themark moves from the T to N
@bushmechanic-howtofixyourcar
Жыл бұрын
place mark one tooth before T so when you install it moves to the T
Пікірлер: 29